Cisco SX80 User manual

Page 1 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
SX80 with Touchpad 10
User Guide
Rev 29Apr2019

Page 2 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
Table of Contents
OVERVIEW .....................................................3
BASIC NAVIGATION ..............................................4
GENERAL USE ..................................................5
Setup ......................................................................5
Camera Controls .............................................................6
Microphone..................................................................8
Volume .....................................................................9
Site to Site Calls ..............................................................9
Connecting to an MBT Site............................................................ 9
Connecting to a site outside the MBT Network ............................................ 10
Far End Control: Site to Site .......................................................... 10
Sharing Presentation: Site to Site ...................................................... 11
Screen Layout: Presentation - Site to Site ............................................... 11
Recent Calls and Favourites ....................................................12
Multi-Site Event Calls (MCU) ....................................................13
Connecting to a Multi Site (MCU) Call ................................................... 13
Screen Layout/Far End: No Presentation - Multi-Site ....................................... 14
Sharing Presentation: Multi Site ....................................................... 14
Screen Layout: Presentation - Multi Site ................................................ 15
Receiving and Ending Video Calls ................................................16
DUAL VIDEO ENABLED EQUIPMENT ................................17
TROUBLESHOOTING .............................................18
ADDITIONAL TRAINING INFORMATION ..............................19
VIDEOCONFERENCING ETIQUETTE ................................19

Page 3 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
This user guide will provide you with an overview and the knowledge to setup and use the SX80
videoconference solution and the Touchpad 10
Camera: high quality imaging device which
transmits images to the screen/monitor. The
camera movements are controlled by a wireless
infra-red (IR) remote control that controls a
variety of functions, both on the near and far
end.
OVERVIEW
The main components included with the SX80 and Touchpad 10 are the Camera, Codec, Ethernet Cable,
Microphone, Screen/Monitor and Touchpad. In some instances there may also be a router.
Codec: central part of the videoconferencing
equipment. The main task of the codec is the
compression of outgoing video, audio and data, the
decompression of the incoming information and the
transmission of this information between endpoints.
The name codec comes from a combination of the
two words compression and decompression.
Touchpad 10: used to place calls, adjust the volume,
navigate screens and select options. It controls
all functions of the videoconferencing equipment,
including moving the camera.
Screen/Monitor: built-in screen/monitor displays
the far end or the near end image and content as
selected by the user.
Main Components

Page 4 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
BASIC NAVIGATION
The Touchpad 10 is used to operate your video equipment and the system will not work without it. Here are
some commonly used features:
Basic Features of the Touchpad 10
General Use
Tap the Camera icon to
activate self-view and
camera settings.
Tap to Share content
outside of a call.
Tap Microphone
to mute/unmute
the microphone.
Press and hold the left side of the Volume
button to decrease the volume and the right
side to increase the volume.
Call (access
to Directory/
Favourites)
Tap the touchpad to wake
up the system if needed.
Tap a button to activate it’s
function.
Scroll in lists as on a smart
phone.
Tap the touchpad to wake
up the system if needed.

Page 5 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
GENERAL USE
The following sections will provide instructions for using your SX80 and Touchpad 10 solution to place
and receive videoconference calls.
Setup
Setup and Use the Equipment
Selfview
Wake the codec by tapping the touchpad and turn on the video screen/monitor if required. In a few seconds
you will see the home screen.
Before the meeting starts we recommend that you check the selfview. The selfview displays an image of
your camera view on screen and shows you what you will be sending to the other site. The selfview appears
as a PIP (Picture-in-Picture).
Outside a call:
During a call:
Tap Selfview to turn it on.
You may now maximize/
minimize, turn selfview
o󰀨, or tap Camera to
control your own camera.
Tap anywhere outside the
menu to exit.
Selfview
Tap anywhere outside the
menu to exit.
Tap Camera .
Tap Camera (a) and then tap
Selfview (b) to turn it on (you
may now resize the selfview
image or control the camera).
a
b

Page 6 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
The camera controls allow you to manually control the zoom, pan and tilt of the camera as well as dene
Camera Presets.
Camera Controls
Adjust Camera Manually
Move the Selfview PiP Box
Tap and hold the Selfview image. The selfview image will now turn blue. You will
also see the alternate positions available for the
selfview image. Keep holding the image.
Release the image by lifting your nger
from the screen. The selfview image has
now assumed its new position.
Drag the image to a new position, shown
here is the upper left corner.
Tap Camera to invoke the
camera adjustment menu.
Tap the desired
Camera Preset.
Turn Selfview
On and O󰀨.
Maximize/minimize
Selfview.
Pan/tilt controls.
(arrows)
Zoom in and out
(+/-).

