Anova Infinity Modular Seating System User manual

Assembly Instructions
Component parts:
Hardware Needed:
1
Contact Us:
800.231.1327
[email protected]om
Tools Needed:
• 3/4” Hex Wrench
• 3/4” Hex Socket with Ratchet
• 7/16” Hex Wrench
• 7/16” Hex Socket with Ratchet
• Retractable Measuring Tape
• Pencil
Innity Powder Coated Benches
Innity Modular Seating System
Single Section Assembly:
Seating Sections End Caps Joining Straps Supports
1/2" Stainless
Steel Washers
1/4" Stainless
Steel Washers
1/2"-13 x 1.25" Stainless
Steel Hex Head Bolts
1/4"-20 x 1" Stainless
Steel Hex Head Bolts
1/2"-13 Stainless
Steel Hex Nuts
1/4"-20 Stainless
Steel Hex Nuts
Supports End Caps and Joining Straps
NOTE: Before assembly, it is recommended that a light oil or petroleum jelly be applied to screw threads. During
initial assembly, only tighten hardware to nger-tight until assembly is complete. Assembly of any Innity
bench requires at least two people.
1. Inspect the shipping container contents for damaged or missing components. Quantities will vary depending on
conguration and order.
a. Lay all parts on a soft work surface or on the shipping packaging to prevent damage to nish. It is
recommended that the parts be positioned where the bench will be installed as once the bench is fully
assembled it may be too big and heavy to reposition.
!

2
Innity Powder Coated Benches
Assembly Instructions
2. Locate the End Caps to the bench and attach them
to the end of the bench using the included end cap
hardware.
a. For Linear Sections: Find one of the
two identical End Caps and slot it into the
end of the bench. Repeat this step on the
other end of the bench. Secure the End Cap
to the Seat Section using the included end
cap hardware with a 7/16”socket set and
wrench. (congure hardware in assembly as
shown below).
b. For Curved Sections: Determine the Left
and Right End Caps and slot them into the
end of the bench. Repeat this step on the
other end of the bench. Secure the End Cap
to the Seat Section using the included end
cap hardware with a 7/16”socket set and
wrench. (congure hardware in assembly as
shown below).
c. If you are assembling multiple sections
together, the End Cap will only be installed
on the end of the total bench not each
section. Continue to next page for Multiple
Section Assembly.
3. Position the Seat Section on top of the Supports
by lining up the holes on the underside of the
Seat Section to the mounting tabs on top of the
supports. Secure the Seat Section to the Supports
by using the included support hardware with a
3/4” socket set and wrench (congure hardware in
assembly as shown below).
Bolt Washers Nut
1
2a
3
2b
Support SupportSeat Section
End Cap End Cap

3
• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,
missing, or broken hardware, and general instability
• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced
• Repairs must be made using only factory authorized parts and methods.
WARNING
• Do not drag the assembled unit across any surface.
• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove
surface dirt. Do not clean with a solvent or petroleum based products.
CARE AND
MAINTENANCE
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
09/27/2022 Copyright 2022 Anova ® Manufactured in the U.S.
Innity Powder Coated Benches
Assembly Instructions
Assembling Multi-Section Innity Benches:
4. If assembling bench sections together into a
larger modular unit, assemble each section in the
modular unit and align the benches end-to-end.
5. Use Joining Straps to connect each section of
the modular bench together. The Joining Straps
will vary depending on the radius of your bench
section. When assembling, the faces of the
Joinings Straps should be ush with the outer
faces of the Seat Section Supports. Secure the
Joining Straps to the two Seat Sections using
the included joining strap hardware with a 7/16”
socket set and wrench.
REMINDER: It is recommended that the hardware
used in the assembly only be hand-tight until the
entire unit is assembled.
6. Once the modular bench is completely
assembled, be sure to install the End Cap on the
opposite end of the run of benches by repeating
Step 2.
4
5a 5b