Bradley Verge LVRD Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1669 Rev. K; ECN 18-08-010A
© 2018 Bradley
Page 1 of 12 7/25/2018
LVRD2
Verge®Lavatory System – LVRD-Series
with Evero®Natural Quartz Material
Table of Contents
Components................................2–3
Supplies Required .............................4
Dimensions ................................4–5
Rough-Ins ...................................6
Frame Mounting...............................7
Faucet Box Mounting ...........................7
Drain Assembly ...............................8
Faucets and Optional Soap Valve .................8
Bowl Mounting ................................9
Strainer and P-trap............................10
Adjust the Temperature ........................10
Trap Cover ..................................11
Cleaning and Maintenance .....................12
WARNING
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation.
Electrical power MUST remain off until installation is complete.
Installer’s hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out
rating of 1,000 lbs.
NOTICE
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file
this manual with the owner or maintenance department. Compliance and conformity to local codes and
ordinances is the responsibility of the installer. Product warranties may be found under “Products” on our
Web site at bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
For standard height mounting, do not exceed the recommended 34" distance from the top of the lav deck
to the finished floor. To meet ADA requirements, the lav deck cannot exceed the 34" maximum height
dimension.

LVRD2 Installation
27/25/2018 Bradley • 215-1669 Rev. K; ECN 18-08-010A
Components
Chrome P-trap (S29-094)
Plastic P-trap (269-1697)
Frame
(S17-362)
Access Panel
(186-1813)
Hose Prepack
(S45-2730)
Hose Prepack
(S45-2731)
TMV Supply
Connections
Tempered Supply
Connections
Complete Hardware Prepack (S45-2473)
Frame Mounting Qty.
Washer, Square 9 (4 extra)
Washer, Flat 1" O.D. 2
Bowl-To-Frame (S45-2481) Qty.
Screw, ¼-20 x ½" 3 (1 extra)
Washer, Flat ⁵⁄₈" O.D. 3 (1 extra)
Trap Cover (S45-2482) Qty.
Screw, 10-24 x ½" 6 (2 extra)
#10 Finishing Washer 6 (2 extra)
Trap Hook Bracket 1
Screw, 10-24 x 3⁄8" 1
Washer, Flat 35⁄64" O.D. 1
Bowl
Contact your Bradley Representative for color options
Complete Drain Prepack
(S45-2471)
Strainer and
Screw
(S45-2479)
O-Ring
(125-111)
Drain
Adapter
Packing
Washer
#10-24
Screw
Drain Adapter
Prepack
(S45-2480)
Water supply to battery box solenoid MUST be supplied
using a plastic hose (provided by Bradley).
Cold
TMV Valve
(½" NPTM Outlet)
(S45-2478)
Plastic
Hose Plastic
Hose
Stainless
Steel
Hose
Plastic
Hose
Plastic Hose
Stainless Steel
Hose
Supply Fittings
(S45-2510)
Supply Fittings
(S45-2511)

Installation LVRD2
Bradley • 215-1669 Rev. K; ECN 18-08-010A 7/25/2018 3
Components
IR-DCD Faucet*
(S53-336)
CAP-DCR Faucet
(S53-353)
Battery Box Prepack
(S45-2508)
(includes bracket and
mounting hardware)
Battery Box for
CAP-DCR Faucets
6315-KT0000 Soap Dispenser 6324-68 Soap Dispenser 6334 Soap Dispenser
Optional
Transformer
Plug-In Transformer
Option (PT) for
IR-DCD Faucet
(S53-337)
Plug-in transformer option (PT)
includes Transformer (S53-338),
Adapter (S53-339), and Grounding
Kit (S53-349) for CAP-DCR Faucets
IR-DCG Faucet*
(S53-350)
Plug-In Transformer
Option (PT) for
IR-DCG Faucet
(153-486)
*Adapter S45-2872 included with faucet *Adapter S45-2872 included with faucet

LVRD2 Installation
47/25/2018 Bradley • 215-1669 Rev. K; ECN 18-08-010A
15"
(381mm)
60"
(1524mm)
15"
(381mm)
36"
(914mm)
Dimensions
Top View
Front View
Supplies Required:
• (7)
3⁄8" lag screws, wall anchors, bolts (minimum pull-out rating of 1,000 lbs.)
• ½" hot/cold or tempered supply piping
• 1½" NPT drain piping
• OPTIONAL: 110 volt GFCI protected electrical outlet for 100–120 VAC plug-in transformer (for Bradley Faucets)
• Screen filter(s) as needed, if not included with faucet(s)
59"
(1499mm)

Installation LVRD2
Bradley • 215-1669 Rev. K; ECN 18-08-010A 7/25/2018 5
Dimensions – Side View
33½"
(851mm)
32½"
(826mm)
22½"
(572mm)
15¾"
(400mm)
157⁄16"
(392mm)
8½"
(216mm)
19¼"
(489mm)
30½"
(775mm)
29½"
(749mm)
22½"
(572mm)
15¾"
(400mm)
8½"
(216mm)
16¼"
(413mm)
28½"
(724mm)
29½"
(749mm)
22½"
(572mm)
15¾"
(400mm)
8½"
(216mm)
15¼"
(387mm)
30½"
(775mm)
22½"
(572mm)
15¾"
(400mm)
8½"
(216mm)
17¼"
(438mm)
31½"
(800mm)
Standard
Height
Juvenile
Height
TAS, Grades 6
through 8 or 9
TAS, Pre-K
through Grades
5 or 6 157⁄16"
(392mm)
157⁄16"
(392mm)
157⁄16"
(392mm)

