BROSA Baker Wide Sideboard User manual

ASSEMBLY GUIDE
Baker Wide Sideboard
v1.0

Components
A x 12
(Shelf Support)
Hardware
What you need
Middle Shelf x 1
Side Shelf x 2 Body x 1
Before you get started, check you have all of the pieces below. If anything’s
missing, please visit www.brosa.com.au/pages/product-return-and-parts-request
and we’ll sort it out right away.
1
2
3

Step 1
A x 2
Step 1.1
Step 1.2
Step 1.3
1.1 Insert a pair of shelf supports (A) into the holes
on the side of hinges inside the compartment.
1.2 Fit a side shelf (2) into the inner space. Tilt the
shelf properly so that it goes in.
1.3 Fit the projections on the supports into the holes
beneath the shelves.
1
2
A

Step 2
A x 2
2.1 Lift the unxed side of the shelf up to make room
for the supports.
2.2 Insert the second pair of supports (A) into the
holes on the opposite side inside the compartment.
2.3 Lower the shelf until it rests securely on all four
supports.
Step 2.1
A

Step 3
A x 8
Repeat Step 1 and Step 2 for the rest of the shelves.
Make sure begin with the sides of hinges.
2
3

Step 4 Enjoy your new sideboard!

Door Adjustment
Identify the hinge types on your door(s) and then choose the right plan to
adjust the hinge(s).
1. 90° Hinge Adjustment

2. 180° Hinge Adjustment

1. Door Adjustment
Drawer door could be adjusted vertically by ±2.5mm. Turn the knob under-
neath the drawer to adjust the vertical position so that there are equal gaps
above and below the front panel.
+2.5
-2.5
Drawer Adjustment

2. Drawer Uninstallation
To take the drawer out, open it, pull the lock button underneath the drawer
base panel [1]. Gently lift the front part of the drawer so that the brackets at
the front of the runners separate from the holes on the side panels of the
drawer [2]. Slide the drawer out of the brackets at the back of the runners [3].
1
23
12
3

3. Drawer Installation
To put the drawer back in, place the drawer upon the runners and t the
brackets at the back of the runners into the holes of the drawer [1]. Gently put
down the front part of the drawer so that the brackets at the front of the run-
ners t into the holes on the side panels of the drawer [2]. Push back the lock
button underneath the drawer to secure the drawer in place [3].
1
2
3
1
2
3

Wall Fixings
Because of the variety of wall compositions, we can’t provide you with appro-
priate wall xings. Please identify your wall composition and contact your
local hardware store to get the approriate xings.
Standard Tip Kit Installation
Hardware
aa x 2
(Mounting Bracket)
Tape Measure Pencil Drill
bb x 1
(Nylon Strap)
cc x 2
(Flat Head Screw)
(Ø4 x 17)
Wood
If xing to wood
make sure that it isn’t
chipboard as screws
can easily pull away
from the core struc-
ture.
Brick or Masonry
Use an appropriate
wall plug provided
you are sure your
wall is sound.
Cavity Wall
Special toggle wall
plugs are needed.
Seek expert advice.
What you need

1. Using the short screws (cc) attach a bracket (aa) to the back of the piece of
furniture’s top.
aa x 1
cc x 2
aa
cc

2. Determine where the piece is to be placed and using the pencil mark loca-
tion on the wall for the mounting bracket. ey should be placed approxi-
mately 2.5cm below the mounting bracket secured to the back of your furni-
ture.
Use appropriate xings to fasten the bracket (aa) onto the wall.
2.5cm
aa x 1
aa

3. Lace the nylon strap (bb) down through the brackets. Slide the thin end of
the strap through the receiving end on the nylon strap. Pull to tighten the
piece of furniture snug against wall.
bb x 1
bb