BROSA Dominic Wide Bookcase User manual

Dominic
Wide Bookcase
ASSEMBLY GUIDE
V1

FOR YOUR SAFETY
Lift, don’t drag. This protects
your floor and product.
Avoid loose screws. Tighten
fixtures every few months.
Assembly requires 2 people.
It's always easier with a
friend.
Contact our support online
or call 1300 027 672.
Check the assembly guide
for required components.
?
Assembling this product on
a soft surface protects its
finish.

Components
Before you get started, check you have all of the pieces below.
If anything’s missing, we’ll sort it out right away. Simply visit:
www.brosa.com.au/pages/product-return-and-parts-request
Hardware
A x 8
(M6 x 20)
C x 27
(M5 x 30)
E x 1
(M6)
D x 6B x 2
(M6 x 16)
Shelf x 3
④
Inner Brace x 2
⑤
Right Stand x 1
①
Middle Stand x 1
②
Left Stand x 1
③
Outer Brace x 2
⑥

What You Need
Identify the face where the slats of the wooden
crate are fixed by the screws. Untighten the
screws using a screwdriver to remove the slats on
top of the frame.
Step 1
To prevent the components from damage during transport, an extra
wooden crate has been applied. Follow Step 1 and Step 2 below to
unbox the product.

Step 2 Lift the carton out of the wooden crate and place
it on a level surface. Unbox the components to
get ready for assembly.

Attach the felt pads D to the bottom of the
stands ① ② ③.
Step 3
Dx 6
D
①
②
③

Line up the stands ① ② ③. Make sure that the
bolt holes are facing each other as shown in the
diagram below.
Step 4
①
②
③

The edge of each shelf ④ is beveled. Make sure
you recognise the narrow face of each shelf and
place the narrow face on top.
Step 5
8
2
°
This
way
up
④

With friends holding the stands, rest a shelf upon
the rails of the stands. Make sure the columns of
the stands run through the slots of the shelf.
Step 6

Slant another shelf and run it through the
structure formed in Step 6. Flip it horizontal once
the slots match the columns. Now you can rest it
upon the rails.
Step 7

Repeat Step 7 for the other shelf.
Step 8

Note: It is important to install the inner brace first.
Pay attention to distinguishing the inner brace
from the outer brace in this step.
Inner brace ⑤ has a smaller threaded hole in the
centre while the outer brace ⑥ has a bigger
unthreaded hole.
Step 9
Inner Brace
⑤
Outer Brace
⑥

Align an inner brace ⑤ with diagonal bolt holes
on the columns. Insert the long bolts Ainto the
holes and screw them with your hand. Leave the
bolts loosely attached.
Repeat this for the other half of the structure.
Step 10
Ax 4
⑤
⑤
A
A

Align an outer brace ⑥with the other diagonal
bolt holes. Insert the long bolts Ainto the holes
and screw them with your hand. Leave the bolts
loosely attached.
Repeat this for the other half of the structure.
Step 11
Ax 4
⑥
⑥
A
A

Insert a short bolt Binto the centre hole of the
outer brace and make it grab the threads of the
inner brace.
Repeat this for the other half of the structure.
Step 12
Bx 2
B

Once the braces are fixed in place, tighten all
bolts with the Allen key E.
Step 13
Ex 1
E
E

Lay the formed structure on a protected surface.
Insert the screws C into the holes on the bottom
and drive them into the bottom of the shelves
with a drill or screwdriver. This might need a fair
amount of strength as there are NO pre-drilled
holes on the solid wood shelves to receive the
screws.
Step 14
Cx 27
C

Flip the completed piece of furniture and place it
upright in its desired location. Enjoy your new
Dominic Wide Bookcase!
Step 15

It is not mandatory but strongly recommended to install anti-tip kit for
safety.
Anti-Tip Kit Installation
Hardware
Wall Fixings
aa x 2
Wood
If fixing to wood
make sure that it
isn’t chipboard as
screws can easily
pull away from the
core structure.
Brick or Masonry
Use an appropriate
wall plug provided
you are sure your
wall is sound.
Cavity Wall
Special toggle wall
plugs are needed.
Seek expert
advice.
Wall fixings are NOT included since different wall materials require
different types of fixing devices. Use fixing devices suitable for the
walls in your home. For advice on suitable fixing systems, contact your
local hardware store.

Fit the brackets aa over the back columns of the stands. Fix the
brackets with appropriate wall fixings.
aa x 2
Wall fixings are not
included. Contact
your local hardware
store for appropriate
fixing devices.
aa