Ballard Designs Stephanie MV441 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 7-21-2020 Page 1 of 6
PRODUCT NAME: Stephanie Bookcase
ITEM NUMBER: MV441
ASSEMBLED DIMENSIONS : 84”H x 61”W x 20”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN INDONESIA

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 6
Ltr.
A8
B 2
Qty. Hardware Included
Ltr.
E
F
2
1
Qty. Components
C
2
REQUIRED TOOLS:
Phillips Screwdriver, Pencil,
Drill with 5/16” Bit
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
2
2
Wall Screws
(Anti-tip)
Top Screws
(Anti-tip)
Wall Anchoring
(Anti-tip) L-Brackets
See page 4
Expansion Bolts
Shelf Supports
H
I
Shelves (H)
Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
Lock Washers
G2
D2
Flat Washers
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
Bookcase (I)
Assemble in location for intended use.

Page 3 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Determine placement for each Shelf (H) then insert Shelf Supports (A) into corresponding
pre-drilled holes.
(A)
(H)
STEP 2: Bookcase is equipped with Rotary Levelers installed under each corner. Move Bookcase (I) to
final installation location, push against wall and check for level. If necessary, Bookcase may be adjusted
by carefully lifting applicable corner and turner Leveler clockwise/counterclockwise.
IMPORTANT: Level Bookcase BEFORE anchoring to wall.
Assemble in location for intended use.

Page 4 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEPS 3 through 5 cover anchoring unit to wall which MUST be completed before use.
STEP 3: Determine installation location, then identify two *wall studs behind bookcase. Push bookcase
into place then slide each L-Bracket (F) over top of Bookcase and center in front of each *wall stud. Use
pencil to mark wall at top of each Bracket.
IMPORTANT: Orient Brackets as illustrated to ensure they are not visible after installation.
Wall Studs
(F)
Pencil mark here
STEP 4: Pull Bookcase (I) away from wall, align L-Brackets (F) with marks on wall then anchor
L-Bracket directly into wall stud using Wall Screw (B) with Lock Washer (D) and Flat Washer (E).
Open Drywall
Wall Stud
*Optimal protection against a dangerous tip-over accident is provided when L-Brackets are directly
anchored into a Wall Stud. If this is not possible, use an Expansion Bolt (G) (See Page 6) which
provides optimal support when no Wall Stud is present (Open Drywall).
(B)
(D)(E)
(F)
Tip-Over Hazard

Page 5 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 5: Move Bookcase (I) back into place and slide under both L-Brackets (F) and attach using Top
Screws (C). Use a Phillips Screwdriver to firmly tighten.
(C)
(I)
(I)
(F)
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alchohol based
cleaners or polishers. Promply remove spills.

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 6 of 6
Drywall
5/16” Drill Bit
(G)
Teeth
Barrel
(D)
(F)
(E)
STEP 1: For Bracket (F) location in open Drywall, first use a 5/16” bit and drill a small pilot hole.
Next, use a Hammer to GENTLY tap in Expansion Bolt (G) until teeth sink evenly into wall surface.
STEP 2: Turn Screw clockwise until it begins to slip, indicating the Barrel has fully crimped and
secured against inside of wall. Finally, turn Screw counterclockwise and completely remove.
Add Lock Washer (D), Flat Washer (E) to Screw then insert through Bracket (F) as illustrated.
Reinsert Screw into Barrel and fully tighten to secure Bracket to wall.
HOW TO INSTALL AN EXPANSION BOLT