Ballard Designs Tuscan MO362 User manual

PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
UPDATED: 6-13-2019 Page 1 of 6
PRODUCT NAME: Tuscan Double Pedestal Desk (Top, Base Cabinets)
ITEM NUMBER: MO362 (Includes MO361 & MO251)
ASSEMBLED DIMENSIONS : 30”H x 72”W x 36”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
IMPORTED

Customer Service: 800-367-2810
Online: www.ballarddesigns.com
1 each -MO361: Desk Top (F)
2 each - MO251: Base Cabinet (H) and Shelf (G).
Shelf and Shelf Supports
located on underside of
each Base Cabinet.
Return Desk comprised of two parts, MO361 Desk Top and two MO251 Base Cabinets.
Illustration below shows location of parts and hardware.
NOTE
Carefully remove all outer packaging of both MO361 and MO251 and place components on a
soft, level surface.
Hardware Packet
(H)
(G)
Page 2 of 6

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 3 of 6
Ltr.
A 8
B 8
Qty. Hardware Included
Ltr.
F
H
1
2
Qty. Components
C 8
TOOLS NEEDED:
Allen Wrench (included)
-Two person assembly suggested.
Remove all parts, hardware and
protective packaging from carton
and carefully arrange on a clean,
level, padded surface.
NOTE: To avoid accidentally
discarding small parts or hardware,
retain all carton contents until
assembly and installation are complete.
G 2
D
E 1
8
Allen Bolt
Lock Washer
Flat Washer
Shelf Support
Allen Wrench
Desk Top
Shelf
Base Cabinet

(F)
(H)
(H)
Push Black Lever in side rails up on one side
and down on the other while pulling drawer out
TO REMOVE DRAWERS
Page 4 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1: Arrange Base Cabinets (H) and remove top drawer from each by extending
drawer, pulling up on black lever on one rail while pushing down on the other and sliding
drawer out. Lay to the side. Next, orient and lay Desk Top (F) onto Base Cabinets.
NOTE: Base Cabinets may be oriented in either direction.
Align Desk Top (F) with holes in Base Cabinets (H) and attach together using Allen
Bolt (A), Lock Washer (B), and Flat Washer (C). Firmly tighten and secure tighten each
bolt using Allen Wrench (E).
STEP 2:
(F)
(E)
(C)
(B)
(A)
(H)

Page 5 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 3: Insert Shelf Supports (D) in desired loctation and gently place shelves upon supports.
If necessary, desk may be leveled by adjusting Rotary Levelers located on the bottom corner
of each Base Cabinet. Turn Leveler clockwise/counterclockwise until desk is level.
STEP 4:
Cleaning & Care:
DO NOT use alcohol based products or spray polisher as finish damage may result.
Dust with a soft cloth.
(G)
(G)
(G)
(D)

Page 6 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Anti Tip Installation Part C: Where applicable, attach desk to wall.
Attach 2 Brackets (C) through the smaller holes to Desk with Small Screws (A)
Attach remaining Brackets (C) INTO A WALL STUD with Large Screws (B) 2 inches below
the Brackets attached to Desk. Align the Brackets vertically and
string in the Retention Belts (D). Confirm Straps are securely laced and locked.
Ltr.
A
(B)
(A)
(C)
(C)
(D)
2 Small Screw
Retention Belt
Qty. Hardware Included
B2 Large Screw
C4 Bracket
D2
WALL
STUD
WARNING
Tip-Over Hazard
WALL BRACKET MUST BE ATTACHED TO WALL STUD
Prevent tipping accidents. Anchor your furniture.