Assa Abloy Sargent 10G13 User manual

INSTALLATION INSTRUCTIONS FOR
10 Line Lever Lock (Patents Pending)
For installation assistance, contact SARGENT at 800-727-5477
www.sargentlock.com
Door Preparation
IMPORTANT:
Fold template onto high
edge of door bevel
38" fr
om
Finished Floor
Template
Door
Bevel
DOOR
FRAME
Backset
must match lock
(2-3/8" or 2-3/4")
• All doors should be properly reinforced for lock support. If support is not provided, contact door manufacturer.
• For all metal door preparations use template A4375, EXCEPT for functions 10G70 or 10G71 which uses template 4409
(provided), or functions 10U93, 10U94 and 10U94-2 which require template A4375.
• For all wood door preparations use template A6719, EXCEPT for functions 10G70 & 10G71 which uses template 4409
(provided), or functions 10U93, 10U94 and 10U94-2 which requires template A4375.
• Template information is available on our website, [email protected].
Strike
IMPORTANT: Deadlocking latch must
stop on strike when door is closed
© SARGENT Manufacturing Company A7133J
• Final Door Prep • Frame Prep for Strike
12
34
56
7
8
4
2
9
10 11
12
13
14
16
17
15
Parts
1. Inside lever
2. Scalp (2)
3. Screws – mounting plate
(2) #6 x 3/4” self-tapping
4. Spacer bushing (2)
5. Inside rose assembly
6. Screws – through-bolt
(2) #10-32 x 1-1/4”
7. Lockbody
8. Outside rose assembly
9. Cylinder spacer
Tools
#2 Phillips screwdriver
Push pin (provided)
7/16” drill bit
1/8” drill bit
2-1/8” bore
1” bore
1
10. Cylinder
11. Outside lever
12. Key
13. Push pin
14. Latch
15. Screws – latch & strike
(4) #8-32 x 3/4”
16. Strike
17. Strike box
Screws (2)
#8-32 x 3/4"
Centerline of
latch front and
strike
Outside of Door
(secured side)
Inside of Door
• Mark and Drill Holes
2-1/8"
(54mm)
hole
5/32"
(4mm)
1-1/8"
(29mm)
2-1/4"
(57mm)
7/16" (11mm) hole
1"
(25mm)
hole
* Used with 68 Function only

Preset LockLatch Installation
Door
frame
2-FRONT
Screws (2)
10-32 x 1-1/4"
Screws (2)
#6 x 3/4"
Scalp to be removed with flat
bladed screwdriver at notch
Test
for proper
operation
before
closing
door
Through-bolt
holes
Mounting plate
with through-bolts
Spacer bushing
2A
3
1
Preset thrubolt locations –
for different locations see
instructions to the right
Outside
of Door
Preset thrubolt locations –
for different locations see
instructions to the right
Outside
of Door
2
Install loosely;
tighten after step #3
Screws (2)
#8-32 x 3/4”
Please note: Doors without a beveled edge need to be
adjusted to center the latch - adjust per step 2A.
Outside
of Door
1-3/4" thick door
2" thick door
•Through-bolt Location – 12 and 6 o’clock
•Door Thickness – 1-3/4” thick
• See Step 2A for other door conditions
A7133J © SARGENT Manufacturing Company
2
• Remove – outside lever (usually keyed), scalp and spacer bushing
• Rotate – mounting plate to either align with through-bolt holes in door
or adjust for proper door thicknesses (see markings on through-bolt)
• Reinstall – spacer bushing (to align with back of lever), scalp and lever
Through-bolt and door thickness adjustment other than preset

Lever and Cylinder Removal
Standard Cylinder Installation
Interchangeable or Removable Core Installation
Rotate key 45ϒ
and hold
Depress lever retainer
with push pin tool
Control key*
C
Rotate key 45ϒ
and hold
Depress lever retainer
with push pin tool
Control key*
C
Remove/Reuse
6 Pin Tailpiece
Plastic Core
Construction
Core
7-pin –
in box
6-pin –
in core
Keyed
Cylinder
Keyed
Cylinder
C
New Cylinder
Washers
(only 30-prefix)
Cylinder
Outside
lever
Key
Cylinder
spacer
IMPORTANT:
Before cylinder installation 10G16, 10G30,
10G37, 10G38 and 10G54 functions
lock, must be timed/preset by rotating
cam (within the the lever support tube)
completely counterclockwise.
• Remove cylinder and tailpiece, using
control key (stamped “C”)
• Insert Phillips #2 screw driver into
cylinder opening making contact with
lever retainer.
• Pull lever retainer horizontally towards
door hinge and remove lever.
*Note- 1 Bitted cylinders utilize a control
key cut 113511
4
Correct key orientation
during assembly
• IMPORTANT:
Remove tailpiece from construction
core and insert into new cylinder
• Install Cylinder
Insert cylinder with control key (stamped “C”)
into lever; rotate 15 degrees and remove key
• Remove construction core
or plastic core
If keyed – use Control Key
(stamped “C”) rotate 15
degrees and pull
Remove/Reuse
6 Pin Tailpiece
Plastic Core
Construction
Core
7-pin –
in box
6-pin –
in core
Keyed
Cylinder
Keyed
Cylinder
C
New Cylinder
Remove/Reuse
6 Pin Tailpiece
Plastic Core
Construction
Core
7-pin –
in box
6-pin –
in core
Keyed
Cylinder
Keyed
Cylinder
C
New Cylinder
Remove/Reuse
6 Pin Tailpiece
Plastic Core
Construction
Core
7-pin –
in box
6-pin –
in core
Keyed
Cylinder
Keyed
Cylinder
C
New Cylinder
Remove/Reuse
6 Pin Tailpiece
Plastic Core
Construction
Core
7-pin –
in box
6-pin –
in core
Keyed
Cylinder
Keyed
Cylinder
C
New Cylinder
C
Remove
Construction
Core
Install
New/Final
Cylinder
© SARGENT Manufacturing Company A7133J 3
Lever retainer
Standard Cylinder
Interchangeable and Removable Core Cylinder

Install 10U94/10U94-2
Remove 10G13
A7133J © SARGENT Manufacturing Company
4
• Remove inside (non-rigid) lever with standard
push pin
• Insert long push pin into inside lockbody tube
and push to release spring loaded lever catch
plug assembly for the outside lever
• Remove the outside lever with lever catch plug
assembly attached
• Power Required: 24Volt DC, .25 amps,
wiring information provided
• Wires must be protected from
abrasion
• Important- See correct door template
4409 provided or on the
website at [email protected].
Function Description:
10G70 Fail Secure
Power OFF unlocks outside lever
Power ON locks outside lever
Key retracts latch at all times
10G71 Fail Secure
Power ON unlocks outside lever
Power OFF locks outside lever
Key retracts latch at all times
2-FRONT
Screw
1/4 x 20 Cup
washer
Screws (2) #6 x 3/4"
Scalp to be removed
with flat bladed screwdriver
2 holes to align with
2 tabs on rose
Rose
Install 10U93
Install 10G70 & 10G71
Screw
1/4 x 20
Cup
washer
Backset
1-1/8" 1/8" x 3/16" deep
Hole
5/16"
dia.
Screws (2) #6 x 3/4"
Scalp to be removed
with flat bladed screwdriver
Screws (2) 10-32 x 1-1/4"
Screws (2)
#8-32 x 3/4"
Tab
2 holes to align with
2 tabs on rose
Rose