BROSA Elizabeth Sideboard User manual

ASSEMBLY GUIDE
Elizabeth Sideboard
v1.0

Components
Upon unpacking your sideboard from its delivery box, you should have the
separate pieces shown below. Follow the steps on the next pages to assemble
your new sideboard.
Sideboard x 1
Shelf x 1
Leg x 2
Leg x 1
Leg x 2
Hardware
What you need
aa x 2
Spec:
bb x 1
Spec:
cc x 2
Spec: Ø4 x 17mm
D x 4
Spec: Ø8.4 x 2mm
E x 4
Spec: M8 x 13mm
F x 1
Spec:
G x 4
Spec:
A x 4
Spec: M8 x 12 x 30mm
B x 4
Spec: M8 x 60mm
C x 4
Spec: Ø8 x 17 x 1.6mm

Step 1 1.1 Insert a cross dowel (A) into the hole at the top of
each leg (2 & 3) making sure it sits facing the correct way.
1.2 Insert a threaded bolt (B) into the hole on the side of
each leg (2 & 3) screwing it tightly in place.
A x 4
B x 4
Step 1.2
Step 1.1

Step 2 2.1 Align a leg (2 or 3) to the underside of the sideboard
(1) making sure the threaded bold (B) protruding from
the leg ts into the hole in the frame. Fit a at washer
(C) to the bolt (B) followed by a lock washer (D) and a
nut (E) using the spanner (F) to tighten the nut in
place. Repeat for the remaining legs (2 & 3).
2.2 Align leg (4) to the center of underside of the
sideboard (1) and screw tightly in place.
Step 2.1
Step 2.2
E x 4
C x 4
D x 4
F x 1

Step 3 3.1 With another person, gently lift the sideboard and
place upright on a level surface.
3.2 Insert a shelf supporter (G) into each desired hole
inside the unit, making sure that they are all level.
3.3 Tilt the shelf (5) to a suitable angle and slide it into
the unit, rst making sure that the holes on the shelves
are facing down so that the pins on the shelf
supporters (G) t inside.
Enjoy your new sideboard!
G x 4
Step 3.2
Step 3.3
Step 3.3
Step 3.1

Step 4 e following steps are to instruct how to adjust the
hinges if needed.
4.1 Lateral adjustment by screw adjustment.
4.2 Front-to-Back by slackening and retightening the
hinge-arm mounting screw.
4.3 Vertical adjustment via slots on mounting plate by
slackening and retightening the screws on the
mounting plate.
Step 4.1 Step 4.2
Step 4.3

Step 5 e following steps are to instruct how to vertically
adjust the drawers if needed.
5.1 Both of the drawers have (give or take) a 2.5mm gap
on top and bottom of each drawer.
5.2 To vertically adjust, twist the third tab inside the
drawer to move the front panel up or down.
Step 5.1
Step 5.2

Step 6 e following steps are to instruct how to apply the anti
tip kit (which is optional, but recommended).
6.1 Align the mounting bracket (aa) to the back of the
sideboard and secure in place with the screws (cc).
6.2 At the location the sideboard will be placed, mark
out two holes on the wall for the other bracket (aa) and
using a drill form the holes. Warning: check the wall for
hidden pipes and cables before drilling holes. Attach
the mounting bracket (aa) to the wall with suitable
plugs for your wall type. read the nylon strap (bb)
through both of the backets and secure rmly.
aa x 2
bb x 1
cc x 2
Step 6.2
Step 6.1