CREE LIGHTING CONNECTED MAX User manual

QUICK START GUIDE
SMART TAPE LIGHT STRIP

1
What's in the box
Please consult this checklist for all parts.
Controller
6.5 Foot Tape light Power Adapter
Connector Adhesive Pads
Manual
IR Remote

2
Description
Working voltage: DC12/24V
Current: 2Ax 3CH
Max load: 12V/36W; 24V/72W
Product size: L77 x W35 x H17mm
Working environment: Indoor
Working temperature: -10°C-40°C (14°F-104°F)
Humidity: <80%RH
90°
IR Antenna
(Receives signal
from IR remote,
within a 90° radius)
On/Off
Color Change
Music/Color Rhythm
Microphone
Tape Light Connector
Power Port for Wall Plug

3
Power Connection
Step 1: Connect Tape Light Strip to Controller
Step 2: Connect Power Adapter to Controller
Step 3: Plug Power Adapter into wall outlet
The white arrow on the Controller must
align with the “+12V” text printed on the
Tape Light Strip
X
X

4
Attach your Tape Lights
Clean the surface with a
wet, damp cloth. Surface
must be dry and free of
dirt or oils.
Peal off the backing
strip from the
adhesive.
Place the Tape
Light Strip where
you want, and
gently press down
to adhere.
Do NOT bend Tape
Light Strip at LED or
connection when going
around corners.
Do NOT bend at more
than a 90° angle.
Connect the Tape
Light Strip into the
Controller and Wall
Plug. Use the supplied
Adhesive Pad to
secure the conroller.
3
12
4
<90°
LED
5

Cut to adjust length
at the connector
sections.
Insert trimmed ends of Tape Light Strip
into the supplied Connector.
Important!
Match the “+12V” text printed on the
Tape Light Strip to the “+” sign on the
Connector. Close hinged Connector
securely.
Repeat for the other end. Use the
supplied Adhesive Pads to secure the
Connector to the mounting area.
Link up to 32 feet with the Cree Lighting
Connected Max Tape Light Extension Kit.
1
2
“+12V” to “+”
5
Trim Tape Lights / Connect Two Tape Light Strips
Trim Tape Light Strip
Connect two Tape Light Strips

6
Tape Light Strip Control
Adjust with Controller
Adjust with IR Remote
Click On / Off
Static / Dynamic mode
Music / Color Rhythm
Point the IR Remote at the
IR Antenna to control.
Adjust with App
See page 7 to pair Smart Tape
Light Strip with Cree Connected
Max App
Static /
Dynamic
Mode
Night
Light
Color
Changing
Music /
Color
Rhythm
On / Off
Brightness
Changing
Mode
Changing
CCT
Changing
Turn Off
60s Later

7
Pairing with the App
Download
The Connected Max Smart Tape Light Strip must pair to a 2.4GHz Wi-Fi network.
Once paired, you can control on any Wi-Fi or cellular network. For most users,
pairing will be quick and simple. But depending on the type of wireless router
you have, you may need a little more information to get started. Refer to our
Wireless Router Guide at creelighting.com/connectedmax for more
information.
NOTE: If you need to re-select the Wi-Fi network, please press and hold the
"Power" button on the Controller for 5 seconds, the device will restart, and the
Tape Light Strip will slowly flash.
Pairing to your network
Download App (Android)
Download App (iOS)
Please keep network available
2.4GHz 5GHz
The Cree Lighting App is available for both iOS and Android.
Search Cree Lighting in the App store or Google Play to download the app.

8
How to pair your Tape Light Strip
Pairing with the App
Download the Cree Lighting app and register your account. Open the Cree
Lighting App, click "Sign Up", read the "User Agreement Privacy Policy"
and click "Agree."
Plug the Cree Lighting Connected Max Smart Tape Light Strip you want to pair
into a wall outlet and press the power button. The Tape Light Strip should start
slowly flashing to indicate pairing mode. If the Tape Light Strip is not slowly
flashing, it may need to be reset.
Reset a Tape Light Strip by holding down the Power button on the Controller
for 5 seconds.

In the Cree lighting app, tap the “+ ”
sign in the upper right-hand corner
of the Home screen.
The Tape Light Strip you are pairing
will appear on screen, tap “Next.”
The Wi-Fi network your phone is
connected to will appear. You can
change your network to a 2.4 GHz
network if needed and enter
password.
The Cree Lighting app will add your
Tape Light Strip.
6
Pairing with the App
9
1 2

34
In the Cree lighting app, tap the “+ ”
sign in the upper right-hand corner
of the Home screen.
The Tape Light Strip you are pairing
will appear on screen, tap “Next.”
The Wi-Fi network your phone is
connected to will appear. You can
change your network to a 2.4 GHz
network if needed and enter
password.
The Cree Lighting app will add your
Tape Light Strip.
Pairing with the App
10

