Assa Abloy ADAMS RITE 4300 Series User manual

1 80-0180-418, Rev D
4600 Heavy Duty Designer Deadlatch Handles With
4300, 4500, and 4900 Series Deadlatches
Installation Instructions
TABLE OF CONTENTS
Tools and Equipment Needed ........................................................................................................ 2
Preparing the Stile........................................................................................................................... 2
Offsetting the Escutcheon for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset........................ 4
Optional Monitoring Switch ............................................................................................................. 4
Installing Trim to Stile...................................................................................................................... 5
Installing the Handle........................................................................................................................ 6
Determining and Changing the Handing Configuration.................................................................. 7
Changing the Handing of the 4581 Cam Disc................................................................................. 7
Phoenix, AZ
Tel: [phone]
Mon-Fri: 6:00am - 4:00pm PDT
Fax: [phone]
www.adamsrite.com

2 80-0180-418, Rev D
IMPORTANT: This product must be installed according to all applicable building and
life safety codes!
Tools and Equipment Needed
The following common hand tools are needed for installation:
• 7/32” [5.56 mm], 1/4” [6.35 mm], and 3/8” [9.53 mm] drill bits
• 3/32” [2.38 mm] Allen Wrench
• Center punch
• Drill
• Flat tip screwdriver
• Phillips screwdriver
• Pencil
Preparing the Stile
NOTE: Figure 1, “Rivnut Installation for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset,
Single Lever,” and Figure 2, “Rivnut Installation for 1-1/2” [38.1 mm] Backset, Single
Lever,” provide illustration for the following steps.
1. IF using a 1-1/8” [28.58 mm] backset,
THEN MARK a vertical reference line 5/32” [3.97 mm] behind the backset centerline.
2. APPLY the stick-on template over the cylinder backset centerline reference 5/32” [3.97 mm]
offset to clear the stop on the frame for a 1-1/8” [28.58 mm] backset.
3. CENTERPUNCH all holes.
4. DRILL holes at center punch locations.
5. REMOVE the template.

3 80-0180-418, Rev D
Figure 1. Rivnut Installation for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset, Single Lever
Figure 2. Rivnut Installation for 1-1/2” [38.1 mm] Backset, Single Lever
Inches [Millimeters]

4 80-0180-418, Rev D
Offsetting the Escutcheon for 31/32” [24.61 mm] and
1-1/8” [28.58 mm] Backset
1. LOOSEN the two #4-40 x 1/4” flat head screws securing the adjustable cover on the back of
the trim cartridge until the cover can be slid (see Figure 3, “Adjustable Cover and Trim
Cartridge”).
2. PUSH the adjustable cover toward the nose edge of the door until it stops (see Figure 3).
3. TIGHTEN the two #4-40 flat head screws to secure the adjustable cover in place.
Figure 3. Adjustable Cover and Trim Cartridge
Optional Monitoring Switch
NOTE 1:Monitored trim contains an internally mounted switch (see Figure 4, “Optional Monitor
Switch”), secured with two M1.6 x .35 mm Phillips pan head screws. The switch is
activated when the handle is rotated to the UNLOCK position.
NOTE 2: All unused leads from the monitor switch must be terminated.
Figure 4. Optional Monitor Switch

5 80-0180-418, Rev D
1. WIRE the optional monitor switch in accordance with Table 1, “Wire Colors and Maximum
Switching Current,” and Figure 5, “Example Wiring Diagram with N.O. Monitoring.”
Table 1. Wire Colors and Maximum Switching Current
Wire Color Label
Black Common Contact
White Normally Open Contact (N.O.)
Red Normally Closed Contact (N.C.)
Maximum Switching Current
(choose N.O. or N.C. for monitoring) 0.1A at 125 VAC/30 VDC
Figure 5. Example Wiring Diagram with N.O. Monitoring
Installing Trim to Stile
1. INSTALL rivnuts.
2. INSTALL the 4581 Cam Plug into the 4300, 4500, or 4900 deadlatch, and SECURE with the
set screw on the latch.
3. INSERT the drive spindle into the trim body prior to mounting.
4. MOUNT the cover plate (not required for 1-1/2” backset) and the trim body to the stile using
two #10-32 x 7/8” flat head screws.
5. SLIDE the cover onto the trim body from the top.
NOTE: The groove on the shaft faces opposite to the latch bolt.
6. INSERT the shaft through the hole on the cover and the output on the trim body.
7. TIGHTEN the set screw with a 3/32” Allen wrench to secure the shaft (see Figure 6,
“Installing Trim to Stile”).
8. INSTALL the top cap using two #4-40 x 1/4” flat head screws (see Figure 6).
9. PUSH the cover up flush with the top cap, and INSTALL the bottom cap using a #6-32 x 1/4”
flat head screw (see Figure 6).

6 80-0180-418, Rev D
Figure 6. Installing Trim to Stile
Installing the Handle
1. INSERT washer and then INSERT hub
over the shaft, as required (see Figure 7,
“Installing the Handle”).
Figure 7. Installing the Handle
2. INSTALL the handle over the hub with the
hole aligned with the hole on the hub (see
Figure 7).
NOTE: The shaft detent should be aligned
with the locking screw.
3. SLIDE the handle in until it rests against
the trim cover.
4.
Using a 1/8” Allen wrench, TIGHTEN the
lock screw to secure the handle to the
shaft (see Figure 7).

7 80-0180-418, Rev D
Determining and Changing the Handing Configuration
1. DETERMINE the current handing configuration(see Figure 8, “Handing Configuration”).
Figure 8. Handing Configuration
NOTE: During the next step, it is necessary to hold the monitor slide down to keep it from
popping out of place by the slide return spring.
1. IF a change of handing is required,
THEN PERFORM the following.
a. REMOVE both #4-40 x 1/4” screws and REMOVE the cover (see Figure 8).
b. REMOVE and FLIP the direction rack, ensuring the drive gear stays in position (see
Figure 8).
c. INSTALL cover.
d. SECURE cover using the two #4-40 x 1/4” screws
Changing the Handing of the 4581 Cam Disc
NOTE: Figure 9, “Changing the Handing of the 4581 Cam Disc,” provides an overall view for
the steps in this section.
Figure 9. Changing the Handing of the 4581 Cam Disc

8 80-0180-418, Rev D
1. DEPRESS the rear push cap.
2. While holding the rear push cap, SLIDE
the eagle beak cam down and out of
the front push cap and the dowel pin.
3. FLIP the eagle beak cam to the other
side, and SLIDE it in the dowel pin and
up to the front push cap.
4. Release the rear push cap to complete
the changing hand operation.
© 2015, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company.