Ballard Designs SUZANNE KASLER SK Orleans 48 Round Table User manual

PRODUCT NAME: SK Orleans 48” Round Table
ITEM NUMBER: JC127
DIMENSIONS OF ITEM ASSEMBLED: 30 1/2”H x 48” DIA.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 1/25/2016 Page 1 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN VIETNAM
SUZANNE KASLER
BALLARD DESIGNS

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 6
Ltr.
A
B
8
8
C 4
Qty. Hardware Included
Long Screw
Short Screw
Bolt
Wooden Plug
Allen Wrench
Table Top (F)
Post (H) Support (G)
Arm (I)
Leg (J)
Ltr.
F
G
1
4
Qty. Components
TOOLS NEEDED:
-Assembly may require 2 people.
NOTE: When unpacking, lay the parts
on a padded surface, such as
the packaging provided. Be sure to
locate all hardware before throwing
away any packaging.
D 4
E 2
H 1
I 1
J 1

Page 3 of 6
To assemble the Base, fit the notch of the Leg (J) into the notch in the bottom of the
Post (H). Insert the Long Screws (A) and tighten with the Allen Wrench (E).
STEP 1:
STEP 2:
(A)
(E)
(H)
(J)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Fit the notch of the Arm (I) into the notch in the top of the Post (H). Insert the Long
Screws (A) and tighten with the Allen Wrench (E).
(A)
(E)
(H)
(I)

Page 4 of 6
STEP 3: Position the Supports (G) in place between the Leg (J) and the Post (H). Use the Long
Screws (A) to secure the Supports to the Post. Use the Short Screws (B) to secure the
Supports to the Leg. Tighten all the Screws with an Allen Wrench (E).
(A)
(A)
(B) (J)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(G)
(H)
STEP 4: Position the Supports (G) in place between the Arm (I) and the Post (H). Use the Long
Screws (A) to secure the Supports to the Post. Use the Short Screws (B) to secure the
Supports to the Arm. Tighten all the Screws with and Allen Wrench (E).
(E)
(E)
(B)
(I)
(G)
(H)

(E)
(F)
Page 5 of 6
STEP 5: Insert the Plugs (D) into all the screw holes in the Supports (G). This completes the Base
assembly.
STEP 6: Set the Table Top (F) upside down on a flat, padded surface such as the packaging.
Align the holes in the top of the Base with the holes in the Table Top. Insert the Bolts (C)
and tighten with the Allen Wrench (E). Make sure the bolts are completely tight before
turning the table upright.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(D)
(G)
(C)

Page 6 of 6
STEP 7: If the table is uneven, adjust the five levelers located underneath the Legs (J) and Post (H).
Carefully elevate the table and twist the levelers clockwise and counterclockwise until
the table is even.
Cleaning & Care:
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Please refer to the care instructions on the hang tag.
(J)
(H)