Ballard Designs Trieste SK068 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 7-19-2021 Page 1 of 4
PRODUCT NAME: Trieste 3 Drawer Console Cabinet
ITEM NUMBER: SK068
ASSEMBLED DIMENSIONS : 35”H x 25.75”W x 18.63”D
MADE IN INDONESIA
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 4
Ltr.
A1
B
Qty. Hardware Included
REQUIRED TOOLS:
Phillips Screwdriver, Slotted
Screwdriver (included),
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alcohol based
cleaners or polishers. Promptly remove spills.
Ltr.
G
H
1
2
Qty. Components
Cabinet (G)
Wall Anchoring
(Anti-tip) Kits
(See page 4)
(H)
MOULDING: Attach Base Moulding (H) to
lower sides of Cabinet (G). Omit when joining
multiple Cabinets. Use to cap both open ends
of a multi-cabinet unit.
DRAWERS: To remove, pull fully open. Locate lever
centered within side glides. Lift one lever and push
down on the other and pull drawer out. To replace,
align glides and push drawer completely in.
2
Slotted Screwdriver
For use with Levelers. Retain with Cabinet.
Base Moulding (H)
Lift Lever up on one side and
push lever down on the other.
Lower Drawer must be completely
removed to access Levelers.
C4
D
F2
4
Connector Plates
Allen Bolts
Flat Washers
E1Allen Wrench
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(G)
LEVELERS: Console equipped with Rotary Levelers under
each corner. To adjust, insert Slotted Screwdriver (A) into
fitting INSIDE cabinet and turn to raise or lower corner.
(A)
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
Assemble in location for intended use.

Page 3 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
WARNING: To prevent a dangerous tip-over accident, Cabinets must be secured
together using Brackets as illustrated in this step.
Place Cabinets side by side. Remove Base Moulding (D) from adjoining sides. (Fig. 1) Align side and
back edges then position two Connector Plates (D) as illustrated. Secure using Allen Bolt (A) with Flat
Washer (B). (Fig. 2) Apply Base Moulding to both open ends.
NOTE: Individual Cabinets sold separately.
*INSTRUCTIONS FOR JOINING MULTIPLE CABINETS
Fig. 1
Fig. 2
(E)
(B) (C)
(H)
Use Moulding on open ends.
Omit when joining multiple units.
N
O
T
E
(D)
- If installing optional Hutch (sold separately) please refer to Assembly Instructions included with
Hutch for properly joining all units together using Connector Plates.
- It may be easier to level multiple Cabinets AFTER they’ve been joined together using Connector
Plates.
- Anchor Single and joined Cabinets to wall using Anti-Tip Anchoring Hardware as outlined on Page 4.
- When joining multiple units, there will be leftover/surplus/unused Connector Plates, Bolts, Washers
and Base Moulding.
*PLEASE NOTE
i

Page 4 of 4
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(C)
(B)
(D)
(A)
WALL STUD
WALL ANCHORING HARDWARE (ANTI-TIP)
Ltr.
A4 Small Screw
Retention Belt
Qty. Hardware Included
B4 Large Screw
C4 Bracket
D2
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screws (A).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screws (B) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING