Anderson Hybrid-X Installation guide

Product range overview
Hybrid-X
• Square & round wrapper
• Equipped with patented hydraulic push
off system “ XTractor™”
• Equipped with “Advanced Flex
HoopTM” Technology
• Round bale size:
Up to 6’ diamete
r
4’ or 5’ length
• Square bale size:
Up to 6
’
length
Up
to
6
length
•Wrap up to 180 bales / hour

Hybrid-X start up
1. Remove the tongue and put it at its storage place (close to the steering wheel under the
left fender);
2
Unlock
the
front
gate
;
2
.
Unlock
the
front
gate
;
3. Make sure that the gas tank is full;
4. If the wrapper has the high capacity gas tank, open the valve under the tank and select the
tank with the selector valve (close to the Honda engine);
5
Connect
the
battery
wires
;
5
.
Connect
the
battery
wires
;
6. Start the engine with the green button on the control panel (make sure that the ignition
switch is at ON position and pull out the emergency stop button);
7. If necessary, unlock the steering wheels by removing the lock pin close to the wheel (under
the
automatic
system)
;
the
automatic
system)
;
8. Find out the best wrapping area and put the machine there;
9. With the lifting lever (on the main valve), level the machine to avoid the first bales from
falling;
10
Lower
the
front
gate
(with
the
lever)
;
10
.
Lower
the
front
gate
(with
the
lever)
;
11. Adjust the bale guides enough tight so that the tube has a nice line;
12. For square wrapped bales, raise up the front table rollers (with the handle);
13. For round wrapped bales, let down the front table rollers (with the handle);

Hybrid-X start up
14. Adjust the guide rollers (near the traction wheels) according to the bale size (round or
square);
15
Test
the
pusher
and
hoop
stroke
manually
by
using
the
automatic
system
trigger
handle
15
.
Test
the
pusher
and
hoop
stroke
manually
by
using
the
automatic
system
trigger
handle
.
Then, proceed to the adjustments (hoop start, return of the pusher) that will insure the
good overlap of the plastic film between the bales. Refer to the sticker on the machine for
more details;
16
Test
the
X
-
Tractor
system
by
using
the
lever
(on
the
main
valve)
;
16
.
Test
the
X
Tractor
system
by
using
the
lever
(on
the
main
valve)
;
17. Verify that the hand held remote control is working well:
Close the emergency stop and reopen it;
Turn on the blue button on the control panel;

Push
on
the
button
of
the
remote
control
to
start
the
engine
(full
throttle)
;

Push
on
the
button
of
the
remote
control
to
start
the
engine
(full
throttle)
;
Use the arrows to turn the steering wheels both sides;
Push on the button to engage the auto-pilot;
To change the auto-pilot sensor side, push on the button;

To
close
the
engine
push
on
the
button
;

To
close
the
engine
,
push
on
the
button
;
Push on the blue button to open the working lights;

Hybrid-X start up
18. Install the plastic rolls:

Pull
off
towards
the
back
of
the
machine
the
manual
hoop
trigger
(handle
under
the

Pull
off
towards
the
back
of
the
machine
the
manual
hoop
trigger
(handle
under
the
control panel);
Start the Honda engine;
Turn slightly the hoop speed valve handle to turn the hoop so the stretcher goes at
the
best
position
for
the
plastic
film
installation
;
the
best
position
for
the
plastic
film
installation
;
Open the safety gate (the engine will cut off automatically);
If needed, turn the ball valve (brake valve) beside the safety gate handle to brake
the hoop while the plastic film installation;

Install
the
plastic
film
roll
within
the
2
aluminum
holders
.
It
is
really
important
to

Install
the
plastic
film
roll
within
the
2
aluminum
holders
.
It
is
really
important
to
install the adjustable holder perfectly. If it is not well locked, it could damage
some components;
Follow the instructions on the sticker to install the plastic film through the stretcher
rolls
;
rolls
;
Pull out the plastic film forming a knot and hold it in the fingers (at the end of a bale
guide) and repeat for each stretcher;

Hybrid-X start up
19. Engage the plastic watch (automatic hoop stopper if broken or missing plastic);
20. Turn the handle (Wrapping/Moving) on the control panel towards the right to
Wi
«
W
rapp
i
ng »;
21. Adjust the compaction between the bales (traction wheels brake) with the adjustable
screw (at the left on the control panel). It should be between 500 and 1000 PSI
depending of the conditions (ground, incline of the yard, bales weight, etc);
22
Adj t
th
h
d
(d di
f
th
b
f
l
dd
)
ith
th
l
hdl
22
.
Adj
us
t
th
e
h
oop spee
d
(d
epen
di
ng o
f
th
enum
b
e
r
o
f
l
ayers nee
d
e
d
)
w
ith
th
eva
l
ve
h
an
dl
e
on the control panel;
Consult the operator manual for more information about the installation of the first and
th
lt
bl
f
tb
th
e
l
as
t
b
a
l
eo
f
a
t
u
b
e.