AXIOMTEK eBOX635-881-FL-i7-4770TE User manual

eBOX635-881-FL Series
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2016 Axiomtek Co., Ltd.
All Rights Reserved
June 2016, Version A5
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The eBOX635-881-FL does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the eBOX635-881-FL before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the eBOX635-881-FL is properly grounded.
4. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen.
6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -40℃or above 80℃. It may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static electricity
on your body.
When handling boards and components, wear a wrist-grounding strap, available from
most electronic component stores.
Classification
1. Degree of production against electric shock : not classified
2. Degree of protection against the ingress of water : IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air
or with oxygen or nitrous oxide.
4. Mode of operation : Continuous

iv
General Cleaning Tips
You may need the following precautions before you begin to clean the computer. When you
clean any single part or component for the computer, please read and understand the details
below fully.
When you need to clean the device, please rub it with a piece of dry cloth.
1. Be cautious of the tiny removable components when you use a vacuum cleaner to
absorb the dirt on the floor.
2. Turn the system off before you start to clean up the component or computer.
3. Never drop the components inside the computer or get circuit board damp or wet.
4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of
cleaning. Some individuals may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the computer.
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
your computer and peripherals users can also use household items to clean their computers
and peripherals. Below is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be able to be cleaned using a
product designed for cleaning that component, if this is the case it will be mentioned in the
cleaning.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend you
to rub it with a piece of cloth.
Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or
rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the
plastics parts.
Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of
a computer can be one of the best methods of cleaning a computer. Over time these
items can restrict the airflow in a computer and cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools
for wiping hard to reach areas in your keyboard, mouse, and other locations.
Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs.
Note: We strongly recommended that you should shut down the system before you start
to clean any single components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable

v
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well, please
contact your Axiomtek distributor for recycling and we will make the proper arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines
Corporation.
Intel® , Core™and Pentium® are registered trademarks of Intel Corporation.
MS-DOS and Microsoft® are trademarks of Microsoft Corporation.
Windows 7, Windows8, Windows 10, Windows 7 Embedded, Windows 8 Embedded,
Linux, MS-DOS, Microsoft® and other brand names and trademarks are the
properties and registered brands of their respective owners.

vi
Table of Contents
Disclaimers.............................................................................................................. ii
Safety Precautions................................................................................................. iii
Classification.......................................................................................................... iii
General Cleaning Tips ........................................................................................... iv
Scrap Computer Recycling..................................................................................... v
CHAPTER 1 INTRODUCTION ........................................................................1
1.1 General Description............................................................................ 2
1.2 System Specifications........................................................................ 3
1.2.1 CPU .................................................................................................................... 3
1.2.2 I/O System ......................................................................................................... 3
1.2.3 System Specification........................................................................................ 3
1.2.4 Driver CD Content............................................................................................. 4
1.3 Dimensions ......................................................................................... 5
1.3.1 System Dimension............................................................................................ 5
1.3.2 Wall mount Dimension..................................................................................... 6
1.4 I/O Outlets ........................................................................................... 7
1.5 Packing List......................................................................................... 8
1.6 Model List............................................................................................ 9
CHAPTER 2 HARDWARE INSTALLATION..................................................11
2.1 Installing the 2.5” SATA Device ....................................................... 11
2.2 Installing the Memory Module.......................................................... 12
2.3 Installing the CFast™ ....................................................................... 16
2.4 Installing the Express Mini Card...................................................... 17
2.5 Installing CPU and PCH Thermal Pad.............................................. 19
CHAPTER 3 JUMPER SETTING & CONNECTORS ....................................21
3.1 SBC Placement ................................................................................. 21
3.2 Jumper Settings and Connectors.................................................... 23
3.2.1 CMOS Clear Jumper (SJP2 on SBC87881)................................................... 24
3.2.2 DC Power In Connector (SCN1)..................................................................... 24
3.2.3 Digital Input Connector.................................................................................. 24
3.2.4 Digital Output Connector............................................................................... 25
3.2.5 VGA Connector ............................................................................................... 26
3.2.6 DisplayPort Connector................................................................................... 26
3.2.7 HDMI Connector (SCN6-SCN7)...................................................................... 27
3.2.8 USB 3.0 Connector (SCN10) .......................................................................... 27
3.2.9 USB 2.0 Connector (SUSB1 and SUSB2)...................................................... 28
3.2.10 COM1~COM6 Serial Port Connector............................................................. 28
3.2.11 Audio Connector............................................................................................. 28
3.2.12 Ethernet Connector (LAN1~LAN2) ................................................................ 29
3.2.13 ATX Power On/OFF Button............................................................................ 29
3.2.14 Reset Button.................................................................................................... 29
3.2.15 Remote Power Switch Connector (SPWRBT1)............................................ 29
3.2.16 AT/ATX Switch................................................................................................. 30

