Ballard Designs Kelley MO512 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 9-1-2022 Page 1 of 4
PRODUCT NAME: Kelley Desk
ITEM NUMBER: MO512
ASSEMBLED DIMENSIONS: 30 1/2”H x 58”W x 30”D
IMPORTED
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 4
Top (J)
Ltr. stnenopmoC.ytQ
Ltr.
C
B
10
2
Qty. Hardware Included
A
8
Left Leg (K)
Right Leg (L)
Stretcher (M)
D8
J1
K1
L1
M1
Assemble in location for intended use.
E
F
G
H
I
REQUIRED TOOLS:
Phillips Screwdriver, Rubber Mallet,
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
Short Bolts
5/16” x18T x1 1/8”
Long Bolts
5/16” x18T x2”
Lock Washers
9/16”
Large Flat Washers
3/4”
2Small Flat Washers
5/8”
1Allen Wrench
2
4
Nuts
Decorative Caps
(2 required / 2 spare)
Wall Anchoring
Anti-tip Kits
See Page 4
2
Hardware Legs
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alchohol based
cleaners or polishers. Promply remove spills.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

(G)(G)
(H)
(E) (C) (B) (F)
(L)
(E)(C)
(B)
(F)
(H)
Assemble in location for intended use.
STEP 1: Remove left and right drawers from Top (J) then invert Top onto a level, padded surface.
Attach Left Leg (K) and Right Leg (L) by inserting Short Bolts (A) with Lock Washers (C) and Large Flat
Washers (D) through hole INSIDE each drawer compartment and into embedded T-nuts in each Leg.
Fully and securely tighten with Allen Wrench (F).
STEP 2: Insert Nuts (G) into holes in each end of Stretcher (M). Orient Stretcher with Nuts facing up
(toward floor when desk is fully installed) then insert Long Bolts (B), Lock Washers (C) and Small Flat
Washers (E) into each end, fully tightening with Allen Wrench (F) to secure each Leg to Stretcher.
Complete by inserting a Decorative Cap (H) into each end covering Bolt heads.
A Rubber Mallet may be needed to gently tap Decorative Caps into place.
Be certain Caps are fully seated and secured. Two spare Caps are included.
Page 3 of 4
(C)(D) (A) (F)
(L) (J) (K)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Installation:
Ltr.
A2
Small Screw
Retention Belt
Qty. Hardware Included
B2
Large Screw
C4 Bracket
D2
WALL ANCHORING HARDWARE (ANTI-TIP)
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screw (B).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screw (A) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
W
A
L
L
S
TUD
WALL BRACKET MUST BE ATTACHED TO WALL STUD
(A)
(B)
(C)
(D)
R
e
presen
t
a
tiv
e
Fu
r
nitu
r
e
I
tem
Page 4 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com