Connects2 CT53-PO05 User manual

CT53-PO05
Active System Adapter
for Porsche Vehicles
APPLICATION
FEATURES
Porsche 911 (997) 2004 - 2008
• Retains MOST 25 Fiber Amplied System
• Provides Outputs for Park Brake, Reverse Gear, Speed Pulse & Amp Remote
The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s. This
instruction manual is based on documented data and research. The manufacturer of this product cannot be held responsible for any changes made to the
vehicle by the manufacturer or damages that may occur through the installation of this product in accordance with the steps outlined herein.
Note: Application data is subject to change at any time
DISCLAIMER
For ber-amplied vehicles with MOST 25 systems and quadlock connectors.
CT53-PO05_V1
vi
ii
i
i. Amp Retention Interface
ii. Male RCA Connectors
iii. Flying Wires
iii iv v
iv. Male ISO Connector
v. Quadlock Connector
vi. Interface Box

2CT53-PO05_V1
PRIOR TO INSTALLATION
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation
must be free of moisture and away from heat sources. Please ensure that the correct tools are using during the
installation to avoid damage to the vehicle or product. Connects2 can not be held responsible for the installation
of this product.
Note: The aftermarket stereo being installed must have RCA connections in order for this product to
function correctly
IN MALE ISO CONNECTOR
Purple Right Rear Speaker +
Purple/Black Right Rear Speaker -
Green Left Rear Speaker +
Green/Black Left Rear Speaker -
Grey Right Front Speaker +
Grey/Black Right Front Speaker -
White Left Front Speaker +
White/Black Left Front Speaker -
ADDITIONAL CONNECTIONS
Pink Speed Pulse
Green Park Brake
Purple/White Reverse Gear
Blue/White Amp Remote
WIRING KEY
Yellow Permanent 12V
Black Ground
Red Ignition 12V
Orange Illumination
iv
iii

3
Need help? Visit support.connects2.com/tickets/technical
CT53-PO05_V1
INSTALLATION GUIDE
Before installing the interface, the factory stereo must be removed and disconnected. To do this, please consult
the vehicle owner’s manual/handbook or contact a tting professional.
See wiring diagram on Pg.4 for more information
1. Connect the 14 Pin connector from the supplied wiring loom to the interface box
4. Connect the male power/speaker ISO connector to the female power/speaker ISO connector from the
aftermarket stereo.
NOTE: For aftermarket stereos which do not have an ISO connector, please see “Wiring Key” on Pg.2 for information on which wires to
connect. Some interfaces may also have additional ‘flying’ wires which can be connected to the vehicle to support various features
ie. parking brake trigger, reverse gear and speed pulse. Details of these can be found under ‘Additional Connections’.
6. Connect the female vehicle specic connector/s on the supplied harness to the male vehicle specic
connector/s from the vehicle. Please refer to wiring diagram on Pg.4, or cover photo on Pg.1 for more
information on the connector style of this interface. Common styles include Mini ISO or Quadlock.
7. Test stereo and steering wheel control functionality for correct operation before reassembling the
vehicle dashboard. If steering wheel control functions are unresponsive, please uninstall the interface and
wiring and reinstall carefully in accordance with the above steps.
For further help and support, please contact us directly at support.connects2.com/tickets/technical and ll out a
support ticket with the full details of your issue.
vi
iv
v
2. Connect the amplier retention interface to the 8 Pin connector on the supplied wiring loom
3. Remove the plastic dust cover from the amplier retention interface and plug in the vehicle’s ber
amplier connection
i
5. Connect the male red and white RCA connectors to the female inputs on the back of the aftermarket
stereo
ii

4CT53-PO05_V1
WIRING DIAGRAM
Male ISO Connector
Connect to aftermarket stereo
Quadlock Connector
Connect to Quadlock connector from vehicle
Stereo Connection (Patch) Lead Connector [12 Pin]
Connect to Interface Box
Note: Must be connected first, before power
connection is made to the interface
Main Wiring Loom Connector [14 Pin]
Connect to Interface Box
Interface Box
TOWARDS VEHICLE TOWARDS STEREO
Fiber Amplifier Connector
Firstly remove dust cover
from interface
Then connect fiber
amplifier connection
from vehicle
to interface
Male White/Red RCA Connectors
Connect to Aftermarket stereo
Flying Wires
Pink - Speed Pulse
Green - Park Brake
Purple/White - Reverse Gear
Blue/White - Amp Remote