Ballard Designs Marloe Glass Shelf WV025 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 4-15-2021 Page 1 of 5
PRODUCT NAME: Marloe Glass Shelf
ITEM NUMBER: WV025
ASSEMBLED DIMENSIONS : 52 1/2”H x 36”W x 12”D
MADE IN INDIA
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 5
Ltr.
A8
B
Qty. Hardware Included
Ltr.
D
E
10
2
Qty. Components
C
4
REQUIRED TOOLS:
Phillips Screwdriver, Pencil,
Level, Drill with 3/8” bit
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Expansion Bolts
(Decorative Bolt and Expanding Sleeve)
Wood Screws
(For attaching directly to Wall Stud)
F
G
H
I
2
4
2
2
2
Cleaning and Care
Periodically dust with a soft, dry cloth.
Protect surfaces to prevent damage.
Do not use alchohol based cleaners or polishers.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
The wall surface must be capable of supporting
the combined weight of the item and any loaded contents;
otherwise, the structure must be reinforced.
SAFETY NOTICE
Lower Brackets (C)
Supports w/SHORT Stud (D)
Supports w/LONG Stud (E)
Glass Shelves (F)
Upper Brackets (G)
Flat Finial (H)
Ball Finial (I)
Avoid Bumping/Impacting Shelf
Sides or Corners
Tempered Glass
Assemble in location for intended use.

Page 3 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
IMPORTANT NOTICE
Shelf unit must be fully assembled BEFORE hanging.
At least two people required to lift, mark and install
assembled shelf. Do not assemble on wall.
STEP 1: Create base by fitting a Glass Shelf (F) over threaded studs on Lower Brackets (C). Secure by
turning Supports with SHORT Studs (D) onto top. Turn until secure. Do not over-tighten.
STEP 2: Add another Glass Shelf (F) then secure with four more Supports with SHORT Studs (D).
STEP 3: Add next Glass Shelf (F) then install both remaining Supports with SHORT Studs (D) on back
side of Shelf as illustrated. Install both Supports with LONG Studs (E) on front of Shelf.
(F)
(D)
(H)
(F)
(D)
(C)
(F)
(D)
12
(F)
(D) (E)
LONG STUDS
on front.
34
STEP 4: Add remaining Glass Shelf (F) then secure back by turning and tightening a Flat Finial (H) onto
top of each Support with SHORT Studs (D). Turn until secure. Do not over-tighten.
(H)
LONG STUD
(G)
(I)
6
(G)
5
STEP 5: Place Upper Bracket (G) onto top by fitting open end over LONG STUD and back end over top
of Flat Finial (H).
STEP 6: Turn and tighten Ball Finial (I) onto LONG STUD. Turn until secure. Do not over-tighten.

Page 4 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 7: Determine location for installation and locate Wall Studs in wall. Optimal support is provided
when one side of Shelf is attached to a Wall Stud. Two or more people lift assembled Shelf to wall
using a Level to adjust. Place on wall and pencil mark ALL HOLES in both top and bottom
Bracket flanges. Remove Shelf from wall and set aside.
WALL STUD
For maximum support, at least one side should
be centered on a WALL STUD.
SAFETY NOTICE
WALL STUD
STEP 8: For hole locations on a WALL STUD, place Shelf on wall and drive Screw (B) directly into
Stud. For those locations where no stud is present, follow instructions on Page 5 for installing and
using Expansion Bolts (A).
Tighten Screws to 75%
DO NOT OVER-TIGHTEN
Two or more people required to complete Steps 7 and 8.
STOP STOP

Page 5 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Drywall
3/8” Drill Bit
Teeth
Barrel
Create Pilot Hole Tap in Bolt until teeth sink into wall surface.
Turn bolt clockwise until it begins to slip. Remove Bolt/Add Bracket/Replace-Tighten
12
34
INSTALLING EXPANSION BOLTS
(C, G)
B
R
A
C
K
E
T
(A)