Bosch SCT 815 User manual

SCT 815
Uncrating & Assembly

Uncrating and Assembling the SCT 815
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

Tools required to assemble SCT 815.
Uncrating & Assembling SCT 815
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

1. Open box and remove all packing material
and contents.
2. Dispose of packing materials and boxes
properly.
Uncrating & Assembling SCT 815
1
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

2. Open boxes and check received contents
with packing list.
Uncrating & Assembling SCT 815
2
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

3. Unpack Operating Instructions 1 689 989 362.
Uncrating & Assembling SCT 815
3
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

4. Remove Operating Instructions and
contents.
Uncrating & Assembling SCT 815
4
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

5. Open box & remove Base Plate from
1 688 000 368.
Uncrating & Assembling SCT 815
5
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

6. Place Base Plate on surface with leveling
screw knobs pointing up.
Uncrating & Assembling SCT 815
6
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

7. Locate hex screws, nuts & washers:
Hex Screws, nuts & washers 1 687 010 613
Plastic Screws 1 683 414 021
Uncrating & Assembling SCT 815
7
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

8. Unpack & sort hex screws, nuts & washers.
Uncrating & Assembling SCT 815
8
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

9. Cut tie wraps from Guide Tubes 1 680 700
313.
Uncrating & Assembling SCT 815
9
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

10. Separate the 2 Guide Tubes.
Uncrating & Assembling SCT 815
10
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

11. Place Guide Tube on to Base Plate, locate
Hex Screws & Washers.
Uncrating & Assembling SCT 815
11
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

12. Place washers over hex cap screw.
Uncrating & Assembling SCT 815
12
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

13. Install hex cap screws & tighten to 6nm.
Uncrating & Assembling SCT 815
13
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

14. Repeat the process of installing the second
Guide Tube on the Base Plate.
Uncrating & Assembling SCT 815
14
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

15. Unpack Tool Holder 1 688 040 319.
16. Tool Holder 1 688 040 319.
Uncrating & Assembling SCT 815
15
16
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

17. Remove Knurled Screw & separate Tool
Holder halves.
Uncrating & Assembling SCT 815
17
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.

18. Install Tool Holder bottom half on back side
of Guide Tubes; the threaded plastic bolt of
the Tool Holder points up to the Base Plate
triangle.
Uncrating & Assembling SCT 815
18
© Robert Bosch GmbH 2016. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the event of applications for industrial property rights.