Corriveau Maestrale 8101416 User manual

Maestrale Gazebo 10' X14' (201 6)
Assembly Instructions
8101 41 6-

Security rules
Warning :
Keep away flame or heat source from gazebo fabrics. Othen¡rise fabrics can burn or melt and can
cause severe burn on nearby persons. ln this case, material damage has to be considered.
Moreover, the adding of any substance will block or severly slow down capacity of fabric to resist
or be flame retardant.
Regulation
It is the responsability of consumer being in accordance with city regulation, construction code,
zoning or any limitations and obtaining permit prior erecting the gazebo.
Recommendation
Prior to proceed to erect the gazebo, a check-up of quantity of each items should be done. Some
parts may have sharp edges, wearing gloves is recommended.
Figure at least five hours to complete the set-up with two persons. Consider having enough time
for completion of erecting. Even well anchored, a non complete gazebo unit can get or create
damage to nearby environment.
Keep away from any electric installation or transportation device.
A check up of tightening of all bolts should be done all across lifespan of gazebo.
Even if this gazebo is built for year round use, this is strongly recommended to remove snow from
top.
Mosquito net and curtains (optional) must be removed from the unit at freezing period.
lnstruction manual must be read prior start-up of erecting.
All recommendation must be followed carefully to ensure perfect sturdiness of the unit.
Use proper tools and equipements for a safe and compliant installation. Never climb, sit or stand
on structure while erecting.
Anchoring bolts or other anchoring devices are not supplied.
Always recommended to keep instruction manual for further reference.
1

Care
Never use a high pressure washer. Use of mild soap in a lukewarm water is the best solution for
frame only. A clear water rinse is necessary then. Never use soap for fabrics, this will reduce
their capacity and consequently their lifespan and general look. For fabrics, a soft brush and a
lukewarm water is offering an excellent cleaning.
Warranty
Covered
This gazebo is warranty from any manufacturing defect for one year at normal use. This limited
warranty is for one year for parts only.
ln any case a part is needed, please contact the seller giving description and pictures of defect.
Not covered
All damage caused by commercial use, improper care, neglected storage, unreasonable or
abusive use, vandalism, chemical, freeze damage, extreme weather or act of God, rust,
oxidation, stains, glass breakage, packaging and transportation fees for return. Normal
discoloration and build-up of snow are not covered either.
Seller :
For each part request, please contact our customer service. lt will need a description of problem,
pictures and consumer invoice copy. Be aware full item code must appear on invoice to give
fabricating period, color and right identification of part requested. This will ensure all proper
information to proceed the request. Moreover, name of person in charge of the request must be
written, name and address of seller ( branch ), e-mail address, fax and phone number.
2

Z
AF
Yo
c
AI AS
eY J
Jtl o
JATM
ä
N
Ñ=AT
ÞF
lo l* ,òAU
v
AT
å
á
I
€
Ez
), =:==Et
+l¡
Fr
A
gF
[ ¡[lnv
Ðru
Bg
nv Itf I
A
Bs
Bs
lJ[lnv
3
AW
@
AY I t[[

Reminder: Before assembly, don't forget to check inside of each Post (No.A),
some parts are well packed and stored inside.
A
The first Post (No. A) +>
A
The second Post (No. A)+>
A
The ttr¡r¿ Post (No. A) +>
A
M
N
o
U
V
2pcs
2pcs
1 pcs
4pcs
2pcs
o
AG
AR
AS
2pcs
2pcs
4pcs
4pcs
N
T
o
2pcs
2pcs
1 pcs
L
R
S
2pcs
1 pcs
1 pcs
4
The fourth Post (No. A) +>

PARTS LIST:
NO. Description QTY Drawing
APost 4
BBase flange 4
Br Base Cap 4
cCorner supporter (Right) 4
DCorner su pporter (Left) 4
ELong crossbar 2
Er Connector 2
E, Connector 2
FLong crossbar 2
Fr Connector 4
GShort crossbar 2
HShort crossbar 2
Corner connector 4
5

NO. Description QTY Drawing
JCorner roof tube 4
KRoof connector 1
LRoof support profile 2
MRoof support profile 2
NMiddle roof tube 4
oMiddle roof tube 2
PMiddle connector 1
oUpper roof supporting bar 2
RUpper roof support tube 1
SUpper roof support tube 1
TUpper roof support tube 2
UMiddle roof support tube 4
VMiddle roof support tube 2
6

NO. Description QTY Drawing
WMiddle roof support tube 2
XMiddle roof support tube 2
YAir vent corner connector 4
zRoof cap 1
AB Air vent panel 2
AC Air vent panel 2
AD Air vent panel 2
AE Air vent panel 2
AF Air vent profile 2
AG Air vent profile 2
AH Right roof panel for 14' side 2
AI Right roof panel for 14' side 2
AJ Middle roof panel for 14' side 2
7