vii
3.2.17 Serial ATA Connectors (SATA1-SATA2)....................................................... 30
3.2.18 SIM Card Slots (SCN19).................................................................................. 30
3.2.19 CFast™ Socket................................................................................................ 31
3.2.20 Half-Size Express Mini Card Slot (SCN13) ................................................... 32
3.2.21 Full-Size Express Mini Card (w/ SIM Slot)/ mSATA (SCN14)...................... 33
3.2.22 Power Output Connector (SCN22, SCN26)................................................... 34
CHAPTER 4 AMI BIOS SETUP UTILITY......................................................35
4.1 Starting.............................................................................................. 35
4.2 Navigation Keys................................................................................ 35
4.3 Main Menu......................................................................................... 36
4.4 Advanced Menu................................................................................. 37
4.5 Chipset Menu .................................................................................... 48
4.6 Boot Menu ......................................................................................... 52
4.7 Security Menu ................................................................................... 53
4.8 Save & Exit Menu.............................................................................. 54
APPENDIX WATCHDOG TIMER..................................................................57
About Watchdog Timer .................................................................................... 57
Assembler Sample Program............................................................................ 58

viii
This page is intentionally left blank.

eBOX635-881-FL Series User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the eBOX635-881-FL.
The Chapter 1 includes the following sections:
General Description
System Specifications
Dimensions
I/O Outlets
Packing List
Model List

eBOX635-881-FL Series User’s Manual
Introduction
2
1.1 General Description
The eBOX635-881-FL is an embedded system that supports LGA1150 Socket 4th
generation Intel® Core™ i7/i5/i3/Celeron processor to support Windows 7, Windows
7 Embedded, Windows 8, Windows 8 Embedded Windows 10 or Linux, suitable for
the most endurable operation.
It features fan less design with full feature I/O, one 204-pin unbuffered SODIMM
socket for single channel DDR3-1333/1600 MHz memory, and enhanced system
dependability by built-in Watchdog Timer.
Features
1. Intel® Haswell / Haswell-Refresh H81 Platform
2. Support LGA1150 Socket Intel® Core™ i7/i5/i3/Celeron processor
3. Maximum to 8GB DDR3 1333/1600 MHz memory
4. Compact and fan-less design
5. Supports 2 USB 3.0 ports and 4 USB 2.0 ports
6. Supports 6 jump-less RS-232/422/485
7. Supports 2 10/100/1000Mbps Ethernet ports
8. Supports ATX power switch with status indicator (AT/ATX mode selection)
9. 16 DI/DO (8 IN & 8 OUT)
10. Two HDMI
11. One DisplayPort
12. One VGA
13. One 2.5” SATA HDD drive bay
(Supports 9.5mm height HDD/SSD, power provides +5V to the drive only)
14. One front access CFast™
15. Watchdog timer
16. AC to 19V/12V DC adapter
17. Dual Express Mini Card slot with one SIM slot
18. Three Antenna openings
Reliable and Stable Design
The eBOX635-881-FL adopts the advanced cooling system and supporting the CFast™,
which makes it especially suitable for vibration environments, best for industrial
automation, digital signage and gaming application.
Embedded O.S. Supported
The eBOX635-881-FL not only supports Windows 7, Windows 8, Window 8.1, and
Windows 10, but also supports embedded OS, such as Windows 7 Embedded, Windows
8 Embedded and Linux.
Various Storage devices supported
For storage device, the eBOX635-881-FL supports one 2.5" SATA storage drive bay,
mSATA and one CFast™ slot.

