Anderson RB-200 User manual

This Quick start up guide does not replace in any way or form the
user manual of this unit.The intension of this document is for use
when setting up the machine after delivery to the dealer and before
the machine is transferred to the end user.This document should
be used as achecklist and memory aid for employees already
familiar with the guidelines in the user manual.Failure to operate
the product correctly can result in damage to the product, personal
property, and cause serious injury.This guide should not be
transferred to the owner of the machine.
QUICK START GUIDE
RB200

After receiving your machine you will want to set it up to be ready for any demo
opportunity or sale that may come along.Besides that, you want to be sure that the
machine is in factory condition, free of damage from transport and defective parts due
to the transport from our factory to your dealership.This is aquick guide that will help
you to be up and ready in ashort time.Before using the machine you must grease and
oil all points on the wrapper that require it.
Basics:
Single bale 3 point hitch wrapper.
•4 or 5ft bale
•1 stretcher (30’’)
•Plastic cutting knife
•Bale counter
Note: Before pressure washing the machine be sure to remove the computer (bale counter)
QUICK START GUIDE
RB200

QUICK START GUIDE (WITHOUT BALE)
RB200
Hook the machine to atractor to test it.Be sure that the tractor and the machine
are secured by the pins supplied with the machine.(See the below illustrations)
Attach the machine’s hoses to the tractor as
shown.Be sure that your tractor has enough
oil and follows the below requirements.
Remove the transport locking pin.Once
removed, the wrapper will split when lifted by
the 3point hitch on the tractor.This will cause
the bale to dump from the machine to the rear.

QUICK START GUIDE (WITH BALE)
RB200
When the machine is to be delivered to the user there are steps you must follow to be sure they are
comfortable with wrapping their first bale. These steps are also important if you are doing a live demo.
Setup is very important to bale size as this machine is not set to a specific bale at the factory.
1) Know your bale size before you start. Asking can help but an actual measurement of
the bale is sometimes necessary.
2) Be sure that everything is greased (if left for more than 3 months outside without use
the machine needs to be fully greased and oiled.
3) Your bale counter is charged and tested operational (see user manual on machine for
functions).
4) Be sure the tractor you are using is open center hydraulics and can handle the machine
weight.
The stretcher pole has 3 positions. Be sure that the position is
not over the height of the bale or under it. (This part is normally
removed for shipping so be sure to install it correctly to wrap
your bales)
Set the cone rollers for 4 or 5 foot
long bale.
Put plastic in the stretcher. There
is only one way to put the plastic
through. See the diagram to the
left. This is a sticker found on the
machine as well.

QUICK START GUIDE (WITH BALE)
RB200
Turn on the bale counter and set it up.
1) Press the ON button
2) You will have to set the counter up.To do so you will hold the Adjust Select for
3seconds.You can then scroll through 4menus with the same button (adjust
select)
3) Use the +and –to change the values in the menu.
4) When wrapping you will hear abuzzer from the counter on the last turn so
that you know when to stop turning the table.The number will automatically
reset once the sequence is finished.
Quick reference for correct plastic layers:
The way that we calculate the amount of plastic to apply on a bale is simple. You wrap the bale manually
once with only one layer of plastic. You do not want to see any part of the bale when you are finished. You
take the number of turns it took the table to do so and multiply it by 2 and then add one extra layer (or turn).
EX: 10 turns to completely cover the bale x 2 = 20. plus one layer = 21.
This is the number you want to program in your bale counter with.
Last step before wrapping a bale is to uncover the cutting knife.
For the first bale you can put the plastic like the
below image and sit a bale on the machine
Your bale is wrapped. Dump off with the 3 point of the tractor and load another bale.
Note: when dumping the bale, if you dump a little bit to one side (opposite the stretcher) you can sit your next bale directly on the tail of
plastic. When you start to turn the table the plastic will stay there and also cut from the previous bale as soon as you turn the table one turn.
Videos can be found on our website and also more in depth information in the user manual for the machine.