Assa Abloy Sargent 7800 Series User manual

Installation Instructions
1-800-727-5477 • www.sargentlock.com A8130D 02/20
Copyright © 2011, 2020, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
7800 Series
with PT Paddle Trim
Mortise Lock

2
7800 Series
Installation Instructions
Mortise Lock with PT Paddle Trim
A8130D 02/20
Copyright © 2011, 2020, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
1 Tools Required
.
• Phillips Screwdriver #2
• Drill
• 7/46” Drill Bit (Wood Door)
• #8-32 Tap (Metal Door)
• 0.136 (#18) Tap Drill
• Screw Pack with screws for lockbody, fronts &
strike screws (part #77-4236)
• T15 Torx Bit
• 1/8” Allen Key
2 Installation of Lock
• Slide Lock into the door.
• Secure lock in door with (2) wood screws #12
x 1-1/4” or machine screw #12-24 x 1/2”.
• Do not tighen screws fully at this point.
TOC Table of Contents
1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2 Installation of Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
3 Installation of Cylinder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
4 Determine Orientation and Handing of Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
5 Installation of Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
6 Installation of Paddles and Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
7 7800 PT Multi Function Lock Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
a How to Change Function of Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
b Item Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
c How to Change Hand of Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3
7800 Series
Installation Instructions
Mortise Lock with PT Paddle Trim
A8130D 02/20
Copyright © 2011, 2020, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
3 Installation of Cylinder
For non-cylinder functions, proceed to STEP 4
• Thread the cylinder into the lockbody.
• Verify the cylinder is flush with the collar and the logo is horizontal.
• Secure cylinder with cylinder clamping screw located above the deadbolt opening.
• Verify the cylinder functions correctly.
4 Determine Orientation and Handing of Trim
The trim can be mounted vertically or horizontally.
• Down or horizontal paddle orientation is required for cylinder side of door.
• Horizontal paddle orientation is required if thumb turn or an emergency release is used.
• To change from PUSH to PULL orientation, chassis will need to be turned 180º and paddle
installed in the correct direction.
NOTE: Chassis is packed with the paddle attached. Remove paddle before installing. Before
installing chassis to door, confirm the spring orientation is correct.

4
7800 Series
Installation Instructions
Mortise Lock with PT Paddle Trim
A8130D 02/20
Copyright © 2011, 2020, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
5 Installation of Chassis
• Check handing of chassis before installing
mounting screws.
• Insert the (2) mounting posts through the out-
side chassis, then secure with (2) #8-32 x 5/8”
machine screws through the inside chassis.
Do not tighten fully at this point.
• Lockbody screws on edge of door are to be se-
curely fastened at this point.
• Level chassis.
• Tighten thru bolt screws.
• Attach the outside front plate to lock front with
(2) #8-32 x 1/4” flat head screws.
• Tighten all screws firmly. Do not over tighten.
6 Installation of Paddles and Covers
•Insert paddle in slot.
• Install set screw.
•Slide cover over paddle and align with mounting holes.
• Install cover screws.

5
7800 Series
Installation Instructions
Mortise Lock with PT Paddle Trim
A8130D 02/20
Copyright © 2011, 2020, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
The green catch screw must be located as
designated on lock case to create desired function.
3 locations:
•One for 05, 37 & 38 functions
(15 function in unlocked position)
•One for 04, 06, 13, 17 & 31 functions
•One for 36 function
NOTE: When moving green catch screw to 04, 06,
13, 17 & 31 functions, hub position must be at
45° as shown on lockcase.
NOTE: 17 function requires both levers to be rigid.
Rotate red locking piece 90°, so red surface of
slide faces back of lockbody.
7800PT lockbody is required when using PT pad-
dle trim, 8200 lever lockbody will not function
properly with the PT trim
Function Outside
Lever Inside Lever Trim One Side Kit
Outside
Cylinder
Inside
Cylinder Thumb Turn
04 X X X
05 X X X X***
06 XXX
13 X X
17 X X X X
31 XXX
36 XXX
37 X X X
38 X X X X
#41Cylinder is standard for both single & double cylinder functions for 1-3/4” thick door
NOTE: Trim-one-side functions always require an inside trim assembly which can be used on the
inside or outside of the door
7 7800 PT Multi Function Lock Instructions
a How to Change Function of Lock
b Items Needed to Create Each of the Following Functions

6
7800 Series
Installation Instructions
Mortise Lock with PT Paddle Trim
A8130D 02/20
Copyright © 2011, 2020, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com
7 7800 PT Multi Function Lock Instruction (continued)
c How to Change Hand of Lock
NOTE: Red surface of locking piece must face secure
(keyed/locked) side of door.
To rotate locking piece:
1. Position lockbody with red surface of locking piece visible.
2. Insert blade type screwdriver into locking piece slot to rotate
locking piece.
3. Push locking piece toward back of lock body and rotate 180°
until RED surface shows on opposite side.
NOTE: 04, 06, 13, 17 and 31 Functions require:
(a) Green catch screw to be removed.
(b) Rotate hub 45° to vertical position.
(c) Rotate locking piece for required hand.
(d) Red surface faces locked side of door.
(e) Rotate hub to the original 45° position as shown on lock-
case.
(f) Green catch screw is then reinstalled.
NOTE: Beveled surface of latch must face strike. The deadlatch is self
adjusting. To change hand of latch:
2. Rotate screwdriver 90º to push latch out
until back of latch clears lock front. Then
rotate latch 180º. Latch will then re-enter
lockbody. (Note: Latch can not be un-
screwed)

7
7800 Series
Installation Instructions
Mortise Lock with PT Paddle Trim
A8130D 02/20
Copyright © 2011, 2020, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole
or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.
1-800-727-5477 • www.sargentlock.com

Founded in the early 1800s, SARGENT®is a market leader in locksets, cylinders, door closers, exit devices,
electro-mechanical products and access control systems for new construction, renovation, and replacement
applications. The company’s customer base includes commercial construction, institutional, and industrial
markets.
Copyright © 2011, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in
part without the express written permission ofSARGENT Manufacturing Company is prohibited..
SARGENT Manufacturing Company
100 Sargent Drive
New Haven, CT 06511 USA
800-727-5477
www.sargentlock.com
A8130D
02/20