CREE LIGHTING VG Series User manual

VG Series
LED Parking Luminaire
Pendant Mount (PD)
1 of 2 LPN00100X0002A0_B
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
TO INSTALL:
LUMINAIRE INSTALLATION
STEP 1:
Feed luminaire leads through the
Water Shield and attach the Water
Shield to the luminaire using (4)
supplied #8 screws. See
Figure 1 and 2.
STEP 2:
Attach Pendant Mount Bracket to
customer supplied pendant kit. See
Figure 1.
STEP 3:
Feed luminaire leads thru Pendant
Mount Bracket and customer supplied
pendant kit. See
Figure 1.
STEP 4:
Position the arrow on the Pendant
Mount Bracket to point towards the
recessed area nearest to the latch on
the luminaire. See Figure 3.
STEP 5:
Attach Pendant Mount Bracket and
customer supplied pendant kit to
luminaire by engaging the clips on
the luminaire with the slots on the
Pendant Mount Bracket and rotate
until latch locks securely. See
Figure 3.
NOTE: May require extra pressure on
Pendant Mount Bracket to engage
luminaire clips into slots.
NOTE: If the Pendant Mount Bracket
slots become deformed during
installation, slightly reopen the slots
back up using a screwdriver to ensure
proper install of luminaire.
1
2
Pendant Mount
Bracket
3
Pendant Kit
(Supplied by
Customer)
Water Shield
Luminaire
Water Shield
Slots
Slots
Luminaire
Clips
Latch
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including
the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. To reduce the risk of electrical shock, turn off power supply before installation or
servicing.
DANGER – Risque de choc – Couper l’alimentation avant l’installation.
2. This luminaire must be installed in accordance with the NEC or your local electrical code.
If you are not familiar with these codes and requirements, consult a qualied electrician.
Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous
n’êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien
qualié.
3. DO NOT lift luminaire by the power leads.
4. Pendant kit is NOT supplied with luminaire.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE

2 of 2 LPN00100X0002A0_B
www.creelighting.com
© 2019 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content
is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree®and the Cree logo are
registered trademarks of Cree, Inc.
STEP 6:
Cut off any excess length of leads from the top of the
customer supplied pendant kit.
STEP 7:
Make wiring connections to customer supplied junction box
per “Electrical Connections” section.
STEP 8:
Using customer supplied hardware attach pendant kit and
luminaire to customer suppled junction box with the arrow
on the Pendant Mount Bracket directed parallel to vehicle
traffic. See Figure 5.
4
ELECTRICAL CONNECTIONS
STEP 1:
Make the following Electrical Connections :
a. For 120/277/347V connect the black fixture lead to the
voltage supply position of the junction box (Hot 1 for
208/240/480V wiring).
b. For 120/277/347V Connect the white fixture lead to the
neutral supply position of the junction box (Hot 2 for
208/240/480V wiring).
c. Connect the green or green/yellow ground lead to the green
wire position of the junction box.
d. If Dimming is an option; connect the violet dimming positive
lead to the supply dimming positive lead.
e. If Dimming is an option; connect the grey dimming negative
lead to the supply dimming negative lead.
Pendant Mount
Bracket
Arrow On Mounting Plate
Pointing Parrallel To
Traffic
5