Ballard Designs JC152 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 12-7-2021 Page 1 of 5
PRODUCT NAME: Madison Poolside Chaise
ITEM NUMBER: JC152
ASSEMBLED DIMENSIONS : 42 1/2”H x 24 3/4”W x 79”L
MADE IN VIETNAM
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 5
REQUIRED TOOLS:
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Ltr.
Left Legs (G)
Cross Bars (H)
Right Legs (I)
Middle Left Leg (J)
Middle Right Leg (K)
Chaise Frame (L)
Back Sling (M)
Back Supports (N)
Seat Supports (P)
Seat Sling (O)
C
D
14
B 4
14
sgulPwercS
01E
s 4mmehcnerWnellA
2F
Qty
Ltr.
G 2
K 1
H 3
N 2
O 1
I 2
J 1
M 1
P 2
stnenopmoC.ytQ
M6x25mm Allen Bolts
A 10
M7x70mm Allen Screws
M6x40mm Allen Bolts
M6x10mm Nuts
L1
Hardware Included
Do not over-torque assembly bolts!
Over tightening may cause wood to crack,
embedded nuts to pull out or other damage.
Avoid power tools. Hand tighten only.
CAUTION
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.

Page 3 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Attach a Left and Right Leg (G,I) to each end of Crossbar (H) using Allen Screws (A). Tighten
using Allen Wrench (F). Repeat process for remaining Left and Right Legs and a remaining Crossbar.
IMPORTANT: Be certain PEG HOLES are identically oriented on both assemblies.
(J)
(I)
(G)
(H)
Peg Hole
(H)
(A)
(A)
(K)
STEP 2: Attach Middle Left and Right Leg (J,K) to each end of remaining Crossbar (H) using Allen
Screws (A). Tighten using Allen Wrench (F).
12
STEP 3: Attach an assembly created in STEP 1 onto each end of Chaise Frame (L) by first fitting peg
holes over pegged ends then inserting Allen Screws (A) and tightening using Allen Wrench (F).
STEP 4: Attach assembly created in STEP 2 to underside middle of Chaise Frame (L) using Allen
Bolts (B) inserted from inside through each Leg and into Frame. Tighten using Allen Wrench (F).
Create End Support Assemblies Create Middle Support Assembly
(G)
(G)
(I)
(A)
(A)
(K)
(B)
(L)
3
4
Attach End Assemblies
Attach Middle Assembly

Page 4 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(O)
(P)
(N)
(M)
STEP 5: Carefully insert each Back Support (N) into pockets along edge of Back Sling (M). Next, insert
each Seat Support (P) into pockets along edge of Seat Sling (O). NOTE: Replacement Slings are
available. Sold separately (Item Number JC157)
5Create Seat and Back Slings
STEP 6: Insert Seat and Back Assemblies (from STEP 5) into channels in Chaise Frame (L). Secure by
inserting Nuts (D) into holes on outside of Frame then inserting Allen Bolt (C) from inside Frame. Insert
one Allen Wrench (F) into Nut and the other Allen Wrench (F) into Bolt then turn and tighten to secure.
Channel
(D)
(C)
(L)
(O & P)
(O & P)
(M & N)
(M & N)
(L)
6Attach Seat and Back Covers

Page 5 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(E)
7Cover Screw Holes
8Adjust Back Angle
STEP 7: Turn assembled Chaise upright and cover screw holes on sides and ends by inserting Screw
Plugs (E) and lightly tapping into place.
STEP 8: Back angle adjustments made by lifting up on back then locking into desired position.
Cleaning and Care
Occasionally wipe or hose down to remove dirt and debris.
Promptly remove spills.
Do not use harsh chemicals or abrasive cleaners.