Assa Abloy Yale YDME 50 Pro User manual

User’s Guide
YDME 50 Pro
What's Inside the box :
1 Front Panel, 1 Back Panel, 1 Lock Body,
1 Cylinder, 1 Strike Plate, 1 User Manual,
2 Keys, 2 RFID Cards, 1 Installation Template,
Fixing Screws, 4 AA Batteries
*Charges Extra I Visit www.yalehome.co.in for Warranty/Term & Conditions

.
.
DESCRIPTION
Please keep internal/external panel clean before installation.
2 3
Change Handle Direction
Lock Body Change Direction Lock Body and Gusset plate Installation
Handle Alignment
Outside Panel Accessory
The triangle arrow of clutch
wheel should face downwards
Reversing stop piece
Oblique Latch
Screw
Gusset
Plate Box Lock Body
Square Latch
Handle change
direction screw
Install the door buckle plate on the door frame
directly opposite the lock body. The hole of the
buckle plate shall correspond to the tongue of
to the lock body. If there is any deviation, it must
be adjusted to the appropriate position.
Use 2 screws to tighten lock body on frame and
make sure lock body and door panel are parallel
Fingerprint wire should
always follow handle direction
Inside Panel Accessory
When installing lock body - Oblique latch
should always be on top while square latch
should at bottom. Oblique should face door
closing way otherwise it has to be adjusted.
Post this follow below steps:
1) Turn reverse stop unit upwards
2) Push in oblique latch and turn 180
degrees
3) Take out oblique latch
Battery Cover
Screw Hole
Battery cover
Reset Button
Inside Handle Front Handle
Lock Switch
Screw Hole
Body Cover
Keypad
RFID Scanner
Emergency Power Slot
Manual Key

.
Product Features:
● Multiple ways to access: Pin Code, RFID Card & Mechanical Key.
● Pin code: Elegant keypad with code scrambling feature. User can input random
digits before actual code to avoid password peeping as lock supports code
scrambling function.
● Dual authentication mode: After this setting dual authentication will be required to
access the lock at same time to open the door, suitable for high security access.
Dual authentication can be two RFID Cards or two pin codes. These can also be
a combination of any two accesses from Pincode or RFID Card.
● Master has the right to make different users. Lock can have 9 master users (can
be pin code or card). Total user capacity is 250
● Alarm: Tamper, low battery alarm and password protection.
● Lock will sound alarm in case of tampering with door or lock, when battery is low
or when repeatedly wrong password is used.
Remarks:
4 5
1. After installation of lock please reset lock to factory default mode.
2. Handle is the key part for opening and closing door, and its flexibility ratio
directly influences the usage of door lock, hence, don't hang articles on handle.
3. This lock uses 4 AAA high-energy alkaline batteries (1.5V). When it prompts "the
voltage is low, please replace battery" for the first time, the door can be opened
for about 100 times as per different battery capacities; At this time, the battery
should be replaced promptly to avoid inconvenience due to the exhausted
battery.
4. After continuous 5 times wrong card or code usage lock will be locked for 90
seconds.
1. Reset factory default: Press RESET at back of lock for 5 seconds, voice
will prompt reset succeed.
2. Lock Settings:
2.1 Administrator Settings: Touch screen keypad for lights on and press
# for 2 seconds, and press 1 for Administrator settings.
Press 1 again for addition of Master User.
• RFID Card: Scan RFID card in front of RIFD Scanner. After
successful addition, voice prompts “1X1X Successful”.
• Pin Code: Enter 8 Digit Pin Code -> Press # -> Repeat
Pin Code-> Press#
After successful addition, voice prompts “1X1X Successful”.
To go back to the main menu press *
Press 2 for Deletion of Master User.
• System will prompt “ Please input number”
Please input respective user number “1X1X” to delete
• Press # to confirm
Operations:
•
Installation Layout
Connection screw
Connection screw
Lock Body
Inside Panel Accessory
Outside Panel Accessory
Spindle

Please keep a record of Serial number of registered user which would be
helpful in case of individual user has to be deleted at a later stage.
2.2 User Settings:
Press 1 again for User Addition
• RFID Card: Scan RFID card in front of RIFD Scanner. After
successful addition, voice prompts “1X1X Successful”.
• Pin Code: Enter 8 Digit Pin Code-> Press # -> Repeat Pin Code->
Press #
After successful addition, voice prompts “1X1X Successful”.
To go back to the main menu press *.
• Press 2 for User Deletion
• System will prompt “ Please input number”.
• Please input respective user number “1X1X” to delete.Press # to
confirm.
2.3 System Settings: Touch screen keypad for lights on and press # for 2
seconds, and Voice prompts “Please input administrator input”. Verify the
administrator access verification and press 3 for System settings.
• Press 1 for Voice Settings
Press 1 to turn on the volume
Press 2 to turn off the volume
To go back to the main menu press *
Press 2 for Unlocking Mode
• Unlock Mode means to allow opening of lock by single or dual authentication.
In Single authentication, any single authorized user can open the lock,
however in Combination Unlock access credentials of two authorized users
are required for lock opening.
• Press 1 for Single Unlocking Access
Press 2 for Dual or Combination Unlock
To go back to the main menu press *
Press 3 for Language Settings
• Press 1 for selecting Chinese Language
• Press 2 for selecting English Language
To go back to the main menu press *
Press 4 for Time Settings
• Lock will share current time updated on the lock
• To Change enter new date & time in the format YYYYMMDDHHMM
and press #,
where YYYY represents Year, MM- Month, DD- Date, HH- Hour &
press #,
where YYYY represents Year, MM- Month, DD- Date, HH- Hour & MM
Minutes.
To go back to the main menu press *
Press 5 for Lock Number Modification
• Lock Number means number assigned by you to a particular lock if you
have installed multiple locks at your place.
• Lock will share current assigned number.
• To Change enter new lock number (4 Digits) & press #. Lock will
prompt new number for confirmation.
To go back to the main menu press *
2.4 Reboot System: Touch screen keypad for lights on and press # for 2
seconds, and Voice prompts “Please input administrator input”. Verify the
administrator access verification and press 4 for System Reboot.
• Lock will ask to authorize administrator access.
• After successful verification of administrator password- lock will reboot
itself and prompt initialization successful.
1. Password is of 8 digits and has to be entered 2 times for addition.
2. Card is registered after voice prompts "add user" & scan card near
RFID scanner for confirmation.
3. After successful registration press * to exit.
6 7
Important Instructions:
Important Instructions
•
•
•