Pairing with the App
Once added, you can rename
your Tape Light Strip by tapping
the pencil icon next to the name
– then click “Done.”
5
11
CERTIFIED TO UL STD153
CERTIFIED TO CSA STD C22.2#250.4
Only connect to adjacent units
Tout est connecté aux unités adjacentes
Intended adapter for strip: ASLP67W-240090
adaptateur de bandes destinées: ASLP67W-240090
SUITABLE FOR DAMP LOCATIONS
CONVIENT AUX EMPLACEMENTS HUMIDES
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 40°C
PEUT ÊTRE UTILISÉ À UNE TEMPÉRATURE AMBIANTE N'EXCÉDANT PAS 40°C
Safety Information

Changes or modifications not expressly approved could void your authority to use this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment
and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and
operated in accordance with provided instructions and the antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter. End-users and
installers must be provided with antenna installation instructions and consider removing the
no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
12
Safety Information
IMPORTANT PRODUCT INFORMATION
SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT
IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
This device is not intended for underwater use. To protect against electric shock, do not
intentionally submerge or immerse your device, battery, or adapter in water or expose your device
or adapter to other liquids. Do not spill any food or beverages on your device, battery or adapter.
Do not attempt to clean or polish your device, battery, or adapter with or expose your device,
battery, or adapter to oil, lotion, or other abrasive substances. Don’t expose your device, battery,
or adapter to salt water or other conductive liquids. Do not expose your device, battery, or adapter
to pressurized water, high velocity water, or extremely humid conditions (such as a steam room).
If your device, battery, or adapter gets wet, carefully unplug all cables without getting your hands
wet and wait for it to dry completely before plugging it in again. Do not attempt to dry your device,
battery, or adapter with an external heat source, such as a microwave oven, or hair dryer. To avoid
risk of electric shock do not touch your device, battery, or adapter to any wires connected to your
device during a lightning storm while your device, battery, or adapter is plugged in. If your device,
battery, or adapter appears to be damaged, discontinue use immediately.
Use only accessories supplied with your device or specifically marketed for use with your device, to
power your device. Use of third-party accessories may impact your device’s performance. Read all
safety instructions for any accessories before using with your device.
CAUTIONS & WARNINGS: Not suitable for use with standard dimmer switches. Not intended for
use with emergency exit fixtures or emergency lighting. Risk of electric shock or burns. Turn power
off and let cool before inspection or replacement. Do not open – no user serviceable parts inside.
Use only on 120 volt AC circuits. Do not use if outer shell is cracked, broken or missing, even if
lamp continues to light. Suitable for use in operating environments not exceeding+40°C (+104°F).
Indoor/Outdoor – suitable for damp locations, but not for use where exposed to weather or water.
Suitable for use in totally enclosed and recessed fixtures.
Not compatible with 5GHz Wi-Fi networks.
Not for use with standard dimmer switches.

Changes or modifications not expressly approved could void your authority to use this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment
and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and
operated in accordance with provided instructions and the antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter. End-users and
installers must be provided with antenna installation instructions and consider removing the
no-collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Safety Information
13
IMPORTANT PRODUCT INFORMATION
SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT
IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
This device is not intended for underwater use. To protect against electric shock, do not
intentionally submerge or immerse your device, battery, or adapter in water or expose your device
or adapter to other liquids. Do not spill any food or beverages on your device, battery or adapter.
Do not attempt to clean or polish your device, battery, or adapter with or expose your device,
battery, or adapter to oil, lotion, or other abrasive substances. Don’t expose your device, battery,
or adapter to salt water or other conductive liquids. Do not expose your device, battery, or adapter
to pressurized water, high velocity water, or extremely humid conditions (such as a steam room).
If your device, battery, or adapter gets wet, carefully unplug all cables without getting your hands
wet and wait for it to dry completely before plugging it in again. Do not attempt to dry your device,
battery, or adapter with an external heat source, such as a microwave oven, or hair dryer. To avoid
risk of electric shock do not touch your device, battery, or adapter to any wires connected to your
device during a lightning storm while your device, battery, or adapter is plugged in. If your device,
battery, or adapter appears to be damaged, discontinue use immediately.
Use only accessories supplied with your device or specifically marketed for use with your device, to
power your device. Use of third-party accessories may impact your device’s performance. Read all
safety instructions for any accessories before using with your device.
CAUTIONS & WARNINGS: Not suitable for use with standard dimmer switches. Not intended for
use with emergency exit fixtures or emergency lighting. Risk of electric shock or burns. Turn power
off and let cool before inspection or replacement. Do not open – no user serviceable parts inside.
Use only on 120 volt AC circuits. Do not use if outer shell is cracked, broken or missing, even if
lamp continues to light. Suitable for use in operating environments not exceeding+40°C (+104°F).
Indoor/Outdoor – suitable for damp locations, but not for use where exposed to weather or water.
Suitable for use in totally enclosed and recessed fixtures.
Not compatible with 5GHz Wi-Fi networks.
Not for use with standard dimmer switches.