Corriveau Cordoba B101225 User manual

Cordoba gazebo 10'x 12' (20f 8)
Assembly lnstructions
B1 01 225-

Security rules
Warning :
Keep away flame or heat source from gazebo fabrics. Otherwise fabrics can burn or melt and can
cause severe burn on nearby persons. ln this case, material damage has to be considered.
Moreover, the adding of any substance will block or severly slow down capacity of fabric to resist
or be flame retardant.
Regulation
It is the responsability of consumer being in accordance with city regulation, construction code,
zoning or any limitations and obtaining permit prior erecting the gazebo.
Recommendation
Prior to proceed to erect the gazebo, a check-up of quantity of each items should be done. Some
parts may have sharp edges, wearing gloves is recommended.
Figure at least five hours to complete the set-up with two persons. Consider having enough time
for completion of erecting. Even well anchored, a non complete gazebo unit can get or create
damage to nearby environment.
Keep away from any electric installation or transportation device.
A check up of tightening of all bolts should be done all across lifespan of gazebo.
Even if this gazebo is built for year round use, this is strongly recommended to remove snow from
top.
Mosquito net and curtains (optional) must be removed from the unit at freezing period.
lnstruction manual must be read prior start-up of erecting.
All recommendation must be followed carefully to ensure perfect sturdiness of the unit.
Use proper tools and equipements for a safe and compliant installation. Never climb, sit or stand
on structure while erecting.
Anchoring bolts or other anchoring devices are not supplied.
Always recommended to keep instruction manual for further reference.
1

Care
Never use a high pressure washer. Use of mild soap in a lukewarm water is the best solution for
frame only. A clear water rinse is necessary then. Never use soap for fabrics, this will reduce
their capacity and consequently their lifespan and general look. For fabrics, a soft brush and a
lukewarm water is offering an excellent cleaning.
Warranty
Govered
This gazebo is warranty from any manufacturing defect for one year at normal use. This limited
warranty is for one year for parts only.
ln any case a part is needed, please contact the seller giving description and pictures of defect.
Not covered
All damage caused by commercial use, improper care, neglected storage, unreasonable or
abusive use, vandalism, chemical, freeze damage, extreme weather or act of God, rust,
oxidation, stains, improper packaging for return. Normal discoloration and build-up of snow are
not covered either.
Seller :
For each part request, please contact our customer service. lt will need a description of problem,
pictures and consumer invoice copy. Be aware full item code must appear on invoice to give
fabricating period, color and right identification of part requested. This will ensure all proper
information to proceed the request. Moreover, name of person in charge of the request must be
written, name and address of seller ( branch ), e-mail address, fax and phone number.
2

A
Reminder: Before assembly, don't forget to check inside of each Post (No.A),
some parts are well packed and stored inside.
The first Post (No. A)
The second Post (No. A)
A
AAI
X
Y
2
2
2
The tn¡ra Post (No. A)
AC
AD
4
2
L
M
2
2
3

A
Po
AE
-
T
æ=+o
æ=z=R
-U
AV
P
¿,
@B
'F
AE
FE
AD N
H
G
Ft
F
A
A
cc
c
4
{s. B
@3
AW {ag

PARTS LIST:
NO. Description QTY Drawing
APost 4
BBase flange 4
cBase cap 4
DRight brace 4
ELeft brace 4
FLong crossbar 2
Ft Connector 2
GLong crossbar 2
HShort crossbar 2
Ht Connector 2oôoo
Short crossbar 2
JEave profile 2
KEave profile 2
5

NO. Description QTY Drawing
LEave profile 2
MEave profile 2
NCorner roof tube 4
oAir vent roof tube 4
PCorner connector 47¿
oRoof cap 1
RMiddle connector 1
SRoof connector 1
TCorner connector 12
UMiddle connector 6
VAir vent support tube 2
WAir vent support tube 2
XAir vent profile 2
6

NO. Description QTY Drawing
YAir vent profile 2
ZRoof support profile 2
AB Roof support profile 2
AC Middle support tube 4
AD Middle support tube 2
AE Roof support tube 4
AF Roof support tube 2
AG Roof support tube 4
AH Upper roof support
tube 1
AI Upper roof support
tube 2
AJ Air vent panel 2
AK Air vent panel 2
AL Air vent panel 2
7

