Anderson 680HS User manual

This Quick start up guide does not replace in any way or form the
user manual of this unit. The intension of this document is for use
when setting up the machine after delivery to the dealer and before
the machine is transferred to the end user. This document should
be used as a checklist and memory aid for employees already
familiar with the guidelines in the user manual. Failure to operate
the product correctly can result in damage to the product, personal
property, and cause serious injury. This guide should not be
transferred to the owner of the machine.
QUICK START GUIDE
800HS

After receiving your machine you will want to set it up to be ready for any demo opportunity or sale
that may come along.Besides that, you want to be sure that the machine is in factory condition, free
of damage from transport and defective parts due to the transport from our factory to your dealership.
This is aquick guide that will help you to be up and ready in ashort time.Before using the machine
you must grease and oil all points on the wrapper that require it.
Basics:
Square bale wrapper
•Up to 6ft bale
•1 stretcher (30’’)
•Computer & remote
•Hydraulic plastic cut and hold
Note: Before pressure washing the machine be sure to remove the computer
QUICK START GUIDE
800HS
12
3
5
7
8
9
10
6
4

QUICK START GUIDE
800HS
When the machine is to be delivered to the user there are steps you must follow to be sure they are
comfortable with wrapping their first bale. These steps are also important if you are doing a live demo.
Setup is very important to bale size as this machine is not set to a specific bale at the factory.
1) Know your bale size before you start. Asking can help but an actual measurement of
the bale is sometimes necessary.
2) Be sure that everything is greased (if left for more than 3 months outside without use
the machine needs to be fully greased and oiled.
3) Your remote control is charged and tested operational (see user manual on machine for
functions).
The stretcher pole has 6 positions. Be sure that the position is
not over the height of the bale or under it. (this part could have
been removed for shipping so be sure to install it correctly for
wrapping bales)
Set the cone rollers for the size of
your bale.
Put plastic in the
stretcher. There is only
one way to put the plastic
through. See the diagram
to the left. This is a
sticker found on the
machine as well.

Turn on the computer.
1) Pull the emergency stop button (1), the blue
light (2) will come on.
2) Press the power button on the remote (3),
when the screen is ON push the power button
(3) again
3) Make sure the M.C. LED light (4) on the
receiver’s control panel is ON.
QUICK START GUIDE
800HS
Starting and Aligning the wrapper
1) If equipped with an Honda engine, put the
ignition key in the ON position and press the
start engine button on the remote.
2) Before wrapping you need to align the
wrapper, press the alignment key (5) on the
remote control.
3) When the alignment menu appears on the
remote control screen, press the same key (5)
asecond time, the alignment will start and the
screen should display Alignment in progress (it
can take up to 2minutes).
Receiver
Remote
Emergency control box
1
2
3
4
5
Start Wrapping
1) Make sure the blue button’s light (2) is on,
which means that the alignment is finished.
2) Push the wrap key (6), the wrapper’s table will
make the set number of rotation and
unloading will happen automatically, and will
engage the plastic cutter.
3) If the remote is not charged or missing you can
wrap automatically by pressing the blue
button (2).
6
Honda engine
The 800HS is powered by an Honda
engine.Before starting the machine
make sure it has gas and oil in it.Also
when traveling or not using the
machine for along period of time don’t
forget to close the fuel valve, located
beneath the choke on the right side of
the engine.
Fuel valve

QUICK START GUIDE
800HS
The 680HS is equipped with an
hydraulic cut and hold system.The
hydraulic cut and hold works with
the pressure of the main valve and
an accumulator.
If the plastic isn’t cut or not
completely you want to make sure
the blade is sharp and free of rust
first.If the rubber bumper doesn’t
hold the plastic you can put more
tension on the fingers and rubber
bumper by adjusting the bolt (1)
and the spring with the adjustment
rod (2).
1
2