Bradley Express SS Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
SS-3N Infrared
(Standard and Wall-Hung)
Express®Lavatory System SS-Series
Table of Contents
Pre-Installation Information................................................2
Components ......................................................................3
Supplies Required .............................................................4
Dimensions....................................................................4–5
Rough-Ins ..........................................................................6
Mount Frame to Wall .........................................................7
Install Bowl ........................................................................7
Connect the Supply ...........................................................8
Install Drains......................................................................9
Connect Electrical and Sprayhead Supplies .....................9
Adjust Temperature..........................................................10
Sensor Assembly and Solenoid Valve Access ................10
Solenoid Valve Troubleshooting.......................................11
Navigator® Mixing Valve Troubleshooting .......................12
Stop Valve Troubleshooting .............................................13
Cleaning and Maintenance for Terreon®.........................13
Soap Dispenser Maintenance .........................................14
Express Lavatory Systems are ADA and TAS compliant
U.S. Pat. Nos. 5,611,093, 5,369,818, D398,969
Other Patents Pending
215-1493 Rev. K; ECN 17-08-010
© 2017 Bradley
Page 1 of 14 5/18/2017
SS-3N with infrared activation, standard
frame and liquid soap dispenser
SS-3N with infrared activation, wall-hung
frame and liquid soap dispenser

SS-3N Installation
25/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010
Special Note for Sprayhead/Bowl retrofit
to retrofit new SS-3N sprayhead onto existing SS-3 bowl
1½" (38mm)
Drill hole Ø 1" (25mm)
to 1½" (38mm).
Existing Hole
2¼" (57mm)
WARNING
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation. Electrical
power MUST remain off until installation is complete. After installation is complete, turn on the water supply
first, then turn on the electrical power.
Hardware supplied by installer must be appropriate for wall construction. Wall anchors must have a
minimum pull-out rating of 1,000 lbs. Follow appropriate dimensions for standard or juvenile height based on
configuration and required rim height. Overtightening fasteners can damage the Terreon® material. Use caution
when tightening bowl and sprayhead fasteners.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file this
manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances
is the responsibility of the installer. Product warranties may be found under "Products" on our Web site at
www.bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.

Installation SS-3N
Bradley • 215-1493 Rev. K; ECN 17-08-010 5/18/2017 3
Components
Power Adapter
(261-147A)
Sprayhead Cover
(SS-3N-COVR-ONLY)
Contact your local Bradley Rep for part number.
Sprayhead Body
(SS-3N-SPYD-ASSY)
Contact your local Bradley
Rep for part number.
Bowl
(SS-3N-BOWL)
Contact your local Bradley
Rep for part number.
Washer
(142-002BJ)
LockWasher
(142-002BK)
Nut, 5/16-18
(161-036)
Main Frame
(S17-323)
Pedestal Panel, Coal
(186-1454B)
Panel Fasteners (160-450)
Washers (142-002CA)
(8) Places
Screw, 10-24
(160-386)
Bolt, 5/16-18
(160-371)
Polypropylene P-Trap
(269-1697)
Optional Chrome Plated Brass
P-Trap (S29-094)
Waste Tee
(111-063)
Waste Shoe
(111-062)
1/8" Rubber Washer
(125-001DP)
Drain Plug
(P16-072)
Strainer
(P16-075)
#8-32 Screw
(160-319)
Drain Assembly
Bowl Mounting
Hardware
1/4"-20 x 1/2" Pan
Head Screw (Qty 4)
(160-389)
1/4"-20 Washer
(Qty 4)
(142-002DB)
Scuff Base Panel,
Coal (185-033B)
Scuff Panel Fasteners
(160-450)
Washers (142-002CA)
(4) Places)
Scuff Base (17-324)
(used with standard
height frame only)

