Ballard Designs CANE-BACK DAYBED User manual

CANE-BACK DAYBED
Model #MB091 WWH
Model #MB091 WOO
Model #MB091 GRN
MADE IN CHINA

A
B
C
D
E
F
G
H
I
J
K
L
PARTS LIST
(1) Back Panel
(1) Right Side
(1) Le t Side
HARDWARE LIST
(4) Long Allen Bolts
(12) Spring Washers
(2) Wood Dowels
(4) Wood Plugs
(1) Allen Wrench
(8) Rubber Washers
(8) Short Allen Bolts
(8) Large Metal Washers
(4) Small Metal Washers
C
L
A
SUSPENSION DECK
HARDWARE LIST
(5) Allen Bolts M6 x 56mm
(8) Allen Bolts M6 x 30mm
(1) Allen Wrench
(13) Hex Nuts
(26) Flat Washers
(1) Hex Wrench
PARTS LIST
(2) Bed Frames
(5) Connectors
(4) Frame Plates
A
B
C
D
E
F
G
H
J
L4
J8
I8
H8
HARDWARE LISTQTYNo.
D
E
F
K
4
12
2
1
4
E8
D8
HARDWARE LISTQTYNo.
A
B
4
4
C1
F1
G
G
H
J
B

Parts Bag Located Here
A
E
E
D
H
GG
B
E
E
D
E
D
E
B
G
J
G
G
H
H
H
H
H
G
J
G
J
J
J
This Side Up
This illustration shows
the frame upside down
STEP 1
Begin assembly by attaching each Bed Frame (G) together by
aligning the holes and securing with the 5 Connectors (H). Fit
together and secure in place with 1 Allen Bolt (A), 1 Flat Washer
(E), on the other side 1 Flat Washer (E) & 1 Hex Nut (D).
Tighten all bolts and nuts using the Allen and Hex Wrenches
(C & F) that have been provided.
STEP 2
Attach each Frame Plate (J) to the end o each Bed Frame (G)
by aligning holes and securing with 2 Allen Bolts (B), 2 Flat
Washers (E), on the other side 2 Flat Washers (E) & 2 Hex
Nuts (D). Do not ully tighten bolts and nuts until the Suspension
Deck has been assembled to the daybed.
SUSPENSION DECK
Model #90008 Metal Frame

Parts Bag Located Here
STEP 1
Begin assembly, by irst attaching both Right & Le t Side panels (B & C) to the Back Panel (A), by
inserting each Wood Dowel (F) in place and guiding the panels together, securing with 2 Long Allen
Bolts (D), 2 Spring Washers (E) & 2 Small Metal Washers (L) per each side. Do not ully tighten bolts
or this step.
STEP 2
Attach the Suspension Deck (Now Assembled) to each post on Side Panel (B & C), using 2 Short Allen
Bolts (E), 2 Spring Washers (C), 2 Large Metal Washers (F) & 2 Rubber Washers (G) per each post.
See Figure 3.
STEP 3
Tighten all bolts and nuts rom Page 3 using the hardware provided and care ully insert one Wood
Plug (G) into each hole on the back post o each daybed side to cover Allen Bolt Heads (D) or a total
o our times to complete the assembly.
G
ECF
ECF
B or C
G
FI URE 3
ED
L
ED
L
F
AB
C
G
G