BLK BOX FULL-HALF COMBO RACK GOLIATH User manual

OWNERS MANUAL & QUICK START GUIDE
FULL - HALF COMBO RACK GOLIATH
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
21-0114-0B
#MADEINBELFAST
220kg
PRODUCT SPECIFICATION
PRODUCT WEIGHT
MAX USER WEIGHT
MAX USER
MAX TRAINING WEIGHT
DIMENSIONS
SAFE WORKING ZONE
-125kg
300kg
1200mm x 2120mm x 2408mm
-
-
-
-2700mm x 4520mm x 3272mm
3
-

WARNING
SPIRIT LEVEL
10MM MASONRY
DRILL BIT
TOOLS REQUIRED
17MM SPANNER X2
13MM SPANNER
HAMMER
HAMMER DRILL VACUUM STEP LADDER
PARTS & ATTACHMENTS
No. Name SKU QTY
1 2.4 UPRIGHT DNA60
WITH FEET
21-0036-0A 8
2 1.2 BRANDING BOX CM
DNA60
21-0017-0A 1
3 1.2 SINGLE BAR CM
DNA60
21-0015-0A 1
4 1.2 BOX CM DNA60 21-0013-0A 6
5 MULTIGRIPS DNA60 21-0151-0A 2
6 0.4 BOX CM DNA60 21-0036-0A 8
7 J-HOOKS PAIR 16-0001 2
8 M10X80 SLEEVE
ANCHOR
10-0031 24
9 M10X90 BOLT 10-0008 62
10 M10 FLAT WASHER 10-0019 148
11 M10 NYLOCK NUT 10-0024 62
1
2
3
4
6
7
8
9
11
10
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS ENSURE
BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER REDUCE RISK OF
INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PROTECTIVE EQUIPMENT (PPE).
WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN THE ASSEMBLY OF THIS PRODUCT.
EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES, STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS LEVEL
OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL.
#MADEINBELFAST
5
xx
Nm

ASSEMBLY
x
8
x
4
1
BOLT 1QTY BRANDING BOX (21-0017-0A] AND 1QTY 1.2 BOX (21-0013-0A) BETWEEN 2QTY
UPRIGHTS (21-0036-0A) WITH BOLTS ASSEMBLY AS SHOWN. ENSURE LOGO ON
BRANDING BOX (21-0017-0A) IS FACING FORWARD, LOGOS ON UPRIGHTS ARE
FACING OUT AND ALL BOLTS FACING INWARDS.
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
#MADEINBELFAST

M10x90 Bolt, Washer
x2 & Nylock Nut
x
4
x
4
x
4
x
8
2
BOLT 1QTY 1.2 SINGLE BAR (21-0015-0A) BETWEEN 2QTY UPRIGHTS (21-0036-0A) AND CONNECT TO
EXISTING ASSEMBLY USING 4QTY BOX (21-0036-0A) WITH BOLT ASSEMBLY AS SHOWN. ENSURE
LOGO ON UPRIGHTS ARE FACING OUT AND BOLTS ARE FACING INWARD.
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
#MADEINBELFAST

M10x90 Bolt, Washer
x2 & Nylock Nut
x
4
x
4
x
4
x
8
x
6
3
BOLT 1QTY 1.2 BOX (21-0013-0A) BETWEEN 2QTY UPRIGHTS (21-0036-0A) AND CONNECT
TO EXISTING ASSEMBLY USING 4QTY BOX 1.2 BOX (21-0013-0A) BOLT 1QTY MULTIGRIPS
(21-0151-0A) TO 1QTY 1.2 BOX (21-0013-0A) WITH BOLT ASSEMBLY AS SHOWN, ENSURE
LOGO ON UPRIGHTS ARE FACING OUT AND BOLTS ARE FACING INWARD.
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
#MADEINBELFAST

4
BOLT 1QTY 1.2 BOX (21-0017-0A) BETWEEN 2QTY UPRIGHTS (21-0036-0A) AND CONNECT TO
EXISTING ASSEMBLY USING 4QTY BOX 0.4 BOX (21-0036-0A) BOLT 1QTY MULTIGRIPS (21-0151-0A)
TO 1QTY 1.2 BOX (21-0013-0A) WITH BOLT ASSEMBLY AS SHOWN, ENSURE LOGO ON UPRIGHTS ARE
FACING OUT AND BOLTS ARE FACING INWARD.
#MADEINBELFAST
x
4
x
4
x
8
x
6
x
4
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024 10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024 10.0008
10.0019 x2
10.0024

30
Nm
DRILL HOLE VACUUM HAMMER IN
BOLT TIGHTEN
90MM
SLEEVE ANCHOR BOLT FITTING
-DRILL 10MM HOLE THROUGH FLOOR COVERING,
90MM DEEP USING PLATE AS A GUIDE.
-VACUUM OUT THE DUST.
-HAMMER SLEEVE ANCHOR DOWN INTO THE HOLE.
-TIGHTEN SLEEVE ANCHOR TO SPECIFIED TORQUE
USING 13MM SPANNER.
5
#MADEINBELFAST
x
8
x
8
30
Nm
x48
10.0031
10.0019
10.0031
10.0019
TIGHTEN ALL BOLT ASSEMBLIES WITHIN THE CIRCLE TO SPECIFIED TORQUE. ENSURE ALL
UPRIGHTS ARE PLUMB. DRILL AND SECURE THE MIDDLE HOLE ON EACH UPRIGHT AS SHOWN
IN GUIDE. REMOVE ALL BOTTOM CROSSMEMBERS, DRILL AND SECURE REMAINING HOLES ON
UPRIGHTS AS SHOWN IN GUIDE. REATTACH THE BOTTOM CROSSMEMBERS .

1:1 SCALE FASTENERS
FOR TERMS AND CONDITIONS VISIT OUR WEBSITE AT
www.blkboxfitness.com/pages/terms-conditions
GET IN TOUCH
TEL: [phone]
EMAIL: [e-mail]
DISCOVER MORE AT:
www.blkboxfitness.com
M10x80 SLEEVE ANCHOR
10-0031
M10x90 BOLT
10-0008
NYLOCK NUT
10-0024
M10 FLAT WASHER
10-0019
#MADEINBELFAST