Ballard Designs Edith Desk with Hutch MO606 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
Page 1 of 6
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 3-15-2021
PRODUCT NAME: Edith Desk with Hutch
ITEM NUMBER: MO606
ASSEMBLED DIMENSIONS : 40 3/4”H x 56 1/2”W x 27”D
MADE IN CHINA
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 6
Ltr.
A 18
B 2
Qty. Hardware Included
Ltr.
H
J
1
1
Qty. Components
C20
REQUIRED TOOLS:
Allen Wrench (included),
Phillips Screwdriver
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
D
E
F
20
1
2
Small Allen Bolts
1/4” x 5/8”
Large Allen Bolts
1/4” x 1”
Lock Washers
Flat Washers
Allen Wrench
Wall Anchoring
(Anti-tip) Kits
See page 5
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
G
I
Cleaning and Care
Periodically dust with a soft, dry cloth.
Protect surfaces to prevent damage.
Do not use alchohol based cleaners or polishers.
K
1
1
1
Top (G)
Right Frame (H)
Left Frame (I)
Back Frame (J)
Front Frame Connector (K)
L
M
N
1
1
1
Hutch (L) Left Hutch
Frame (M)
Right Hutch
Frame (N)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.

E
A
C
D
Page 3 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Orient Left Frame (I) and Right Frame (H) as illustrated with Connector Tabs on edge near floor
then attach Front Frame Connector (K) to each side using Small Allen Bolt (A) with Lock Washer (D) and
Flat Washer (D). Fully tighten using Allen Wrench (E).
Connector Tabs
(I) (H)
(K)
STEP 2: Orient Back Frame (J) as illustrated with Connector Tabs on top edge, opposite Legs. Attach to
tabs at top and bottom using Small Allen Bolts (A) with Lock Washer (C) and Flat Washer (D). Use Large
Allen Bolts (B) with Lock Washer (C) and Flat Washer (D) to further secure Back Frame to both Left and
Right Frames. Fully tighten all Bolts using Allen Wrench (E).
E
A
C
D
EBCD
(J)
Connector Tabs
Assemble in location for intended use.

Page 4 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(G)
STEP 4: Orient Connector Tabs on both Left Hutch Frame (M) and Right Hutch Frame (N) with holes in
Left and Right Frames (I,H) and attach to assembled Desk using Small Allen Bolt (A) with Lock Washer
(C) and Flat Washer (D). Fully tighten using Allen Wrench (E).
E
A
C
D
(M)
(N)
(I)
(H)
Assemble in location for intended use.
STEP 3: Carefully orient Top (G) as illustrated with drawers fronts facing upward. Align holes in Top
with those in Connector Tabs on upper edge of Frame Assembly. Attach using Small Allen Bolt (A) with
Lock Washer (C) and Flat Washer (D). Fully tighten using Allen Wrench (E).
E
A
C
D

STEP 6: Drawer Pulls ship attached to inside of each drawer. Use a Phillips Screwdriver to remove
screws and reverse each Pull. Reattach and fully tighten.
E
A
C
D
(M)
(N)
(L)
Page 5 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.
STEP 5: Orient Hutch (L) with Left Hutch Frame (M) and Right Hutch Frame (N) as illustrated. Align
holes and attach using four Small Allen Bolts (A) with Lock Washer s(C) and Flat Washers (D). Fully
tigthen using Allen Wrench (M).

(B)
(A)
(C)
(C)
(D)
Ltr.
A2
Small Screw
Retention Belt
Qty. Hardware Included
B2
Large Screw
C4 Bracket
D2
ANCHORING HARDWARE (ANTI-TIP)
1. Locate and mark a Wall Stud behind Desk at location for installation.
2. Corresponding to Stud location, attach one Bracket (C) to back of Desk using Small Screw (B).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screw (A) 2 inches below Bracket attached to back of console.
4. Move Console into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Page 6 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
WALL
STUD
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING