Corriveau lndia 8101202 User manual

lndia gazebo 10 x 12' (2017)
Assembly instructions
Model no: 8101202

READ & SAVE THESE INSTRUCTIONS:
Please read instructions carefully and identify all parts
before assembly.
. Caution: Small parts, like plastic caps, may pose a choking hazard
to young children. Keep out of reach of small children.
. You may require 2-4 persons to do the assembly.
. Do not leave outside during winter. Remove the top during bad
weather.
. Fasten the base to the deck whether it is wood, concrete or others.
. Do not tighten all parts before the assembly is completed.
PART LIST:
NO. FIGURE DESCRIPTION QTY
1Supporting Post 4
2SPost Bottom PIate 4
3Long crossbor 2
4Long crossbor 2
5lnner Connector 4
6ICenter Outer Connector 4
7Short crossbor 2
IShort crossbor 2
IECorner outer moulding 4
10 Center connector 6
11 Corner inside connector 4
12 Short Roof Pole 6
13 Long Roof Pole 4
14 æ=ã# Center Roof Connector 1
15 Bottom supporting tube 2
P1

16 Bottom supporting tube 4
17 Bottom supporting tube 4
18 :Upper supporting tube 2
19 --=4 Upper supporting tube 4
20 =- Upper supporting tube 4
21 Roof cap 1
22 Roof panel B
23 Roof panel B
24 Roof panel 4
25
-
Center supporting profile 2
26
--=!=!t!.
Center supporting profile 4
27 Center supporting profile 4
28 Eave tube 2
29 Eave tube 4
30
-
Eave tube 4
31 sEave Center Connector 6
32 \9 Eave Corner Connector 4
33 rBolt M6 x 15 mm 91
34 n:r SQ HD Bolt M6 x 15 mm 30
35 G@ Bolt M6 x 35 mm 32
36 @Nut M6 30
37 ffi Mosquito Net 1
38 Peg 12
39 JAllen Wrench 1
40 Spanner 1
P2

Step 1.
1). Settle the 4 post bottom plates at the four corners.
2). Connect the post bottom plate (#2) and supporting post (# 1) using bolts (#
33).
21
2
1
1
1
P3

Step 2:
1). lnsert the inner connector (#5) into long crossbar (# 3) and (# 4) using bolts (#33).
Then attach the center connector (# 10) to long crossbars (# 3) and (#4) using
bolts (#33).
2). Attach the center outer connector (# 6) to inner connector (#5) using bolts (# 33).
10 10
34
5
J "J_
È-l-=
4
6
3
34
P4

Step 3:
1). Insert the inner connecto(#s) into short crossbar (#7) and (#8) and align the holes
Secure the center connector (#10) onto inner connector (#5) using bolts (#33).
2). Attach the center outer connector (#6) to inner connector (#5) using bolts (#33).
I
7
8
7
P5

Step 4=
1). Attach long crossbars (# 3, #4) & short crossbars (#7,#8) to the supporting
poles (#1) using bolts (#35).
2). Attach the corner outer moulding (#9) to long crossbars (#3,#4) and short
crossbars (#7,#8) using bolts (#33).
\I
9ü 3I
73
84\
11
1
1
\1
1
P6

Step 5:
1). lnsert two square head bolts (#34) on groove of each short roof pole (#12),
standing by for a further step. Then, insert a square bolt (#34) at end of short
roof pole (#12) and secure to the center roof connector (ffi\ by using nut (#36).
2).Then, use bolt (#33) to combine center connector (#10) and short roof pole (#12).
12
14
12 12
P7

Step 6:
1). lnsert two bolts square head (#34) on groove of each long roof pole (#13),
standing by for a further step. Then, insert a square bolt (#34) at end of long roof
pole (#13) and secure to the center roof connector (#14\ using nut (#36).
2). Then use bolts (#33) to combine corner inside connector (#11) and supporting
post (#1).
13
14
13
13
3
11
11
13 12
P8

StepT=
1). Attach the roof cap (#21) to center roof connector (ffi$ using bolts (#33).
2). Connect the bottom supporting tubes (#15) and (#17) to the protruding bolts (#3a)
from short roof tube (#12\ and secure with nuts (#36)
3). Then connect the upper supporting tubes (#18) and (#20) onto the bolts (#34)
protruding from short roof pole (#12) and secure with nuts (#36).
4). Repeat for the other sides as figure shows.
21
P9

Step 8:
1). Peels off the protective wrapping of the roof panels and notice the sign that
denotes the upside.
2). lnsert roof panel (#22) into the roof pole groove then insert center supporting
profile (#26), then insert roof panel (#23) into the groove.
3). Repeat for other panels as the figure shows.
Note : Do not let the panels slide off.
24
22 7
26
3
7
P10

Step 9:
1). lnsert bolts (#33) into eave center connector (#31), eave tube (#28) and (#29) and
secure onto short roof tube (#12).
2). lnsert bolts (#33) through eave corner connector (#32) and eave tube (#29) and
(#30) onto long roof tube (#13)
3). Repeat for the other sides as figure shows.
30 28 30
29
P11

Step 10:
1). Please ensure the posts and the ground are perpendiculars with each other
once the unit is assembled. Tighten all bolts evenly, use pegs (#38) to fix the
gazebo to the ground firmly.
Depend of patio surface, use proper anchoring devices. Anchors not supplied.
2). Hang up mosquito net (#37) to the "J" hooks of the crossbars.
3). Remove all gazebo assembly stickers.
37
I
3B
1
ø
Ir
P12