NO. Description QTY Drawing
AK Left roof panel for 14' side 2
AL Left roof panel for 14' side 2
AM Right roof panel for 10' side 2
AN Right roof panel for 10' side 2
AO Middle roof panel for 10' side 2
AP Left roof panel for 10' side 2
AQ Left roof panel for 10' side 2
AR Eave profile 4
AS Eave profile 4
AT Corner moulding 4
AU Center moulding 4
AV Mosquito Net 1
AW Air vent Mosquito net 1
8

NO. Description QTY Drawing
AX Self tapping screw 24
AY Stake 16
Hardware Kit:
AA Bolt M6 X 15mm 165 Þ
BB Bolt MO X 30mm 16 Ð^**
cc Bolt M6 X 42mm 30
DD Plastic washer 16
EE Stainless washer 30
FF Allen key 1
GG Allen key 1J
o

AX4
Bx4 Bt *4
A
A
AA
I
I
I
I
I
I
I
I
AA
Br
B
e@
Step 1:
lnsert base cap (Br) into the bottom of the post (A), then using bolts (AA) secure base flange (B) on the bottom of
post (A). Repeat the step for all rest posts. Bolts can be tight completely.
l0

EX2E1X2
Fx2 F1X2
These two holes must face the ground
0000
0000
Et
EF1+F
1
EF
E
@o,@ @'l
oo
L
ooF
åâå
EF
Step 2:
lnsert the connectors (E1 & F1) into long crossbar (E) and long crossbar (F) and secure with bolts (AA). Do not
tight bolts completely yet.
Repeat this step for remaining connectors (E1 & F1) and long crossbars (E & F). This is important to align
bottom holes of connectors (F1) with bottom holes of long crossbars (E & F). This care refer to a further
step.
11

Gx2 E, X2
Hx2Ft x2
These two holes must the ground.
0000
0000
GE" H
Fr
Attention!!
Extra holes for short crossbar only.
G
1
H
E"
@@oE
Ioo0Fr
-i
-+-_
å
t..'
I ,'
| -.
-t
å
åååe
AA \(D/
GH
Step 3:
lnsert the connectors (E2 & F1) into a short crossbars (G) and a short crossbar (H) and secure with bolts (AA).
Do not tight bolts completely yet.
Repeat this step for remaining connectors (E2 & F1) and short crossbars (G & H). This is important to align
connectors threaded holes with short crossbars (G & H) holes. This care must either be taken to align (Fl)
connectors bottom holes to (G & H) short crossbarc bottom holes. ln both cases, this care is important
and refer to a further step.
12

A
E
oØ
ØøA
\
0
A0
AF
Step 4:
Secure long crossbars set (E & F) on two posts (A) by using bolts (AA).
Note fixing is done on both side of crossbars. Do not tight bolts completely yet.
Repeat on the opposite side.
Note : For your security, you may need two people for this step
13

F\., \
G
F
\ A/A GA
A
Ø
Ø
AA
A
A
Step 5:
Secure short crossbars set (G & H) on posts (A) by using bolts (AA). Note fixing is done
on both side of crossbars (G & H). Repeat for the opposite side.
Note:Please check above fig. carefully and make sure all the parts are in right position.
For your security, you may need 4 people for this step.
Do not tight bolts completely yet.
14

cx4
Dx4
Ø
A
c
", AA
G
ØØ
Ec
c
Step 6:
Secure left and right corner supporters (D & C) to posts (A) by using bolts (AA) as fig.1. Do not tight bolts yet.
Then secure other end of corner supporters (D & C) to short and long assembly crossbars (EFGH) by using bolts
(AA) as fig.2. Tightening must be done only once all bolts are located. Tight all loose bolts but following this
sequence: external of corners, inside of corners, lower end of corner supporter then upper end. Prior tightening
crossbars, ensure assembly is fully aligned.
15

x4
JX4
J
r
J
J
I
Step 7:
lnsert bolt (AA) through corner connector (l), secure with the end section of corner roof tube (J), as shown in fig.1
Repeat this step for remaining corner roof tubes (J).
16

KX1
AA AA
JK
J
I
F
E
F
Ø
Step 8:
Secure corner roof tube (J) to roof connector (K) using bolts (M). Do not tight bolts completely yet. Lay down the
corner roof tube set (J) on crossbars four corners and secure by using bolts (AA). Tight corner bolts but not full.
17

PX1
J
P
O
AA
Step 9:
Secure middle connector (P) on the corner roof tube set (J) by using bolts (AA) as shown. Tight bolts.
18

Zx1
t
J
AA AA
Step 10:
lnsert bolts (AA) through middle connector (P), and secure with roof cap (Z) as shown. Tight bolts.
19
1