Anova Rendezvous L1387 User manual

anovafurnishings.com
888.535.5005 tel
OR
ASSEMBLY INSTRUCTIONS
L1387 4-Seat Rendezvous Table with Flat Seats
L1388 4-Seat Rendezvous Table with Contour Seats
L1448 4-Seat Latitude Table with Flat Seats
L1449 4-Seat Latitude Table with Contour Seats
TOOLS NEEDED:
Ratchet with 1/2” Socket•
1/2” Open End or Box End Wrench•
5/32” Allen Wrench•
Rubber Mallet•
4 x
Plug
40 x
5/16 X 1.0”
Hex Head Bolt
ASSEMBLY:
The assembly is a two-person operation.
Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.
Assemble the Table over the shipping packaging or padded work area to avoid scratching the product.2.
NOTE: Before assembling the Nuts to the Bolts, it is recommended that a light oil or petroleum jelly be applied to the screw threads.
Open the Hardware package and nd the ve black plastic Plugs. Insert a Plug in the hole on the bottom of each of the Seat3.
Supports. Use the Rubber Mallet to seat the Plugs.
TABLE COMPONENTS:
4 x Seat Support
1 x Lower Leg
Bracket
40 x
5/16” Flanged Nut
OR
1 x Table Top
ASSEMBLY HARDWARE: Extra hardware may be included.
80 x
5/16” Flat
Washer
4 x Seat Mount
12 x
1/4” Flat Washer
1 x Table Top Pan
Plug
Seat Support
12 x
1/4 x 1.5” Button
Head Allen Screw
4 x Flat or Contour Seat
(Seat pattern may vary)
Rendezvous models shown
seat shape and pattern may vary

2 of 4
Locate the Lower Leg Bracket. Install a 5/16”4.
Flat Washer on one of the 5/16” Hex Head Bolts
and insert the Bolt through one of the mounting
holes in the Lower Leg Bracket and into the
lower mounting hole in one of the Seat Supports.
Place a 5/16” Flat Washer and Flanged Nut on
the end of the bolt and tighten nger tight.
Table Top Pan 5/16” Hex Head Bolt
Seat Support
5/16” Flat Washer
Seat Support
Flanged Nut
5/16” Flat Washer
Seat Support
Lower Leg Bracket
5/16” Bolt
5/16” Flat Washer
Flanged Nut
5/16” Flat Washer
Packing cardboard or
other so work surface
Repeat Step 4 for the remaining Seat Supports5.
using 5/16” Bolts with a 5/16” Flat Washer
on the top and bottom and Flanged Nuts to
secure. Leave the hardware nger tight until
aer the Table Top Pan is secured (Step 7).
Locate the Table Top Pan and place it on top of the platform created by the raised ends of the Seat Supports. Adjust the6.
placement of the Table Top Pan until one set of mounting holes in the Pan align with the corresponding set of mounting holes in
one of the Seat Supports.
Place a 5/16” Flat Washer on the end of one of the 5/16” Hex Head Bolts and insert the Bolt through the Pan mounting hole in
the inner bolt circle and through hole in the Support. Fasten the Bolt using a 5/16” Flat Washer and Flanged Nut on the bottom
of the Bolt. Leave the Bolt and Nut nger tight. Repeat this for the remaining four 5/16” Hex Head Bolts. You may have to adjust
the Seat Supports or the Table Top Pan in order to get the mounting holes to align.

3 of 4
Place a 1/4” Flat Washer on the end of one of the 1.5” long Button Head Allen Screws and insert the screw through one of the7.
Pan mounting holes in the outer bolt circle and into the corresponding threaded hole in the Seat Support. Leave the Screw nger
tight. Repeat this for the remaining 1/4” Button Head Allen Screw locations in the top of the Table Top Pan. You may have to
adjust the Seat Supports or the Table Top Pan in order to get the mounting holes to align.
Aer all the Button Head Allen Screws are installed, tighten all of the hardware in the Lower Leg Bracket and in the Table Top
Pan. Be careful not to over tighten the Button Head Allen Screws; the inserts they thread into could unseat and begin to spin
with the Screw.
Seat Support
Mounting Plate
Table Top Pan
5/16” Hex Head Bolt
1.5” Long Button
Head Allen Screw
1/4” Flat Washer
1.5” Long Button
Head Allen Screw
1/4” Flat Washer
5/16” Flat Washer
Flanged Nut
5/16”Flat Washer
5/16” Hex Head Bolt
5/16” Flat Washer
Flanged Nut
5/16”Flat Washer
Seat Mount
Locate one of the Seat Mounts. Position the Seat Mount on the lower end of one of the Seat Supports so that the mounting8.
holes in the Seat Mount align with the mounting holes in the Seat Support Mounting Plate. Install four 5/16” Hex Head Bolts
with 5/16” Flat Washers (top and bottom) and Flanged Nuts.
Install the remaining Seat Mounts in the same manner.

Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to•
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,•
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced.•
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: [phone]
web: anovafurnishings.com
11/2012
Li the Table Top and move it over the top of the Table Top Pan. Rotate the Table Top until the square frame on the bottom of the9.
Table Top matches the orientation of the Table Top Pan. Carefully lower the Table Top down onto the Table Top Pan.
Secure the Table Top to the Table Top Pan using the remaining eight 1.5” long Button Head Allen Screws (2 screws on each side)
with a 1/4” Washer on each of the Screws. You may have to li the Table Top slightly to get the holes to align.
Leave the Screws nger tight until all the Screws are started, then use the 5/32” Allen Wrench to tighten the Screws. Be careful
not to over tighten the Screws; the inserts they thread into could unseat and begin to spin with the Screw.
5/16” Flat
Washer
5/16” Hex
Head Bolt
5/16” Flat
Washer
Flanged Nut
5/16” Flat Washer
5/16” Hex Head Bolt
5/16” Flat Washer
Flanged Nut
Contour Seat
OR
Flat Seat
Table Top
Table Top Pan
1.5” Long Button
Head Allen Screw
1/4” Flat Washer
1.5” Long Button
Head Allen Screw
1/4” Flat Washer
Place one of the Seats (Flat or Contour) over one of the Seat Mounts. Use four 5/16” Hex Head Bolts with 5/16” Flat Washers10.
(inside and outside) and Flanged Nuts.
Install the remaining Seats in the same manner.
NOTE: Extra hardware may be included.
Move the Table to the location where it will be used.11.
Aer two weeks, retighten all hardware.12.