Burkert 2610 User manual

Bedienungsanleitung
Manuel d‘utilisation
Operating Instructions
Type 2610, 2612, 2620
2/2-way valve
2/2-Wege-Ventil
Vanne 2/2 voies
Type 2610

2
2 INTENDED USE
Incorrect use of the solenoid valve Type 2610, the piston
actuated valve Type2612 and the diaphragm actuated valve
Type2620 can be dangerous to people, nearby equipment and
the environment.
The device is designed for blocking, dosing, lling and venting
gaseous and liquid media.
▶Use according to the permitted data, operating conditions and
conditions of use specied in the contract documents and oper-
ating instructions.
▶Correct transportation, correct storage and installation and careful
use and maintenance are essential for reliable and problem-free
operation.
▶Use the device only as intended.
▶Check media resistance.
2.1 Denition of term
In these operating instructions, the term “device” always refers to
the solenoid valve Type 2610, the piston actuated valve Type2612
and the diaphragm actuated valve Type2620.
1 OPERATING INSTRUCTIONS
The operating instructions contain important information.
▶Read the operating instructions carefully and follow the safety
instructions in particular, and also observe the operating conditions.
▶Operating instructions must be available to each user.
▶The liability and warranty for the Type 2610, Type 2612 and
Type2620 are void if the operating instructions are not followed.
1.1 Symbols
▶Designates an instruction to prevent risks.
→Designates a procedure which you must carry out.
Warning of injuries:
DANGER!
Imminent danger! Serious or fatal injuries.
WARNING!
Potential danger! Serious or fatal injuries.
CAUTION!
Danger! Minor or moderately severe injuries.
Warns of damage to property:
NOTE!
english

3
2.2 Insulation
Type 2610, 2620:
The device must not be insulated more
than 2 cm from the edge of the body
upwards to the actuator.
max. 2 cm
3 BASIC SAFETY INSTRUCTIONS
These safety instructions do not make allowance for any contin-
gencies
and events which may arise during installation, operation and
maintenance.
Risk of injury from high pressure.
▶Before loosening the lines and valves, turn o the pressure and
vent the lines.
Risk of electric shock.
▶Before reaching into the system, switch o the power supply
and secure to prevent reactivation. Observe applicable accident
prevention and safety regulations for electrical equipment.
Risk of burns or risk of re.
During continuous operation or hot media the surface of the
device may become hot.
▶Keep the device away from highly ammable substances and
media and do not touch the device with bare hands.
▶Do not obstruct the heat release required for operation.
Danger due to high and low temperatures.
The device may become extremely cold or hot depending on the
temperature of the media.
▶Keep away from ammable and cold-sensitive substances and
do not touch with bare hands.
Risk of injury from hot, cold and aggressive media.
Heat sources or temperature uctuations may cause malfunc-
tions or leaks.
▶Avoid heat sources which may cause the permitted temperature
range to be exceeded.
▶Before use, check media resistance.
english

4
Destruction of the coil by overheating (only Type 2610).
▶Connect the coil electrically only when the body has been installed.
▶In the case of AC voltage pay attention to movable core.
▶Check media resistance.
General hazardous situations.
To prevent injury, ensure that:
▶Do not feed in aggressive or ammable media.
▶Do not make any internal or external changes.
▶Ensure that the system cannot be activated unintentionally.
▶Installation and repair work may be carried out by authorized
technicians only and with the appropriate tools.
▶After an interruption in the power supply or pneumatic supply,
ensure that the process is restarted in a dened or controlled
manner.
▶Do not put any loads on the body.
▶The general rules of technology apply to application planning and
operation of the device.
4 TECHNICAL DATA
The following values are indicated on the type label:
• Type 2610: voltage, current type, coil power consumption
Type 2612, 2620: pilot pressure
• Pressure range
• Body material (MS=brass, VA=stainless steel)
• Seal material (PTFE, NBR)
4.1 Conformity
Type 2610 conforms with the EU Directives according to the EU
Declaration of Conformity (if applicable).
4.2 Standards
The applied standards, which verify conformity with the EU Directives,
can be found on the EU Type Examination Certicate and / or the EU
Declaration of Conformity (if applicable).
4.3 Operating conditions
Ambient temperature
Type 2610 max. +50 °C
english

5
Type 2612, 2620 max. +90 °C
max. +55 °C with attached pilot valve
Degree of protection
Type 2610 with cable plug: IP65 in accordance with EN
60529,
NEMA 4X
4.4 Fluidic data
Medium temperature
Type 2610, 2620 –200–+180 °C
Type 2612 –10–+90 °C
Viscosity 21 mm²/s
Media neutral gaseous and liquid media, which do
not attack body and sealing materials (see
table of resistance under www.buerkert.de).
Check media resistance in individual cases.
Pilot media
Type 2620 neutral gaseous and liquid media, air, water,
hydraulic uids up to max. 90 °C
Circuit function (CF) Type 2610
Circuit function
A
(NC)
1 (P)
2 (A)
2/2-way valve, 1 (P) nor-
mally closed
Circuit function (CF) Type, 2612, Type 2620
Circuit function
A
(NC)
1 (P)
2 (A)
2/2-way valve, normally
closed by spring action
Circuit function
B
(NO)
1 (P)
2 (B)
2/2-way valve, normally
open by spring action
Circuit function I
1 (P)
2 (A)
2/2-way valve, double-
acting diaphragm actuator,
any direction of ow
english

6
0
0
2
4
6
8
10
10 20 30 40 50
CF A DN 4, 6 and 8
CF B and CF I DN 4,6 and 8
Operating
pressure
Pilot pressure [bar]
Type 2612 4.5 Mechanical data
Port connections
Type 2610, 2620 G1/4, G1/2
Type 2612 Flange
Materials
Body:
Designation MS Body: brass, seat: 1.4305 (G1/4)
Body: brass, seat: brass (G1/2)
Designation VA Body and seat: 1.4410
Actuator
Type 2610, 2620 Epoxy
Type 2612 Aluminium
Metal bellow
Type 2612, 2620 1.4541
Seal material
Type 2610, 2620 PTFE
Type 2612 NBR
Dimensions
Type 2610 see data sheet
english

7
Type 2612
32
∅3,7
∅6,3
M4
62,7
67,4
5,6 7
27,9
M5
24
Type 2620
∅6,3 15,5
14
58,6
G1/8
G1/2
G3/8 G1/4
173,6
187,6
185,6
174,6
∅6,3
34
8,5
14 SW27
45 45
34
37
74,5
56
12
37
english

8
4.6 Electrical data (only Type 2610)
Connections DIN EN 175301-803 Form A:
for cable plug Type 2511
Operating voltage see type label
Voltage tolerance ± 10 %
Power consumption 4 W operation, 72 W inrush
Switching frequency max. 10/min
O-time taus between
2 switching operations min. 1 s
4.7 Type label (example)
Identication number
Type 2610: voltage, frequency, power consumption
Type 2612, 2620: pilot pressure
Port connection,
pressure range
Type
Circuit function
Orice Seal material
Body material
2610 A 6,0 PTFE VA
Made in Germany
00167737 W17MG
24 V AC/DC 72/4W
G1/4 PN 0 - 10 bar
english

9
5 INSTALLATION
DANGER!
Risk of injury from high pressure in the equipment.
▶Before loosening the pipes and valves, turn o the pressure and
vent the lines.
Risk of injury due to electrical shock.
▶Before reaching into the device or the equipment, switch o the
power supply and secure to prevent reactivation.
▶Observe applicable accident prevention and safety regulations
for electrical equipment.
WARNING!
Risk of injury from improper installation.
▶Installation may be carried out by authorized technicians only and
with the appropriate tools.
Risk of injury from unintentional activation of the system and
an uncontrolled restart.
▶Secure system from unintentional activation.
▶Following assembly, ensure a controlled restart.
5.1 Fluid installation
Installation position: any, preferably magnetic system or actuator
upright.
→Check pipelines and ange connections for dirt and clean.
→Install a dirt lter before the valve inlet (0.2–0.4 mm).
Observe direction of ow. The arrow on the body indicates
the direction of ow.
Arrow indicating
direction of ow
Type 2610
Type 2620
NOTE!
Caution risk of breakage.
▶Do not use the coil or the actuator as a lever arm.
→Threaded connection: Hold the device with a open-end wrench
on the body and screw into the pipeline.
english

10
Flanged connection:
WARNING!
Risk of injury from escaping medium.
▶Leaking connections if seals not seated properly, if manifold
uneven or if surface quality of the manifold inadequate.
▶Make certain the seals included with delivery are properly
seated in the valve.
▶Ensure that the manifold is even.
▶Ensure that the surface quality of the manifold is adequate.
→Remove the cover plate.
→Insert the seal into the valve.
→Screw the body onto the manifold.
5.2 Electric installation (only Type 2610)
WARNING!
Risk of injury due to electrical shock.
▶Before reaching into the system, switch o the power supply
and secure to prevent reactivation.
▶Observe applicable accident prevention and safety regulations
for electrical equipment.
If the protective conductor contact between the coil and body is
missing, there is danger of electrical shock.
▶Always connect protective conductor.
▶Check electrical continuity between coil and body.
Operate the device only with the cable plug included in the
scope of delivery.
Note the voltage and current type as specied on the type
label.
→Check that seal is tted correctly.
→Screw cable plug tightly onto coil
(min. 0.5 Nm, max. 0.8 Nm).
english