Corriveau Ganyon B101205 Datasheet

Ganyon Gazebo 10'X 12'
Assembly lnstructions
8101 205-

Warning
1. lt is the consumer's responsibility to comply with any building codes, ordinances, zoning
limitations, or local homeowner's restrictions and obtain any required permit, before purchase
and installation of the products.
2. Two persons are required for assembly. The tools required includes an Allen key (part FF in
hardware kit instruction), step-ladder and other safety items such as gloves, safety goggles
and hardhat. To avoid injury from exposed sharp edges, it may be necessary to use the
above safety equipment.
3. This unit willtake at least 5 hours to set up. You must schedule enough time to complete the
assembly so you should not leave it unattended if not fully assembled, even if bolted to the
ground.
. Make sure that all components are in the box. Read instructions carefully before starting the
assembly.
. Follow all instructions to assure the strength of the shelter.
. In order to avoid damage to the shelter and its components, use appropriate tools. Do not use
the structure as a support, a step-ladder is recommended.
. Check all screws on a regular basis to maintain the solidity of the structure.
. Keep instructions and parts list for future use.
4. The screws to anchor on wood deck and concrete patio are not included.
Gare instructions
. Treat aluminum frame periodically with liquid wax for maximum protection against UV rays and
moisture.
. Mosquito nettings clean with a soft brush and lukewarm water, rinse thoroughly. Dry completely.
. Do not wash nettings with soap as it may remove the protective coating added by the factory.
Attention
. When used in winter, You need to promptly swept snow from the roof
. The mosquito nets must be removed for winter storage.
1

AC@ RË"
Þ
N
-1- AAJ
-AN
AF o
å
AOE
Mé
å.
.¿ A
AD èAEt
€MAI e
Eì €4
AE
A
B
.B
JAQ
AR=
AO
\/
{4.
{4.
tttt e.C
tlttns
2
AT
@
rtu
tltt

PARTS LIST:
NO. Description Q'TY Drawing
APost 4
BBase cap 4
CBase flange 4
DShort crossbar 2
EShort crossbar 2
FLong crossbar 2
GLong crossbar 2
HMain Connector 2
Connector 2
JConnector 4
KCorner supporter (Left) 4
LCorner supporter (Right) 4
MTip connector 10
3

NO. Description Q'TY Drawing
NRoof connector 1
oCorner roof tube 4
PMiddle roof tube 2
oMiddle roof tube 4
RAir vent tube 4
SRoof cap 1
TUpper roof panel (Middle) 2
ULower roof panel (Middle) 2
VUpper roof panel (Right) 4
WUpper roof panel (Left) 4
XLower roof panel (Right) 4
YLower roof panel (Left) 4
ZAir vent panel 2
4

NO. Description Q'ÏY Drawing
AB Air vent panel 2
AC Air vent corner connector 4
AD Middle connector 12
AE Corner connector I
AF Upper roof supporting bar 8
AG Upper roof supporting bar 2
AH Lower roof supporting bar 2
AI Lower roof supporting bar 8
AJ Roof support profile (Right) 4
AK Roof support profile (Left) 4
AL Roof support profile (Middle) 2
AM Roof support Bar (Center) 2
AN Roof support Bar (Center) 1
5

NO. Description Q'TY Drawing
AO Eave profile 4
AP Eave profile 4
AQ Corner moulding 4
AR Center moulding 4
AS Stake 16
AT Mosquito Net 1
AU Plastic plug 24 Þ
Hardware Kit:
AA Bolt M6 X 1Smm 226 0D
BB Bolt M6 X 25mm 20 @
CC Bolt M6 X 40mm 30 Ð-.**t
DD Plastic cap 16 @
EE Washer 4-
FF Allen key 2J
6

A
c
x4
x4 Bx4
A
A
I
I
I
I
I
I
Il\\
ÐD I@\\II
I
I
I
I
I
I
AA AA
BII
c/
,/
/
\-'
v--
lÚ) 1
-\
c
Step 1:
lnsert Base Cap (B) into the bottom of the Post (A), then using Bolts (AA) secure Base flange (C) on the bottom
of Post (A). Repeat the step for all rest posts.
7

D
E
H
x2
x2
x2 Jx2
(t HE
D
J
o
Ep
Do Iq
\IIII
IIo
IoI
t\ HHìIH
ä\I
\
àH
HH AA
Step 2:
lnsert the Connectors (H & J) into Short crossbar (E) and Short crossbar (D) and secure with Bolts (AA).
Repeat this step for remaining connectors (H & J) and short crossbars (D & E).
I

F
G
x2
x2
x2 Jx2
rJ)
G
J
__-_{J:i----\\\\
//- ---
/'\
F
Ge p
q
/6
\I
"\ Ia
\\ HI
å
II\
à
I
I
åAA
ä
Step 3:
lnsert the Connectors (l & J) into Long crossbar (G) and Long crossbar (F) and secure with bolts (AA).
Repeat this step for remaining connectors (l & J) and long crossbars (G & F).
9

Fú)
G
1\
\
---- -----_ A
PÌr
(1)
\-.'\\\
AG&F
Iì
fu.--- o
I
AA I
I
o
A
Step 4:
Secure Long crossbars set (G & F) on the Post (A) by using bolts (AA). Repeat on the opposite side.
Notes: For the sake of safety, you may need 2 people for this step.
o-
o/

D&E
I\
I
I
\
o-
o- AA I
I
\
A
F¡)
GD
E
1\ \E
G1\
DF\
ú) A
AA
A
Step 5:
Secure Short crossbars set (D & E) on Posts (A) by using bolts (AA). Repeat for the opposite side.
Notes: Please check above fig. carefully and make sure all the parts in right position. For the sake of safety, you
may need 4 people for this step.
11

K
L
x4
x4
A
I
I\I
I
I
\
I
Bts
I
€
€e
oê-
eBB/
\K
KA
\1\(2;
(_Ð FD
GQ)
rJj F
KLO
(3-) -,,-3]
AA
I
I
IK\
AL
PD I
\rDó
Step 6:
Secure Left & Right corner support (K & L) to Posts (A) by using bolts (BB) as fig 1. Do not tight bolts yet. Then
secure other end of corner support (K & L) to short and long assembly crossbars (DEGF) by using bolts (AA) as
fig. 2. Tightening must be done only once all bolts are located.Then, install plastic caps (DD) as fig (3) shown.
Q)
12

P
o
x2
x4
AD x12 MX6
ADS O
AD O
€Q)
M
1\
\<
(z:
't -'
I
I
I
II\\\
\\\I
I
I
I
I
I
a\ìI
I
I
I
I
I
I
I
I
I
I
ì
QI
IM
AD A
\\
AA
AA
Step 7:
Secure Middle connector (AD) 2pcs on the Middle roof tube (P) by using bolts (AA) align the part in position as
fig.'1 shown. Then insert bolt (AA) through Tip connector (M), secure with the end section of Middle roof tube (P)
as fig.2 shown.
Repeat for remaining Middle roof tube (P) and rest of 4 Middle roof tube (Q).
13
O
q
O

NX1
Too-l
I
INQ\r\I
I
II
-I
Lof,1- 1J
--------'
1\
ú) \
N
oo
o
o
M
Step 8:
Secure assembled Middle roof tube (Q) on the Roof connector (N) by using bolts (AA) as shown.
14

o
/.@\
/'v
AAY 9AA
M
\1) I\
\I
I
F&G
MMF
G
F(t \
Step 9:
Secure step I assembled parts on the Long Crossbars (F & G) by using bolts (AA) as shown.
ú) ú) M
15

9t
'aprs oilsoddo Jol leodau
'u/r^or.ls Z'6U se (¿) eqnl loor olpply\l r.{tr/Ì^ per1oege '(¡) ¡es ro}cêuuoc ¡oo¡ qônolq¡ (yy) s¡oq yesu¡
uoql 'umorls ¡'69 se (W) sloq 6ursn Áq (C t =) sreqssor3 ôuo1 aq¡ uo (¿) eqn¡ toor olppl4 potquosse orncos
:0 L dols
3
,)
\d
d
\Z, \
\z\
fWE
Y
c
II
I
I
I
I
II\\
II
\I\
Id
WÆS IN
\
WI\/
\/\/\,/
\--\/
--J 7 \_---
\tvt,
a--'
d
--
I
I
I
l¿
-r
l+ +
I
I
I
I
LoJ

o
R
x4M x4
X4 AE X8
AA ----í:)_
q
AA
&'-
\R
ì
I
I
I
I
I
III
òR
o/
/
/
-
¿
¿(t \
(3-) AE
o
(q-;
2\
M\
o
I,Zì
I
I
I
I\\
oIq
I\ì
I
I
I
I
a\II
I
I
I
\AE
M
AA
---------
Step 11:
Secure Air vent tube (R) on the Corner roof tube (O) by using bolts (AA) as fig.1 shown. Then insert bolt (AA)
through Tip connector (M), secure with the end section of Corner roof tube (O) as fig.2 shown. Finally, secure
Corner connector (AE) 2pcs on the Corner roof tube (O) by using bolts (AA) align the parts in position as fig.3
shown.
Repeat for remaining Corner roof tubes (O).
17

SX1
g'BF
-( EE EE
\3\I
\r-
II
I
I
I
I
I
RSo
\,g
AAr- AA
9
N\\II
I
I
I
I
II
I
¿
I\
t
H\
AA (s--) ,
\--------/ R R o
N\
o
ú) M
G1\
F\
Step 12:
1. Secure Corner roof tubes (O) on the four corners of Crossbars by using bolts (AA) as fig.1 shown. Do not
tighten the bolts. lnseft bolts (AA) through Roof connector set (N), secure with Corner roof tubes (O) as fig. 2
shown. Tighten all bolts now.
Repeat for remaining Corner roof tubes (O).
2. lnsert bolts (BB) and washers (EE) through Roof cap (S), secure with Corner roof tubes (O) as fig.3 shown
o
1
18

ZX2 AC x4
AB X2 AUÞ XB
t- -l
R
I
IR
t- {J-,' JAC I
I
I
I
Io
t- -l AA
I
IRí-t-l
'-' z
(à
AC RR
t- 1ù --)
Step 13
lnsert Air vent panel (Z) into Air vent tube (R) as fig. 1 shown and secure with Plastic plug (AU) as fig. 2 shown.
Then insert adjacent Air vent panel (AB) into Air vent tube (R) as fig. 1 shown and secure with Plastic plug (AU)
as fig. 2 shown, hold in position. Finally insert bolt (AA) through Air vent corner connector (AC), secure with Air
vent tube (R) as fig. 3 shown.
Notes: lnstall clockwise to prevent the panels slide off. 19