SS-3N Installation
45/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010
Supplies Required
• (8) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall (minimum pull-out rating
of 1,000 lbs.)
• STD. HEIGHT ONLY: (2) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount scuff base to wall
• 1/2" nominal copper tubing for hot and cold supplies and 1-1/2" NPT drain piping
• 120V/220V 50/60 Hz power source using Bradley supplied 120VAC/12V DC plug in adapter
Dimensions - Front and Top Views
SOAP
SOAP SOAP
SOAP
Top View 80"
(2032)
Front View
Standard Frame
Front View
Wall-Hung Frame
8-5/8" (219)
30"
(762)
8"
(203)
51-1/4" (1302)
58" (1473)
64" (1626)
68-1/4" (1734)
8" (203)
68-1/4"
(1734)
58" (1473)
64" (1626)
8" (203) Radius 10" (254) Radius
30"
(762)
(mm)

Installation SS-3N
Bradley • 215-1493 Rev. K; ECN 17-08-010 5/18/2017 5
Dimensions - Side Views
TAS
TAS
Wall Hung Mounted
at Standard Height
Standard
Height
Wall Hung Mounted
at Juvenile Height
Ages: 6 through 12
Wall Hung Mounted
at TAS Height
Grades: 6
through
8 or 9
Wall Hung Mounted
at TAS Height
Grades: Pre-K
through 5 or 6
21-1/8"
(537)
38-1/2"
(978)
34"
(864)
30"
(762)
13-1/4"
(311)
11-1/2"
(292)
Scuff Base on
Standard Height Only
3" (76)
8-5/8"
(219)
21-1/8" (537)
11-1/2"
(292)
(mm)
38-1/2"
(978)
34"
(864)
30"
(762)
13-1/4"
(311)
8-5/8"
(219)
21-1/8"
(537)
11-1/2"
(292)
8-5/8"
(219)
35-1/2"
(902)
31"
(787)
27"
(686)
10-1/4"
(260)
21-1/8"
(537)
11-1/2"
(292)
8-5/8"
(219)
36-1/2"
(927)
32"
(813)
28"
(711)
11-1/4"
(286)
21-1/8"
(537)
11-1/2"
(292)
8-5/8"
(219)
34-1/2"
(876) 30"
(762)
26"
(660)
9-1/4"
(235)

SS-3N Installation
65/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010
CODE DESCRIPTION QTY.
A 3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs. for Bowl 2
B 3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs. for Mainframe 6
C3/8" Wall Anchors for Base Frame, Standard Frame option only, minimum pull-out force not
required 2
D1 1/2" nominal copper tubing for Cold Supply, stub-out 2" from wall 1
D2 1/2" nominal copper tubing for Hot or Tempered Supply, stub-out 2" from wall 1
E 1-1/2" NPT Drain, stub-out 2" from wall 2
F
On the bowl back, measure the distance between the 3/4" bowl mounting holes. Divide this
measurement in half. Measure and mark this dimension on the wall to the left and the right
of the centerline. Install two 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs
(supplied by installer) at locations marked.
2
J 110v GFI Protected Electrical Outlet 1
RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FOR
CODES A–E, H, C and W FIXTURE STYLE
34" None Standard Height
34" None Wall-Hung
32" Subtract 2" TAS, Grades 6 through 8 or 9
31" Subtract 3" Juvenile Height
30" Subtract 4" TAS, Pre-K through Grades 5 or 6
Rough-Ins
1
38-1/2"
(978)
38-1/2"
(978)
24-3/8"
(619)
24-3/8"
(619)
13"
(330)
8"
(203)
4"
(102)
2-3/4"
(70)
32"
(813)
28-3/4"
(720)
15"
(381)
3-1/2"
(89)
24"
(610) 5-5/8"
(143)
Floor
A, F
B
B
C
D1 D2 E
B
B
J
B
B
C
A, F
34"
(864)
Rim
Height
See
Chart
Below