eBOX635-881-FL Series User’s Manual
Introduction
3
1.2 System Specifications
1.2.1 CPU
CPU
LGA1150 Socket Intel® Core™ i7/i5/i3/Celeron processor
Working temperature depends on TDP of processor, please refer to 1.2.3
System Specification
Chipset
Intel® Haswell H81 chipset
BIOS
American Megatrends Inc. UEFI (Unified Extensible Firmware Interface)
BIOS.
System Memory
One 204-pin unbuffered DDR3 1333/1600MHz SO-DIMM socket, max. up
to 8GB
1.2.2 I/O System
Six jumper-less RS-232/422/485. COM1~COM6 for full function 9-pin D-Sub male
connectors
One VGA connector for display (Supports max resolution up to 1920x1200)
One DisplayPort for display (Supports max resolution up to 2560x1600)
Two HDMI for display (Supports HDMI 1.4a, max resolution up to 4K × 2K)
Two Audio connectors (Mic-IN, Line-OUT)
Two RJ-45 connectors for 10/100/1000Base-T Ethernet ports
Two USB 3.0 connectors
Four USB 2.0 connectors
Eight Digital Input and Eight Digital Output for digital I/O 9-pin D-Sub female
connectors
One 19/12V DC-IN Power Input connector
One Indicator for HDD Active
One Reset switch
One AT/ATX switch
One Power switch
One Remote PWR switch
1.2.3 System Specification
Watchdog Timer
1~255 seconds or minutes; up to 255 levels.
Power Supply
19V/12V DC input connector
Operation Temperature
-20℃~50℃(-4 ºF ~ 122ºF), with TDP 35W
Storage Temperature
-40℃~ 80℃(-4 ºF ~ 176ºF)
Humidity
10% ~ 90% (non-condensation)

eBOX635-881-FL Series User’s Manual
Introduction
4
Vibration Endurance
3Grm w/ CFast™(5-500Hz, X, Y, Z directions)
Weight
2.5 kg (5.51 lb) without package
4.5 kg (9.92 lb) with package
Dimensions
280mm(11.02”) (W) x150mm(5.91”) (D) x 76mm(2.99”) (H)
1.2.4 Driver CD Content
Driver
Audio
Chipset
Ethernet
Graphic
Intel Rapid Storage Technology
USB 3.0
ME 9.0
TPM
Manual
User Manual
Quick Manual
Note: All specifications and images are subject to change without notice.

eBOX635-881-FL Series User’s Manual
Introduction
5
1.3 Dimensions
The following diagrams show you dimensions and outlines of the eBOX635-881-FL.
1.3.1 System Dimension

eBOX635-881-FL Series User’s Manual
Introduction
6
1.3.2 Wall mount Dimension

eBOX635-881-FL Series User’s Manual
Introduction
7
1.4 I/O Outlets
The following figures show you I/O outlets on front view of the eBOX635-881-FL.
Front View drawing
Note: If you set AT/ATX switch to AT mode, the system will be automatically
power on without pressing soft power button during power input. If you set
AT/ATX switch to ATX mode, it is necessary to manually press soft power
button to power on the system.
Rear View drawing
Power Button
Remote Switch
USB 2.0
COM1~COM6
(RS232/422/485)
Audio Connectors
(Mic-IN, Line-
OUT)
LED
Indicator
HDD State
AT/ATX Switch
Reset
DC Input- 19/12V
Antenna opening
Display Port
Gigabit Ethernet
LAN1/2
CFast™slot
USB 2.0
VGA
Antenna opening
DI/DO
(8 IN & 8 OUT)
HDMI 1&2
USB 3.0