Page 7 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
Use Camera Presets
Add a New Preset
Camera presets are useful when images from many di󰀨erent camera positions and video sources are to
be viewed by the far end site(s). Presets are used to switch camera positions quickly and easily without
having to manually move the camera.
Tap Add New and then tap
in the text eld.
Tap Save to leave the menu putting changes into
e󰀨ect, or tap Cancel to leave menu and undo the
changes (tap anywhere outside the menu when
you’re done).
Key in a descriptive name.
Selfview will be activated
automatically. Use the arrows and
zoom +/- to adjust the camera to
the desired position.
Tap Camera to invoke the
camera adjustment menu.
Tap Camera to access the
Camera Presets (positions).
Tap the desired preset and then tap anywhere
outside the menu to exit.

Page 8 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
Modify Existing Preset
Standard Presets
Mute and Unmute the Microphone
The SX80 with Touch 10 is set up with three (3) Standard Presets: Camera presets will be set up and
saved as part of equipment implementation but there may be a need to change or resave presets.
Sign – shows the site’s sign with their site name. This is an o󰀨 screen camera view that allows
users to move about the room without being on camera and identies the sites that are
connected.
Participant (Presenter/Provider/Patient) – close up view of the person or persons involved in the
event. Whether it is the patient, provider or a presenter, when setting this preset, you want to
ensure that the far sites are able see the person clearly.
Room –shows a view of everyone in the room. By setting a preset of the entire room, you can
easily identify everyone in attendance and then switch back to the participant preset as
necessary. This preset is also helpful for question and answer periods.
Microphone
Tap Camera to access the
camera menu.
Tap the preset to be edited. Selfview
will be activated automatically.
Use the arrows and zoom
+/- to adjust the camera.
Tap the little arrowhead of
the preset to be edited.
Tap anywhere outside the
menu to close it.
Tap Update to Current Position.
to put your changes into e󰀨ect.
To delete an existing preset tap Remove.
Mute and unmute the microphone.
Green Unmuted (site can hear you)
Red Mute (site cannot hear you)

Page 9 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
Adjust the Volume
TIP
Connect to an MBT Site
Volume
Site to Site Calls
Connecting to an MBT Site
If you call the same sites from the same equipment you can save the contact
to the favourites list on that equipment. The next time you need to call the site,
tap Call, and then tap Favorites to locate the site rather than scroll through the
entire address book.
Tap Call.
Tap Call to connect.
Tap End to disconnect.
Tap in the search/dial eld to invoke
the keypad. (Tap the keypad icon in
the bottom left corner of the screen if
required.)
Type in the 5 digit number.
Use the
ABC/123
key to toggle
between alpha
and numeric.
Press and hold the left side of the Volume button to decrease the volume and the
right side to increase the volume.
The Home screen should always be displayed prior to connecting to a site; if not, this may mean that
a previous call was not disconnected. If you do not see the Home screen, press End to disconnect
prior to connecting to your site.
...
...
...
.

Page 10 of 19
MBTelehealth - SX80 with Touchpad10 User Guide
Connect to a Site Outside the MBT Network
Connecting to a site outside the MBT Network
Far End - Site to Site
Taking far end camera control allows you to move the camera at the far end site. Before taking control,
always request permission rst. You may need to take far end camera control if the person on the other
end is unable to operate their own camera.
Far End Control: Site to Site
In a call, tap the
Participants icon in
the top right corner
to invoke the list of
participants.
Tap the site whose
camera you want to
control.
Tap Camera. Adjust the remote camera. Tap
anywhere outside the camera
control buttons when you’re done to
return to near end (control of your
own camera).
Tap Call.
Tap Call to connect.
Tap End to disconnect.
Tap in the search/dial eld to invoke
the keypad. (Tap the keypad icon in
the bottom left corner of the screen if
required.)
Type in the phone number.
Use the
ABC/123
key to toggle
between alpha
and numeric.
...
...
...
.