BLK BOX GOLIATH QUARTER RACK User manual

OWNERS MANUAL & QUICK START GUIDE
GOLIATH QUARTER RACK
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
21-0113-0D
#MADEINBELFAST
1112mm x 1320mm x 2266mm
2312mm x 2820mm x 3076mm
55kg
PRODUCT SPECIFICATION
PRODUCT WEIGHT
MAX USER WEIGHT
MAX USER
MAX TRAINING WEIGHT
DIMENSIONS
SAFE WORKING ZONE
-125kg
350kg
-
-
-
-
1
-

WARNING
10MM MASONRY
DRILL BIT
TOOLS REQUIRED
2x 17MM SPANNER
HAMMER DRILL VACUUM
#MADEINBELFAST
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS ENSURE
BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER REDUCE RISK OF
INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PROTECTIVE EQUIPMENT (PPE).
WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN THE ASSEMBLY OF THIS PRODUCT.
EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES, STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS LEVEL
OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL. xx
Nm

PARTS & ATTACHMENTS
#MADEINBELFAST
1
2
3
4
5
7
8
9
10
11
6

ASSEMBLY
1
ARRANGE 2QTY OF QUARTER RACK BASE FRAME (21-0572-0A) ON THE GROUND. ENSURE
THEY ARE ORIENTATED SO THAT 2 SLOTS ARE VISIBLE ON TOP, AS SHOWN BELOW. NOT
4 SLOTS.
#MADEINBELFAST

#MADEINBELFAST
2
ASSEMBLE THE 2QTY BASE FRAMES (21-0572-0A) WITH THE BACK CM (21-0602-0A).
FASTEN TOGETHER USING 2QTY M10X90 HEX HEAD BOLT (10-0008), 4QTY M10 WASHER
(10-0019) AND 2QTY M10 NYLOC NUT (10-0024) PER SIDE.
10-0008 x 2
10-0019 x 2
10-0019 x 2
10-0024 x 2
30
Nm

#MADEINBELFAST

#MADEINBELFAST
3
ASSEMBLE 2QTY QUARTER RACK UPRIGHT (21-0573-0A). ENSURE THE TABS ON THE UP-
RIGHTS ALIGN WITH THE SLOTS ON THE BASE FRAMES (21-0572-0A). ALSO ENSURE THAT
THE BLK BOX LOGO IS FACING OUTWARD FROM THE RACK.
FASTEN TOGETHER USING 4QTY GOLIATH BRACE PLATE (20-0472-0A), 8QTY M10X90 HEX
HEAD BOLT (10-0008), 16QTY M10 WASHER (10-0019), AND 8QTY M10 NYLOC NUT (10-0024).

#MADEINBELFAST
10-0008 x 4
10-0019 x 4
10-0019 x 4
10-0024 x 4 30
Nm

#MADEINBELFAST

4
FASTEN 1QTY TO 1.2 SINGLE BAR (21-0015-0A) TO THE 2QTY UPRIGHTS USING 4QTY
M10X90 HEX HEAD BOLT, 8QTY M10 WASHER, AND 4QTY M10 NYLOC NUT.
#MADEINBELFAST
10-0008 x 2
10-0019 x 2
10-0019 x 2
10-0024 x 2
30
Nm