eBOX635-881-FL Series User’s Manual
Introduction
8
1.5 Packing List
The package bundled with your eBOX635-881-FL should contain the following items:
eBOX635-881-FL System Unit x 1
eBOX635-881-FL Quick Installation Guide x 1
AC to 19/12V DC adapter (By selection)
CD x 1 (For Driver and Manual)
Screws Pack x1
DRAM Thermal pad
Spare parts: CPU, PCH of thermal pad
Pre-install Intel Processor
Pre-install Foot pad x4
Optional DDR3 SODIMM
Optional Wall-mount Brackets
Optional Antenna
Optional Mini Card Module
Optional 2.5”SATA Storage
Optional CFast™Card
Optional Power Cord
Note: If you can not find this package or any items are missing, please contact
Axiomtek distributors immediately.

eBOX635-881-FL Series User’s Manual
Introduction
9
1.6 Model List
eBOX635-881-FL-i7-4770TE
Fanless Embedded System with Intel Core i7-4770TE (4 Cores)
2.3G, max. up to 3.3G Processor, HDMIx2/VGA,DisplayPort,
GbE LAN*2, USB3.0*2, Audio, RS-232/422/485*6, DI*8/DO*8,
19/12V AC/DC Power Adapter
eBOX635-881-FL-i5-4570TE
Fanless Embedded System with Intel Core i5-4570TE (2 Cores)
2.3G, max. up to 3.3G Processor, HDMIx2/VGA, DisplayPort,
GbE LAN*2, USB3.0*2, Audio, RS-232/422/485*6, DI*8/DO*8,
19/12V AC/DC Power Adapter
eBOX635-881-FL-i3-4330TE
Fanless Embedded System with Intel Core i3-4330TE (2 Cores)
2.4G Processor, HDMIx2/VGA, DisplayPort, GbE LAN*2,
USB3.0*2, Audio, RS-232/422/485*6, DI*8/DO*8,19/12V AC/DC
Power Adapter
eBOX635-881-FL-G3320TE
Fanless Embedded System with Intel Pentium G3320TE (2
Cores) 2.3G Processor, HDMIx2/VGA, DisplayPort, GbE LAN*2,
USB3.0*2, Audio, RS-232/422/485*6, DI*8/DO*8,19/12V AC/DC
Power Adapter
If you cannot find this package or any items are missing, please contact Axiomtek distributors
immediately.

eBOX635-881-FL Series User’s Manual
Introduction
10
This page is intentionally left blank.

eBOX635-881-FL Series User’s Manual
Hardware Installation
11
CHAPTER 2
HARDWARE INSTALLATION
The eBOX635-881-FL is convenient for your various hardware configurations, such as HDD
(Hard Disk Drive), SSD (Solid State Drive) CFast™card or PCI Express Mini Card modules.
The chapter 2 will show you how to install the hardware.
2.1 Installing the 2.5”SATA Device
Step 1 Turn off the system, and unplug the power cord.
Step 2 Turn the system upside down to locate screws at the Bottom, loosen screws.
Step 3 Remove the cover and then loosen four screws of 2.5”HDD drive bay.
Step 4 Assembly your 2.5”HDD/SSD into drive bay, fasten it with four screws.

eBOX635-881-FL Series User’s Manual
Hardware Installation
12
Step 5 Please refer to the following photo to connect SATA power and signal cables.
Step 6 Fasten screws of HDD drive bay.
2.2 Installing the Memory Module
Step 1 Turn off the system, and unplug the power cord.
Step 2 Turn the system upside down to locate screws at the Bottom, loosen screws.
Step 3 Remove the bottom cover to locate the bracket screws. Then loosen four
screws to take out the bracket directly.