Corriveau Maestrale B101212 User manual

Maestrale Gazebo l0'X 12'(20f 5)
Assembly lnstructions
8101 21 2-

Warning
1. lt is the consumer's responsibility to comply with any building codes, ordinances, zoning
limitations, or local homeowner's restrictions and obtain any required permit, before purchase
and installation of the products.
2.Two to four persons are required for assembly. The tools required includes an Allen key (part
FF in hardware kit instruction), step-ladder and other safety items such as gloves, safety
goggles and hardhat. To avoid injury from exposed sharp edges, it may be necessary to use
the above safety equipment.
3. This unit will take at least 5 hours to set up. You must schedule enough time to complete the
assembly so you don't leave it unattended if not fully assembled, even if bolted to the ground.
. Make sure that all components are in the box. Read instructions carefully before stafting the
assembly.
. Follow all instructions to assure the strength of the shelter.
. ln order to avoid damage to the shelter and its components, use appropriate tools. Do not use
the structure as a support, a step-ladder is recommended.
. Check all screws on a regular basis to maintain the solidity of the structure.
. Keep instructions and parts list for future use.
4. The screws to anchor on wood deck and concrete patio are not included.
Care instructions
. Treat aluminum frame periodically with liquid wax for maximum protection against UV rays and
moisture.
. Mosquito nettings clean with a soft brush and lukewarm water, rinse thoroughly. Dry completely.
. Do not wash nettings with soap as it may remove the protective coating added by the factory.
Attention
. When used in winter, You need to promptly swept snow from the roof
. The mosquito nets must be removed for winter storage.
1

Y
€--
ì\
AB
T
AQ
X
o
Xo J
J
Nñ
oùj \
N:l
IAT
0
AS
E/. J
N
ns\rj
\
¿
g
t¿
AT
AS
E
Fc
D
Bs
ttll'
2
tlll=
Btlll'
AW
ttll'

PARTS LIST:
NO. Description Q'TY Drawing
APost 4
BBase flange 4
cCorner supporter (Right) 4
DCorner supporter (Left) 4
ELong crossbar 2
FLong crossbar 2
GShort crossbar 2
HShort crossbar 2
Corner connector 4
JCorner roof tube 4
KRoof connector 1
LRoof support profile 2
MRoof support profile 2
3

NO. Description Q'TY Drawing
NMiddle roof tube 4
oMiddle roof tube 2
PMiddle connector 1
oUpper roof supporting bar 2
RUpper roof support tube 1
SUpper roof support tube 2
TMiddle roof support tube 4
UMiddle roof support tube 2
VMiddle roof support tube 2
WMiddle roof support tube 2
XAir vent corner connector 4
YRoof cap 1
zStake 16
4

NO. Description Q'TY Drawing
AB Air vent panel 2
AC Air vent panel 2
AD Air vent panel 2
AE Air vent profile 2
AF Air vent profile 2
AG Right roof panel for 12' side 2
À
-
--
:
:
AH Right roof panel for 12' side 2
AI Middle roof panel for 12' side 2
AJ Left roof panel for 12' side 2
AK Left roof panel for 12' side 2-
::-::E
AL Right roof panel for 10' side 2A
:
:
:
AM Right roof panel for 10' side 24
-
-
:
:
AN Middle roof panel for 10' side 2
5

NO. Description Q'TY Drawing
AO Left roof panel for 10' side 2::
-:::'=
AP Left roof panel for 10' side 2::-€
AQ Eave profile 4
AR Eave profile 4
AS Corner moulding 4
AT Center moulding 4
AU Mosquito Net 1
AV Air vent Mosquito net 1
AW Plastic plug 24
6

NO. Description Q'TY Drawing
AA Bolt M6 X 1Smm 164 ÐD
BB Bolt M6 X 30mm 12 C*
cc Bolt M6 X 40mm 26
DD Plastic washer 12
EE Stainless washer 26
FF Allen key 2J
7

AX4
Bx4
A A
'Ð* {
AA
I
\
B
Step 1:
Secure Base flange (B) to the bottom of the Post (A) by using Bolt (AA) as fig. I shown. Repeat the step for
remaining posts.
I
o
o
o

EX2
Fx2
EF
+ -
EF
q
I@
I
o
IIII
I
I
\ /
EF
Step 2:
lnsert Long crossbar (E) into Long crossbar (F) and secure with bolts (AA).
Repeat this step for remaining long crossbars.
I

GIt. x2
Hx2
GH
+ -
GH
@
t@
I
o
II
I
II
AAA
ö
I
\ /
GH
Step 3:
lnsert Short crossbar (G) into Short crossbar (H) and secure with Bolt (AA)
Repeat this step for remaining short crossbars.
10

o
e
AE
o
E
F
A
0o\
A0P
\I
I
I\I
I
l
AF
IAA
'% nn
Step 4:
Secure Long crossbars set (E & F) on two Posts (A) by using bolts (AA). Repeat this step for the
opposite side.
Notes: For the sake of safety, you may need 2 people for this step.
11

'\
FAA --{ F
o
e\--0
A
G
A
Ø
Øo
AA
A
Step 5:
Secure Short crossbars set (G & H) on two Posts (A) by using bolts (AA). Repeat this step for the opposite side.
Notes: Please check above fig. carefully and make sure all the parts in right position. For the sake of safety, you
may need 4 people for this step.
12

cX4
DX4
w^ @
AA
A
AA
q,,/
'..nn@
G
FEc
cA
A
A
Step 6:
Secure Left & Right corner supporters (D & C) to Posts (A) and the crossbars set by using bolts (AA) as fig. 1
shown.
Repeat this step for remaining 3 posts.
13

x4
Jx4
J
T
II
J
,
ê*
J
I
Step 7:
lnsert bolt (AA) through Corner connector (l), secure with the end section of Corner roof tube (J) as fig. 1 shown
Repeat for remaining Corner roof tubes (J).
14

Kx1
AAF
I
Jl¿t
JK
G
AA
F
EG
F
Step I
Secure Corner roof tube sets (J) on the four corners of Crossbars by using bolts (AA) as fig. 1 shown. Do not
tighten the bolts. Then lnsert bolt (AA) through Roof connector (K), secure with Corner roof tube set (J) as fig. 2
shown.
Notes: Do not tighten all bolts till all 4 roof tubes are set.
15

PX1
lr I
PI
o
AA
Step 9:
Secure Middle connector (P) on the Corner roof tube set (J) by using bolts (AA) as shown
16

YX1
J
AA AA
Step 10:
lnsert bolts (AA) through Middle connector (P), and secure with Roof cap (Y) as shown.
17

L
M
x2
x2
J
Maa
I
I
I
L
"ê
I
I
A
AA
Step 11:
lnsert bolts (AA) through Roof support profile (L), and secure with Corner roof tube (J) & Roof support profile (M)
as fig. 1 shown.
18

N
o
X4
x2
N
H
I
@%@
OP
AA @o
ØF
ØG
,fu I
Step 12 -'\ -'/
Secure Middle roof tubes (N & O) on the Roof support profiles (L & M) by using bolt (AA) as fig. I shown. Then
insert bolts (AA) through Middle roof tubes (N & O), secure with the crossbars as fig. 2 & 3 shown.
19