NO. Description QTY Drawing
AM Air vent panel 2
AN Left roof panel for 12'
side 2
AO Right roof panel for 12'
side 2
AP Right roof panel for 12'
side 2
AQ Left roof panel for 12'
side 2
AR Left roof panel for 10'
side 2
AS Right roof panel for 10'
side 2
AT Left roof panel for 10'
side 2
AU Right roof panel for 10'
side 2
AV Air vent mosquito net 1
AW Mosquito net 1
I

Hardware Kit:
NO. Description QTY Drawing
AA Bolt M6 X 1Smm 182 @
BB Bolt MO X 25mm 42 N
cc Bolt M6 X 42mm 42
DD Bolt M6 X 50mm 4
EE Plastic washer 52
FF Spanner 1
GG Allen key 1
HH M6 Nut 6@
Plastic cap 32
JJ Stake 16
KK Half-thread screw
M6 x 30mm 32
I

eo o
oo
AX4
Bx4 cX4
A-
A
Ap/
I
I
\
CD AA \
I
I
I
I
I
\
c
B
I
B
Step 1:
lnsertbasecap(C)onthebottomofpost(A),thenusingbolts(AA)securebaseflange(B)onthebottomof
post ( A ). Repeat the step for all rest posts. Bolts can be tight completely.
10
o
o
o
o
11

FX2
Fr *2
G*2
G->F t #F
F
G
\
å
_Á&
'-- -aA AA AA AÆ/
GF
Step 2:
lnserttheconnector(F')intoalongcrossbar(G)andalongcrossbar(F)asfigureshown,andsecurewithbolts
( AA ). Bolts can be tight completely.
11
@- ,t'@ .'@
I
@
L
E

HX2
Hr *2
^2
c
Hr H
Attention !!
Do not put bolt in this hole, this care refer to a further step.
H
\
å
Puq AA AA-
\.--.-AA -ÁA- --
IH
Step 3:
lnsertthe connector(H,l )intoa shortcrossbar( l)and a shortcrossbar( H )asfigureshown, and securewith
bolts ( AA ). Bolts can be tight completely.
12
I.@ @
@- .,@ (
I
@
I
I

o
G
F
A
A
\
I--b
\\KK I
KK
A
oKK/
Step 4:
Securelongcrossbarsset(F&G)ontwoposts(A)byusinghalf-thread(KK).Donottightboltscompletelyyet.
Redo same procedure for the opposite side.
13

I
lI\
F
\I
A
A
A
A
A
F
I
\I
KK A
Step 5:
Secureshortcrossbarsset(H&l)ontwoposts(A)byusinghalf-thread(KK).Donottightboltscompletelyyet'
Note : Please check above fig. carefully and make sure all the parts are in right position. For your security, you
may need 4 people for this step.
14

D
E
X4
x4
X32
=G
/F il \
I
AA \l
..-Q a- -A
@ØF
Ø
ØØD
Ø
Step 6:
Secure left and right braces (E & D ) to posts ( A ) by using bolts ( AA ) asfig.1. Do nottight bolts yet. Then
secureotherendofbraces(E&D)toshortandlongassemblycrossbars(FGHI )byusingbolts(AA)asfig.2.
Tightening must be done only once all bolts are located. Tight all loose bolts but following this sequence : external
of corners, lower end of braces then upper end. Prior tightening crossbars, ensure assembly is fully aligned.
1
D
1
Then, install plastic cap ( ll ) as fig. 3 shown
15

o4
X
NX4
o
N
BB B
o\
N
o
N
Step 7:
Secureairventrooftube(O)tocornerrooftube(N)usingbolts(BB)asshowninfig.l.Repeatthisstepfor
remaining air vent & corner roof tubes.
16

X1
S
-- ø
S
l
t\
N
I
i
\
AA F/
NAA
IA
Ø
Ø
Ø
Step 8:
l.Secureassemblyairvent&cornerrooftube(N&O)toroofconnector(S)usingbolts(AA)asshowninfig.l.
Do not tight bolts completely yet.
2.Laydownthecornerrooftubeset(N&O)oncrossbarsfourcornersandsecurebyusingbolts(DD)asshown
in fig.2. Tight corner bolts but not full. 1T

Rx1
--
AA\
ì
I
R
\
oo
Step 9:
Securemiddleconnector(R)toairventrooftube(O)usingbolts(AA)asshowninfig. l
18

ox1
oo
Step 10:
lnsertbolts (AA )through middle connector( R ), and securewith roof cap ( Q ) as shown. Tightbolts.
19