Ballard Designs Hampton MA265 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 9-6-2022 Page 1 of 7
PRODUCT NAME: Hampton Entry Bench and Hutch
ITEM NUMBER: MA265 (Components MA263 (Bench) and MA264 (Hutch))
ASSEMBLED DIMENSIONS : 80”H x 55 1/2 ”W x 18”D
MADE IN CHINA
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 7
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Ltr.
A 12
B 3
Qty. Included Hardware
Ltr.
D
E
1
1
Qty. Components
C 6
TOOLS NEEDED:
Phillips Screwdriver, Pencil
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
F
4
4
8
I
1
3
G
H
J
K
1
Shelf
Hardware
Shelf Supports
Connector Brackets
Screws
Cam Bolt (2 pcs required)
Cam Lock (2 pcs required)
Wood Dowel (4 pcs required)
NOTE: Assemble furntiure in location for use.
*Back Rail (H) Shelf (K)
*Right Rail (J)
*Left Rail (I)
Bench (G)
*NOTE: For Bench and Hutch unit, Left Rail (I), Right Rail (J) and Back Rail (H) are not used.

Page 3 of 7
REQUIRED TOOLS :
Phillips Screwdriver, Pencil
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
Hardware
LN
M1
Long Screw
L - Bracket
4Short Screws
4
Ltr Qty Included Hardware Ltr Qty Included Hardware
O 1
WARNING
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
Anchoring Hardware Included
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 4 of 7
STEP 1: Bench unit is equipped with Rotary Levelers located under each corner. If necessary, tilt
bench up and turn Leveler clockwise/counterclockwise to adjust.
STEP 2: Join Bench (G) and Hutch (O) as illustrated below. Insert Wood Dowels (F) into pre-drilled
holes in top of Bench and place Cam Bolts (D) into base of Hutch. Insert Cam Locks (E) into
pre-drilled holes on each end of Bench. NOTE: Align Cam Lock so open end is toward hole in top.
This will permit Cam Bolt to enter Lock. Gently lift and lower Hutch onto Wood Dowels and insert Cam
Bolts into Locks. Use a Screwdriver to turn Cam Locks until Cam Bolt is pulled tight and secure.
(F)
(D)
(E)

Page 5 of 7
STEP 3: Further secure Hutch (O) to Bench (G) by attaching Connector Brackets (B) into
pre-drilled holes on back of both units. Use Screws (C) and firmly tighten to secure. See illustra-
tion below for placement.
STEPS 4 through 7 Cover ANTI-TIP ANCHORING HARWARE
STEP 4: Locate and pencil mark Wall Stud(s) in wall behind installation location. Push unit against
wall and postion so that at least one stud located directly behind it.
WARNING
Tip-Over Hazard
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Prevent tipping accidents. Anchor your furniture.
(O)
(G)
(B)
(C)
Wall Stud
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 6 of 7
STEP 5: With unit pushed against the wall, slide L-Bracket (M) over top back of unit and center in
front of Wall Stud. Use a pencil to MARK TOP OF BRACKET.
(M)
STEP 6: Pull unit away from wall and attach L-Bracket (M) at previously marked location using Long
Screws (L). NOTE: It is critical that screws are firmly driven directly into stud. If not, bracket
could be torn from wall in the event of an accidental tip-over.
(M)
(L)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 7 of 7
STEP 7: Slide unit back into place UNDER installed L-Bracket (M) then attach Bracket to top of
Hutch (O) using Short Screws (N). NOTE: Floor molding may prevent Bracket from entirely covering
top. Use Screws only in holes which cover top.
(M)
(N)
(O)
STEP 8: Determine Shelf (K) placement then insert Shelf Supports (A) into pre-drilled holes located
inside Bench (G). Gently lay Shelf onto Shelf Supports.
(A)
(K)
(G)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Cleaning and Care
Periodically dust with a soft, dry cloth.
Protect surfaces to prevent damage.
Do not use alcohol based cleaners or polishers.