Ballard Designs Biaggi Bar Cabinet User manual

Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 6-1-2021 Page 1 of 4
PRODUCT NAME: Biaggi Bar Cabinet
ITEM NUMBER: SR021
ASSEMBLED DIMENSIONS : 59 1/4”H x 42”W x 22”D
MADE IN ITALY
Customer Service: 800-367-2810
Online: www.ballarddesigns.com

Page 2 of 4
Ltr.
F
G
1
1
Qty. Components
REQUIRED TOOLS:
Phillips Screwdriver
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
ANCHORING HARDWARE INCLUDED
H
Cleaning and Care
Periodically dust with a soft, dry cloth.
Prevent finish damage: do not use alchohol based
cleaners or polishers. Promptly remove spills.
1
Cabinet (F)
Lower Shelf (G)
Compartment Shelf (H)
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Ltr.
C
B
4
4
Qty. Hardware Included
A
4
D1
E
Screws
Connector Pegs
Shelf Supports
Door Key
Wall Anchoring
Anti-tip Kits
See Page 4
2
Assemble in location for intended use.

Page 3 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Lower Shelf (G) is installed one side (left/right) at a time. 1. Carefully place Cabinet (F) back
down onto a level, padded surface. 2. Insert and tighten a Connector Peg (B) into hole in lower portion
of each LEFT leg . NOTE: Orient side hole in Connector Peg facing up, toward Cabinet. 3. Fit one end
of Lower Shelf over Connector Pegs and fit Shelf between all four legs.
4. Insert and tighten remaining Connector Pegs into both RIGHT legs. 5. Secure Shelf with Screws (A).
13
24
Set Cabinet back side down. Insert Connector Pegs
into both LEFT legs.
Fit Lower Shelf
into place.
Insert Connector Pegs
into both RIGHT legs.
5
(B)
(F)
(G)
(A)
Secure Lower Shelf by inserting and gently tightening
Screw (A) through hole in each Connector Peg and
into Shelf.
Carefully set Bar Cabinet upright.
STEP 2: Determine location for Compartment
Shelf (H) then insert Shelf Supports (C) into
corresponding pre-drilled holes.
Carefully set Shelf level upon supports.
(H)
(C)
Assemble in location for intended use.

Page 4 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Installation:
Ltr.
A2
Small Screw
Retention Belt
Qty. Hardware Included
B2
Large Screw
C4 Bracket
D2
WALL ANCHORING HARDWARE (ANTI-TIP)
1. Place furniture against wall at desired location then locate and mark a Wall Stud behind unit.
2. Corresponding to Stud location, attach one Bracket (C) to back of unit using Small Screw (B).
3. To keep hardware out of view after installation, attach remaining Bracket (C) INTO WALL STUD
with Large Screw (A) 2 inches below Bracket attached to back of unit.
4. Move unit into place, align Brackets then connect both using Retention Belt (D).
5. Confirm Belt is securely laced and locked.
Serious or fatal crushing injuries can occur from a furniture tip-over
Tip-Over Hazard
Prevent tipping accidents. Anchor your furniture.
WARNING
W
A
L
L
S
TUD
WALL BRACKET MUST BE ATTACHED TO WALL STUD
(A)
(B)
(C)
(D)
R
e
presen
t
a
tiv
e
Fu
r
nitu
r
e
I
tem