Installation SS-3N
Bradley • 215-1493 Rev. K; ECN 17-08-010 5/18/2017 7
Anchoring the frame to a wall that is not flat may
cause the frame to bend, making it difficult to
reinstall the access panels. If necessary, use
shims to compensate for wall distortion.
The sprayhead body has slotted holes for adjusting the fit-up with the
bowl and wall.
For clarity, the scuff base frame and drain are not shown. Turn the
tailpiece down to its proper position before installing the bowl.
Mount Frame to Wall
2
Using a T20 torx key, remove the
fasteners securing the access
panel to the main frame, and
remove the panel.
A
Once the frame is level and flat against
the wall or shimmed, mount the frame
to the wall at six places using 3/8"
bolts and 1" min. O.D. washers.
B
When mounting the standard height frame,
mount the scuff base to the wall at the same
time using two additional 3/8" bolts and washers.
Install Bowl
3
Attach the bowl to the frame with
1/4"-20 x 1/2" pan-head screws
and washers. Do not tighten.
A
Tighten the pan-head screws.
DO NOT OVERTIGHTEN.
C
Secure the bowl to
the wall anchors
with 3/8" bolts
and 1" min. O.D.
washers, two
places. Do not
overtighten.
B

SS-3N Installation
85/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010
45
45
The letter “H” on the Navigator Mixing
Valve indicates hot water supply inlet.
Connect the Supply - Hot and Cold Supply
4
Loosen but do not remove the two
mounting screws holding the valve
bracket to the frame.
Slide the valve bracket up and lift it
from the frame.
A
Connect one end of each hose to
the Navigator valve (one on the hot
side, one on the cold side).
Connect the other swivel end to the
stop valves.
C
Attach the stops to the hot and
cold water wall stub-outs.
B
Connect the Supply - Single Tempered Supply
4b
Loosen but do not remove the two
mounting screws holding the valve
bracket to the frame.
Slide the valve bracket up and lift it
from the frame.
A
Connect one end of flexible hose
to the tempered line adapter.
Connect the other swivel end to
the stop valve.
C
Attach the stop to the tempered
wall stub-out.
B

Installation SS-3N
Bradley • 215-1493 Rev. K; ECN 17-08-010 5/18/2017 9
Install the Drains
5
To Drain
Stub-Out
Connect Electrical and Sprayhead Supplies
6
WARNING The Express activation must be connected with the 120VAC/12V DC plug-in adapter provided.
Not using the provided adapter can cause personal injury and will result in damage to the
electronics.
Snap each sensor circuit plug into the
associated solenoid circuit plug located on
the valve bracket.
A
Snap the wall adapter barrel plug into the
barrel plug located on the valve bracket
wire harness.
B
Supply Inlet
Compression
Nut
(110-231)
Black Supply Tube
(From Sprayhead)
Green Supply Tube
(From Sprayhead)
Red Supply
Tube (From
Sprayhead)
Navigator Thermostatic
Mixing Valve
Loosen the compression nuts.
Push the sprayhead supply tubes firmly into the
tube connectors until they are fully seated.
Tighten the compression nuts by hand.
C

SS-3N Installation
10 5/18/2017 Bradley • 215-1493 Rev. K; ECN 17-08-010
Sprayhead
Components Infrared Sensor
269-1608HP-DC
Sensor Assembly and Solenoid Valve Access
To access sensors:
1. Remove the Phillips-head screws located in the bottom of the sprayhead body.
2. Lift the Terreon cover/shelf off.
To reinstall sprayhead cover/shelf:
1. Position the cover/shelf on the sprayhead body.
2. Secure it to the sprayhead body using the screws provided.
Window
(269-1241)
O-Ring
(125-157)
Aerator Assembly
(S05-180)
Nut, ½"-14 NSPM
(110-115)
Adjust the Temperature
7
H
C
ALoosen Cap Screw about 1/4" (4-6
turns) and lift up cover (do not
remove).
BUsing cover, turn cartridge gently until
desired water temperature is reached.
Do not turn past stops as this may
damage unit. Push cover down and
tighten screw.
WARNING This valve is NOT factory
preset. Upon installation,
the temperature of this
valve must be checked and
adjusted to ensure delivery
of a safe water temperature.
Water in excess of 110°F
(43°C) may cause scalding.
C
Reinstall the valve bracket. Turn on the water supply and check for leaks. Turn on the
electrical power to the electrical outlet and pass your hand in front of each station’s
sensor until all the air is purged from the lines and water is flowing smoothly. Reinstall the
access panel.
Wait two full minutes after making the power connection before using the lav. The
sensors will take up to eight full minutes (while not in use) to adapt to the bowl if
another object is detected during the two-minute start-up period.