Assa Abloy Sargent 6-Line User manual

Installation Instructions
1-800-727-5477 • www.sargentlock.com A6286M 4/20
Copyright © 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission ofSARGENT Manufacturing Company is prohibited.
WARNING
This product can expose you to lead which
is known to the state of California to cause
cancer and birth defects or other reproductive
harm. For more information go to www.
P65warnings.ca.gov.
6-Line
Bored Lock
Attention Installer:
Please read these intructions carefully to prevent missing important steps.
Note:
Improper installation may result in damage to lock and void factory warranty

2
6 Line
Installation Instructions
Bored Lock
A6286M 4/20
Copyright © 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
TOC Table of Contents
1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
a Install Latch Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
b Remove Inside Knob or Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
c Adjust for Door Thickness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
d Install Lock Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
e Attach Inside Rose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
f Replace Inside Knob or Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2 Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1 Installation
a Install Latch Unit
• Prepare door and jamb according to
template provided. Mount latch unit in
door.
Remove Inside Knob or Handle
b
• If received with knob or handle engaged depress
knob catch with screw driver and pull knob or
handle off spindle.
Notes
Locks with threaded inside roses do not have retainer
plates. Unscrew to remove.

3
6 Line
Installation Instructions
Bored Lock
A6286M 4/20
Copyright © 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
1 Installation (continued)
Adjust for Door and Thickness
c
• Rotate outside rose in or out, depending on door thickness.
Lock will fit any door from 1 3/8 “ to 1 3/4”.
Install Lock Unit
d
• Lock unit housing must engage latch unit prongs and
retractor must engage latch tailpiece.
Notes
If guard bolt function is installed, do not attempt to mount lock
unit when door is closed. Guard bolt tailpiece will interfere.
Depress latch bolt slightly to allow retractor to engage latch
tailpiece.
Attach Inside Rose
e
• Snap on roses: Slip on retainer plate and fasten with two
machine screws. Position spring clip notch and snap rose
over retainer plate.
• Threaded type roses: Slip rose over spindle and screw
down firmly using trim wrench provided.
Replace Inside Knob or Handle
f
• Line up slot in shank with knob catch in spindle. Slide knob
or handle on to spindle. Depress knob catch and push knob
or handle into engaged position.
Note
B knob sets should be in the unlocked position when replacing
the inside knob or handle
Note
When a cylinder function lock is correctly installed, the key
should enter in this position
For 6U65 function
In an emergency, entrance to a locked door can be gained by inserting
a flat blade screwdriver into slot located in the center of the outside
button head.

Founded in the early 1800s, SARGENT®is a market leader in locksets, cylinders, door closers, exit devices,
electro-mechanical products and access control systems for new construction, renovation, and replacement
applications. The company’s customer base includes commercial construction, institutional, and industrial
markets.
Copyright © 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part
without the express written permission ofSARGENT Manufacturing Company is prohibited..
SARGENT Manufacturing Company
100 Sargent Drive
New Haven, CT 06511 USA
800-727-5477
www.sargentlock.com
A6286M 4/20
1 Reassembly
2
FOR ALL FUNCTIONS
When the cylinder has been removed completely as for purposes of rekeying], reassemble as follows:
STEP 1
A. Slip knob collar over shank
B. Insert cylinder fully, engaging tail piece
C. Slip knob on until it bottoms against knob catch A
B
C
STEP 2
• Insert key fully into cylinder, press a small
nail into the outside knob sleeve hole.
Turn key (in clockwise direction) approx. 45º or
until depression of the knob catch is felt with
nail. Checking alignment of cylinder head with
hole in knob, push knob until knob catch “clicks”
into position. Pull collar back into proper posi-
tion against knob.
Note
For 37 & 38-2 functions, check to determine that the slotted member which engages the cylinder tail piece has
been rotated clockwise fully and lies in a vertical position.
If not, reverse cylinder as follows:
1. Insert key fully into cylinder.
2. Press a small nail into the outside knob sleeve hole.
3. Turn key (in clockwise direction) aprox. 45º or until depression of the knob catch is felt with nail; pull off
knob.
4. Rotate knob 180º (so that keyway is vertical and down). Push knob on to shank until it contacts knob
catch.
5. Release knob catch by pressing Knob Release Tool into the outside knob sleeve hole; turn key (in clockwise
direction) approx. 45º or until depression of the knob catch is felt.
6. Checking alignment of cylinder head with hole in knob, push knob until knob catch “clicks” into position.
1 Installation (continued)