Ballard Designs WS959 WHT 24 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 1/29/2019 Page 1 of 4
PRODUCT NAME: Storage Shelf w/Drawer 24”
ITEM NUMBER: WS959 WHT 24
ASSEMBLED DIMENSIONS: 3”H x 24”W x 7”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN CHINA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 4
Ltr.
D
E
1
1
Qty. Components
HARDWARE PACKET
Two Person Assembly Suggested
REQUIRED TOOLS:
Screwdriver, Pencil, Level and Power Drill
NOTE: To avoid accidentally discarding small
parts or hardware, retain all carton contents until
assembly and installation are complete.
Ltr. Qty. Hardware Included Ltr. Qty. Hardware Included
A
B
C
4
2
4
Wood Screw
Expansion Bolt
Short Screw
Shelf
Bracket
Assemble Shelf near installation location.

Page 3 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Determine location for installation then use level to position Bracket (E) on wall. Mark
screw hole locations with pencil. NOTE: For maximum support, it is preferred to center two
sets of screws over wall studs. If this is not possible, at least one set must be over a stud.
For screws NOT positioned over a wall stud, drill pilot holes and install Expansion Bolts (B).
The Bracket must be secured to the wall in at least two locations with two sets of screws.
Use screwdriver to mount Bracket over marked locations on wall. Use Wood Screws (A)
through Bracket into a stud and Expansion Bolts (B) into drywall. NOTE: At least two
sets of screws must be mounted into a wall stud.
STEP 2:
At least one set of screws (preferably two)
must be secured to a wall stud.
WALL
(E)
(A)
(B)
(B)

Page 4 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: Slide Shelf (D) onto Wall Bracket (E).
Using screwdriver, secure Shelf (D) to Bracket using Small Screws (C) through holes
on underside of Shelf. Firmly secure.
STEP 4:
(D)
(E)
WALL
(D)
(C)
WALL
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as they can damage the finish.
Dust with a soft cloth.

Customer Service: 800-367-2810
Online: www.ballarddesigns.com
UPDATED: 12/28/2015Page 1 of 1
EXPANSION BOLT INSTALLATION:
Note: Expansion Bolts are required when there is not a wall stud to
screw the wood screws into.
TOOLS NEEDED:
-Hammer, Screwdriver,
Level, Pencil, Drill
and 1/4 Drill Bit.
With a screwdriver, press down firmly and turn the bolt clockwise until the barrel crimps against
the inside of the wall and the bolt starts to slip. Unscrew the bolt just enough to allow you to
hang your item.
2
Qty.
Expansion Bolt
Hardware Included
Drywall
Drill Bit
THEN
THEN
Determine the desired height and location for your item. Use a level to ensure the item is perfectly
horizontal. Use a pencil to lightly mark the screw holes onto the wall. Determine if the pencil marks
are located on a stud. If there is no stud, drill a hole through the pencil marks with a 1/4 drill bit.
Lightly tap the Expansion Bolts (A) into the holes and sink the teeth into the wall surface.