LVRD2 Installation
67/25/2018 Bradley • 215-1669 Rev. K; ECN 18-08-010A
Rough-Ins
CODE DESCRIPTION QTY.
A
3⁄8
" Lav Deck Bowl Anchors with a Minimum Pull-Out Force of 1,000 lbs. (reinforce walls at anchor points) 2
B
3⁄8
" Lav Deck Frame Anchors with a Minimum Pull-Out Force of 1,000 lbs. (reinforce walls at anchor points) 5
H, C ½" Hot/Cold Supplies, Stub-Out 2" From Wall 1
D110v GFI Protected Electrical Outlet (AC version only)
Two single outlets are required for CAP-DCR faucets due to the size of the transformers. 2
E1½" NPT Drain, Stub-Out 2" from Wall 1
RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FOR CODES A–E and H FIXTURE STYLE
33½" None Standard Height
31½" Subtract 2" TAS, Grades 6 through 8 or 9
29½" Subtract 4" TAS, Pre-K through Grades 5 or 6
30½" Subtract 3" Juvenile Height
C
1" (25mm)
12"
(305mm)
33½"
(851mm)
Ref.
B
A
D
28"
(711mm)
E
31½"
(791mm) 24¾"
(629mm)
277⁄8"
(708mm)
H
277⁄8"
(708mm)
12"
(305mm)
3"
(76mm)
4" (102mm)
27¾"
(705mm)
GFCI Box
221⁄8"
(562mm)
197⁄8"
(505mm)
A
B
B B
311⁄8"
(791mm)
B
29½" (749mm) Ref. Dim.
to outside corner of bowl
(mark corner of bowl)
Reinforce wall at points A and B.
Standard rough-in shown.
30" (762mm) Ref. Dim.
to outside bottom corner of bowl
D
3½"
(89mm)

Installation LVRD2
Bradley • 215-1669 Rev. K; ECN 18-08-010A 7/25/2018 7
1Frame Mounting
2Faucet Box Mounting
Typical installation is shown. It may be necessary to repair the wall
after mounting. The fixture may not cover all of the wall modifications.
16"
(406mm)
centers
13"
(330mm)
A
Floor
Drywall
Drain, supplies and electrical box are
shown in their approximate locations.
Cut clearance holes in the plywood as
required.
NOTE: Plywood should equal the
thickness of the drywall (½" minimum).
B
Fasten plywood
securely to at
least (3) studs.
A
Use 3⁄8" lag screws and square washers provided to secure
the frame to plywood (5) places. Shim frame as necessary.
NOTE: Other fasteners may be used based on wall material.
D
Plywood Mounting Height "A" Dimension
Standard Height 19" (483mm)
TAS, Grades 6 through 8 or 9 17" (432mm)
TAS, Pre-K through Grades 5 or 6 15" (381mm)
Juvenile Height 16" (406mm)
Shim the frame at anchor
points to ensure the offset
bracket is straight. Leave
the top screw loose.
C
Minimum required to
pick up three studs and
vertical frame members
–33½" (851mm) min.
Mount the faucet boxes
onto the brackets with
valve positioned toward
the wall (if applicable).
A
Hang the faucet box brackets onto the frame
in the orientation shown. Piping connection of
box should point toward the back of the unit.
B
26"
(660mm)

LVRD2 Installation
87/25/2018 Bradley • 215-1669 Rev. K; ECN 18-08-010A
4Faucets and Optional Soap Valve
For ease of installation, leave the bowl laying on
its back. Install the faucets and optional soap
valves according to manufacturer's instructions.
Bradley Model 6315 Soap Dispenser is shown.
3Drain Assembly
For ease of drain installation, lay the
bowl on its back.
O-Ring
Drain Adapter
Packing Washer
#10-24
Screw

Installation LVRD2
Bradley • 215-1669 Rev. K; ECN 18-08-010A 7/25/2018 9
5a Bowl Mounting (to Frame)
Washer
¼"-20
Screw
5b Bowl Mounting (to Wall)
Reinforce behind the wall
at the two bowl mounting
locations, then secure the
bowl to the wall.
A
Press firmly on the back
of the bowl to seat the
bowl into the frame.
Tighten the top screw on
the frame.
A
Bowl is heavy!
Water supply to battery box solenoid MUST be supplied
using a plastic hose (provided by Bradley).
Cold
Hot
Optional TMV Valve
(½" NPTM Outlet)
Connect faucet hoses. Slide
through keyhole slots from behind.
Plastic
Hose Plastic
Hose
Stainless
Steel
Hose
TMA Option
Plastic
Hose
Plastic Hose
Stainless Steel
Hose
NONE Option

LVRD2 Installation
10 7/25/2018 Bradley • 215-1669 Rev. K; ECN 18-08-010A
Strainer
6Strainer and P-trap
Thread the strainer screw
through the boss on the
drain adapter and secure
the strainer to the bowl.
B
Attach the strainer
screw to the strainer.
Do not overtighten.
A
7Adjust Temperature with Water Running
H
C
ALoosen Cap Screw about 1/4" (4-6 turns)
and lift up cover (do not remove).
BUsing cover, turn cartridge gently until
desired water temperature is reached. Do
not turn past stops as this may damage
unit. Push cover down and tighten screw.
This valve is NOT factory preset.
Upon installation, the temperature
of this valve must be checked and
adjusted to ensure delivery of a
safe water temperature. Water
in excess of 110°F (43°C) may
cause scalding.