Corriveau lndia B121202 Datasheet

lndia gazebo 12x 12' (201 8)
BL2L202 model
Assem bly Instructions
P1

0
4y 17
æ,12
15
Å
16
-:=:
1
J-L
8&
{tb
ñ
:==æ 4û
113
24 25En
7
ú
14
u
ül
ú
I3a
4T
,\
6
-
131
3Jrr2
-
P2

READ & SAVE THESE INSTRUCTIONS:
Please read instructions carefully and identify all parts
before assembly.
. Caution: Small parts, Iike plastic caps, may pose a chokinghazard
to young children. Keep out of reach of small children.
. You may require 2-4 persons to do the assembly.
. Do not leave outside during winter. Remove the top during bad
weather.
. Fasten the base to the deck either wood, concrete or others.
. Do not tighten all parts before the assembly is completed.
PART LIST:
NO, FIGURE DESCRIPTION Q'TY
1Post 4
2sb Base Flange 4
3Crossbor 4
4Crossbor 4
5lnner Connector 4
6ICenter Connector 4
7üCorner moulding 4
Ilnside connector 4
ICorner Tip Connector 4
10 Short Roof Pole 4
11 Long Roof Pole 4
12 Roof Connector 1
13 Bottom Supporting Tube 4
14 Bottom Supporting Tube 4
15 æUpper Supporting Tube 4
P3

16
-
Upper Supporting Tube 4
17 Roof Cap 1
18 Roof Panel I
19 Roof Panel I
20
-rr--r
Center Supporting Profile 4
21 Center Supporting Profile 4
22 Eave Profile 4
23 --- Eave Profile 4
24 sEave Connector 4
25 \o Eave Connector 4
26 rScrew M6 X 15mm 109
27 rSquare HD Bolt M6 x L5 mm 24
28 ûn Screw M6 X 25mm 16
29 GreÞ Screw M6 X 35mm 16
30 @Nut M6 24
31 ffi Mosquito Net 1
32 Corner support 4
33 Corner support 4
34 CI Plastic Cap 16
35 Stake 12
36 JAllen Wrench 1
37 Spanner 1
P4

Step 1:
Secure base flange (2) on the bottom of post (1) by using screws (26) .Repeat
the step for remaining posts.
1
2
1
2
1
1
P5

Step 2:
1. lnsert Inner connector (5) into crossbar (3) and crossbar (4), and secure with
screws(26). Then insert screws (26) trough inside connector (8) and secure at
upper center ofcrossbar (3) and crossbar (4).
Notes: Inner connector (5) C shape must face outward when installation.
2. Secure center connector (6) on crossbar set (3 & a) by using Screws (26)
Repeat for remaining 3 Crossbar sets.
34
4
3
4
3
P6

2
Step 3:
1. Secure crossbars (3) and crossbars (4) on posts (1) by using screws (26) as
figure (1)shown, do not tighten the screws. Then secure crossbars (3) and
crossbars (4) on posts (1)by using screws (29) as figure (2) shown. Tighten all
screws.
Notes: For the sake of safety, you may need 4 people for this step.
2. Fix corner moulding (7) at corner section of crossbars set (3 & a) by
using screws(26) as figure (3) shown
7u
4
3
4
1
7
4
33
3
tt
\
1
1
1
7
c
4
29
4
29 I
7
E)
P7

Step 4.
Secure corner supports (32 & 33) on posts (1) by using screws (28) Do not tighten
the screws. Then secure other end of corner supports (32 & 33) on the crossbars
set by using screws (26) as figure (2) shown. Tighten all the screws.
Cover screws (28) with plastic caps (34) as fig.1 shown.
334
3
4
3
33 3
32
1
1
1
1
26
L
'r
34 28
34
P8

Step 5:
1 . lnsert two square head bolts (27) through short roof tube (10) for coming step (7).
Then insert square head bolt (27) at end of short roof tube (10) and secure with roof
connector (12), tighten with nu (30) as figure (1 &2) shown.
2. lnsert screw (26) through tip connector (8) already secured in step 2 and secure
short rooftube (10) as figure (3) shown.
Repeat for remaining 3 sides. FIG 1
10
2
10 10
FI
P9

Step 6:
1. lnsert screw (26) through corner tip connector (9) and secure with long roof tube
(1 1) asflgure (1) shown.
2. Insert two square head bolts (27) through long roof tube (1 1) for coming step 7 as
shown.lnsert square head bolt (27) at end of long roof tube (11) and secure with
roof connector (12),tighten with nut (30) as figure (2 & 3) shown.
3. Secure corner tip connector (9) on the corner section of crossbar sets by using
screws (26) as figure (4) shown.
Repeat for remaining 3 corners.
11
11
2
2
11
12
1
27
f
11
611
P10

Step 7:
1. Secure roof cap (17) on roof connector (12\ by using screws (26) as figure (1)
shown
2. Overlap bottom support tube (13) and bottom support tube (14) through square
head bolts (27),tighten with nuts (30) as figure (2) shown.
Notes: Hex Bolts have been installed at steps 5 & 6.
3. Overlap upper support tubes (15) and upper support tubes (16) through square
head bolts (27), tighten with nuts (30) as figure (3) shown.
Notes: Hex Bolt have been installed at steps 5 & 6.
11
11
FI 2
13
27
14
0
P11

Step 8:
1. Remove protective films from roof panel (18) and insert into long roof tube (1 1)
and short roof tube (10) upper groove as figure (1) shown. Then insert roof
supporting profile (20) front edge in upper groove and back edge in long and short
roof tubes lower groove as figure (2) shown. Then remove protective fllms from roof
panel (19) and insert into long roof tube (1 1) and short roof tube (10) lower groove
as figure (3) shown. Remember the top edge of roof panel (19) must slide into roof
supporting profile (20) as figure (4) shown.
2. Work on the adjacent side, remove protective films from roof panel (18) and
insert into short roof tube (10) and long roof tube (1 1) upper groove. Then insert
roof supporting profile (21) front edge in upper groove and back edge in lower
groove of short and long roof tube (10 & 1 1). Then remove protective fllms from roof
panel (19) and insert into short roof tube (10) and long roof tube (1 1) lower groove.
Remember the top edge of roof panel (19) must slide into roof supporting profile (21)
Repeat step 1 & 2 for remaining 3 sides of roof installation.
Notes : Please do not let the panels slide off. 1
17
FIG 118
20 I
19
I1
F
P12

Step 9:
1 . lnsert screws (26) through eave connector (24), eave tube (22) and eave tube
(23),secure with short roof tube (10) as figure (1) shown.
2. lnsert screws (26) through eave connector (25), eave tube (22) and eave tube
(23),secure with long roof tube (11) as figure (2) shown.
Recommend to install clockwisely in order to prevent the panels slide off.
23 24
24 22
5
223
11
P13

Step 10:
1. Hang the mosquito net (31) by hooks properly.
2. Secure stakes (35) through base flange (2) into the ground. Depend of patio
surface, use proper anchoring devices. Anchors not supplied.
3. Remove all gazebo assembly stickers.
Please ensure posts and ground are perpendicular with each other once the unit is
assembled. Tighten all bolts evenly. Enjoy your leisure time with gazebo.
31
1
I
31
Ir
1
P14