Corriveau Morelia B101215 Datasheet

Morelia Gazebo 10'X 12'(2016)
Assembly lnstructions
E¡101 21 5-

Security rules
Warning :
Keep away flame or heat source from gazebo fabrics. Othen¡rise fabrics can burn or melt and can
cause severe burn on nearby persons. ln this case, material damage has to be considered.
Moreover, the adding of any substance will block or severly slow down capacity of fabric to resist
or be flame retardant.
Regulation
It is the responsability of consumer being in accordance with city regulation, construction code,
zoning or any limitations and obtaining permit prior erecting the gazebo.
Recommendation
Prior to proceed to erect the gazebo, a check-up of quantity of each items should be done. Some
parts may have sharp edges, wearing gloves is recommended.
Figure at least five hours to complete the set-up with two persons. Consider having enough time
for completlon of erecting. Even well anchored, a non complete gazebo unit can get or create
damage to nearby environment.
Keep away from any electric installation or transportation device.
A check up of tightening of all bolts should be done all across lifespan of gazebo.
Even if this gazebo is built for year round use, this is strongly recommended to remove snow from
top.
Mosquito net and curtains (optional) must be removed from the unit at freezing period.
lnstruction manual must be read prior start-up of erecting.
All recommendation must be followed carefully to ensure perfect sturdiness of the unlt.
Use proper tools and equipements for a safe and compliant installation. Never climb, sit or stand
on structure while erecting.
Anchoring bolts or other anchoring devices are not supplied.
Always recommended to keep instruction manual for further reference.
1

Gare
Never use a high pressure washer. Use of mild soap in a lukewarm water is the best solution for
frame only. A clear water rinse is necessary then. Never use soap for fabrics, this will reduce
their capacity and consequently their lifespan and general look. For fabrlcs, a soft brush and a
lukewarm water is offering an excellent cleaning.
Warranty
Govered
This gazebo is warranty from any manufacturing defect for one year at normal use. This limited
warranty is for one year for parts only.
ln any case a part is needed, please contact the seller giving description and pictures of defect.
Not covered
All damage caused by commercial use, improper care, neglected storage, unreasonable or
abusive use, vandalism, chemical, freeze damage, extreme weather or act of God, rust,
oxidation, stains, glass breakage, packaging and transportation fees for return. Normal
discoloration and build-up of snow are not covered either.
Seller :
For each part request, please contact our customer service. lt will need a description of problem,
pictures and consumer invoice copy. Be aware full item code must appear on invoice to give
fabricating period, color and right identification of part requested. This will ensure all proper
information to proceed the request. Moreover, name of person in charge of the request must be
written, name and address of seller ( branch ), e-mail address, fax and phone number.
2

V
o
AC
AB
t I ttnr'¡
KAJ
t
Br
tlftnn¡
t I ttnr'¡
AJ
IAG
/.
\
Kr L
AK
I
Kr
AF
DAK¡
AKr
ß
Á
t t ttnr'¡
3

PARTS LIST:
NO. Description QTY Drawing
APost 4
BBase flange 4
Br Base cap 4
cCorner supporter
(Risht) 4
4
DCorner supporter (Left)
ECrossbar 2
2FCrossbar
GSide Panel (Left) 1
HSide Panel (Left) 1
Side Panel (Right) 1
JSide Panel (Right) 1
2KConnector
Kr Strengthen connector 2ooo o
o ooo
4

NO. Description QTY Drawing
LConnector 2
MRoof Crossbar 1
NRoof Crossbar 1
oM¡ddle roof tube 1
PMiddle roof tube 1
oSide roof tube 2
RSide roof tube 2
SSupport frame 4
TRoof support tube 3
URoof support tube 3
VRoof cap 1
WRoof cap 1
XRoof panel 4
5

QTY Drawing
NO. Description
Y Upper roof panel 4 t-
t-
zLower roof panel 4
1
AB Roof profile (Left)
AC Roof profile (Right) 1
AD Upper roof profile
(Left) 1
1
AE Upper roof profile
(Risht)
AF Lower roof profile
(Left) 1
AG Lower roof profile
(Risht) 1
3
AH Eave profile
3
AI Eave profile
AJ Bracket (Left) 4
AK Bracket (Right) 4
AL Mosquito net 1
16
AM Stake
6

Hardware Kit:
NO. Description QTY Drawing
AA Bolt MO X 15mm 1 1
30D
BB Bolt M6 X 25mm 8Ð.---
cc Bolt M6 X 30mm 39
DD Bolt M6 X 45mm 44
EE Bolt MO X 65mm 4
FF Bolt M6 X 75mm 3
GG Nut 25 @
HH Bolt cap 25
il Plastic washer 46 O
JJ Stainless washer 31
KK Plastic cap 16
LL Allen kerr
MM Spanner 1
NN Bolt M6 X 35mm 6
7

X4
A
BX
X4
4Br
AA
I
I
I
I
I
I
I
I
I
Iìì
AA AA
B
Br
/-ì\,
Step 1.
lnsert base cap (81 ) intothe bottom of the post (A ), then using bolts (AA)secure baseflange (B )on the bottom
of post ( A ). Repeat the step for all rest posts. Bolts can be tight completely.
.-
\ t/
I

oo
ooo
oo
X2
E
F
XX
22
K
x2
Kt
OF
+K<-
'l
Attention!!
Do not put bolts in middle holes, this care refer to a further step.
l-
E
¡Kt
ååå
o o 0
oo
ap
II
1
J
o
o
-o
-,--o
'O
o
lnserttheconnector(K)intocrossbar(E)andcrossbar(F),Thisisimportanttoalignconnectorthreaded
holeswithcrossbars(E&F)holesandmustalsobedonetoalignstrengthenconnector(Kl)holeswith
crossbars holes.
Then insert bolts (AA )through strengthen connector ( K1 ), secure with the crossbars holes. Do not put bolts in
middle holes, this care refer to a further step. Bolts can be tight completely. See figure shown.
9
tr /F
Kr
Step 2.

o
o
o
o
-
t-
x
x
x
-
o
I
ii
ìl
'ç
I
ll...
I
I
I
I
!I
f
bi
I
I
o
ì
\
J
olttttør=
o r o¡ o, :'ã
lo5=Qä
õ r q9.= l
(D C ^1ll i +
=dÉ : a g i
-o=o
ö -r93
* $ +.o
5(oo
o-JR
g -ai
: ã'q;
U' C ØV
O tt€ ='
e Beá
ai - -{d
J-+
o o =.*
= =În u,
2. u a'*
g* 3 ='ç
H ott r
H to o
o o lt^
d=o
rî\ o é-
Ë E iå
= flrõ'a
)^-+
o aã ã
o I :9F
2- Ëãç
ö (rg=
E Fi:
o o_i r
1 E'ß;
lJ^-
J aoó
q äiH
..". fáã
; sÉ8.
r l¿=+
9--
= E:8
É { gq
ã iä -Þ
ô O-P
P I õ-X
: q+ö
g ö: 3 ,Ë-'
(o clo
5(D
U)
o
o
(¡)
o
-

o
o
0
o
(-
t-
x
X
-\
x
J
Lr
ti
I
I
C-
P
Lt
o-{ttttø,-
oiûrôrf;
ås aðE I
oc ^O / +
69.-. (- 5 - d
'.-É -åYe
ö -ørd=
ã E =.Þ
G i'= ä
3 ã'AÊ
Ø c i+_
e Ëna
o'=.
_ 5 -t(o
v-¿
5oao,^
6", äl: .á
o - Jõ
E .=q ä
o oi¡i^
-r--
CL ã-
c-Or^. ro3
I 3 +?
ô (cl ,='
õ ^: =
.=. -l ti e.
u
--J5o
2d ñ fl¡
o u9 d
!o--
P o¡ 31
¿r!s
o ,='o-
=Xo)
o=f
èäo
E 6=E
ç' ãñ.q
Ì €=.É.
ã E:Ë
-rrv
b g9oõ'
o o L^
. ao->
ä 3¿'¿
1 ¿i'= ä
X 5r, +
,E g' t''r
=o
U)
o
Þ
À

Step 5.
Secureleftsidepanelsset(G&H)ontwoposts(A)byusingbolts(AA)and(DD).Notefixingisdoneon
both sides of side panels. Do not tight bolts completely yet.
Note : For your security, you may need two people for this step.

o
G
Step 6.
Securerightsidepanelsset(l&J)ontwoposts(A)byusingbolts(AA)and(DD).Notefixingisdoneonboth
sides of side panels. Do not tight bolts completely yet.
Note : For your security, you may need two people for this step.

HE
A
A
A
Ø
\
Fo
A
I
I
I
oo-_ F
Step 7.
Securecrossbarsset(E&F)onposts(A)byusingbolts(AA)and(DD).Notefixingisdoneonbothside
of crossbars ( E & F ). Repeat for the opposite side.
Note : Please check above fig. carefully and make sure all the parts are in right position. For your security,
you may need 4 people for this step.
Do not tight bolts completely yet.
14

x4
C
X4
D
Ø
E
A
A
@.
KK erc rr
KK
I
I
I
I
D
AA¡
O
AA
A
Step 8.
Secureleftandrightcornersupporters(D&C)toposts(A)byusingbolts(AA)asfig.l.Donottightboltsyet.
Thensecureotherendofcornersupporters(D&C)toassemblycrossbars(GFEH)byusingbolts(AA)asfig.2.
Tightening must be done only once all bolts are located. Tight all loose bolts but following this sequence : external
of corners, inside of corners, lower end of corner supporter then upper end. Prior tightening crossbars, side panels,
ensure assembly is fully aligned.
Finally install plastic caps ( KK ) as fig. 3 shown. 15

X1
M
X1
N
M
N
-
--),+
Attention !
Do not put bolt in this hole, this o
care refer to a further step M
N@
JJ HH
)
L
GG
i6)tÐo
iEE o
JJ &'
-&,
JJ
o
o
M
N
Step 9.
lnsertroofcrossbar(N)intoroofcrossbar(M),Thisisimportanttoalign(N)roofcrossbarholeswith(M)
roof crossbar holes. Then insertbolts (EE )and stainlesswashers (JJ )through roof crossbars ( N & M ), secure
with the use of stainless washers ( JJ ) and nuts ( GG ). Finally install bolt caps ( HH ). One hole do not have bolt in,
this care refer to a further step. See figure shown. Bolts can be tight completely.
16

1
J
o
Step 10.
Secureroofcrossbarsset(N&M)onthesidepanels(GHIJ)byusingbolts(DD)andstainlesswashers(JJ).
Note : Please check above fig. carefully and make sure all the parts are in right position. Two people are
required for this step.
Do not tight bolts completely yet.
17

l.Securemiddlerooftube(P)ontheroofcrossbars(M&N)byusingbolts(EE)andnuts(GG),Theninstall
boltcaps(HH)asfig.1 shown.Finallysecuretothecrossbars(E&F)usingbolts(AA)asfig.3shown.Donot
tight bolts completely yet.
2.securemiddlerooftube(O)ontheroofcrossbars(M&N)byusingbolts(DD)andstainlesswashers(JJ)as
fig.2shown.Thensecuretothecrossbars(E&F)usingbolts(AA)asfig.3shown.Donottightboltscompletely
yet.
Step 11

o
R
X2
x2
I
AA
I
R
Step 12.
l.Secure side roof tube (R )on the roof crossbars (M & N )by using bolts ( AA )asfig.1 shown. Then secure to
thecrossbars(E&F)usingbolts(AA)asfig.3shown.Donottightboltscompletelyyet.
2.Securemiddlerooftube(Q)ontheroofcrossbars(M&N)byusingbolts(DD)andstainlesswashers(JJ)as
fig.2shown.Thensecuretothecrossbars(E&F)usingbolts(AA)asfig.3shown.Donottightboltscompletely
yet.