Ballard Designs Camile MO586 User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 10-27-2020 Page 1 of 5
PRODUCT NAME: Camile Desk
ITEM NUMBER: MO586
ASSEMBLED DIMENSIONS : 30”H x 52”W x 21”D
MADE IN INDONESIA
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 5
Ltr.
A8
B8
Qty. Hardware Included
Ltr.
F
G
1
2
Qty. Components
C8
REQUIRED TOOLS:
Phillips Screwdriver,
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Top (F)
Leg Assemby (G)
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
Allen Bolts
6 x 40mm
Lock Washers
6mm
Flat Washers
16 x 6 x 2mm
D1Allen Wrench
E2
Wall Anchoring
Anti-tip Kits
(See Page 5)
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alchohol based
cleaners or polishers. Promply remove spills.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Assemble in location for intended use.

Page 3 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Remove SIDE DRAWERS by first fully opening and locating RELEASE LEVERS on metal
glides. Press DOWN on RIGHT LEVER and pull UP on LEFT LEVER while gently pulling Drawer out.
STEP 2: Invert Top (F) onto a level, padded surface and orient each Leg Assembly (G) as illustrated.
Secure Assemblies to Top using Allen Bolt (A) with Lock Washer (B) and Flat Washer (C). Insert and
thread in all Bolts into embedded T-nuts before using Allen Wrench (D) to fully tighten and secure.
(C)
(B)
(A)
(D)
(F)
(G) (G)

Page 4 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: Turn Desk upright onto Legs then reinstall both Drawers by aligning metal glides and gently
pushing drawer closed. NOTE: Drawer may need to be open/closed several times for glides to lock
in place.
LEVELERS: Desk is equipped with Rotary Levelers installed under each Leg. If necessary, Desk may
be adjusted by carefully lifting applicable corner and turning Leveler clockwise/counterclockwise.

Page 5 of 5
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(C)
(B)
(D)
(A)
(6 x 1
12
'')
(6 x
34
'')
5. Confirm Belt is securely laced and locked.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
with Large Screws (B) 2 inches below Bracket attached to back of unit.
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screws (A).
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2
D
Bracket4
C
Large Screw
4B
Hardware Included
Qty.
Retention Belt
Small Screw
4
A
Ltr.
WALL ANCHORING HARDWARE (ANTI-TIP)
WALLBRACKET MUST BE ATTACHED TO WALL STUD
WALL STUD
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING