Decon wheel MED3025 User manual

2020-08-26
Assembly instructions for Etac Sting
MED3025
1. Remove wheels and anti-tip devices on both sides. Check the correct placement for the
stop pin, see placement for the bracket. (See picture below.)
2. Assembly the E-drive bracket (right side) according to picture, here you can see two
placement opportunities.
A
A
B
B

2020-08-26
3. Parts pair mountingset:
Item No. Part Number Qty Description
1 HW069 1 Hubsleever
2 BR1100-03 2 Spacer
3 MED 2004 1 Bracket
4 100 400 017 1 Spacer
5 280008 2 Spacer
6 XSM8X40 1 Screw M8 x 40 Rounded head
7 XSM8ML 1 Locknut M8
8 XSM16M 1 Nut M16
9 405239 1 Nordlock Washer
10 XSM8BR 1 Plain Washer M8
Item No. Part Number Qty Description
1 XSM6X65 1 Bolt M6 x 65
2 50393 1 Spacer
4. Assembly the back placed battery bag.
MED1348 or MED1348L

2020-08-26
Assembly instructions for Joystick on armrest
Details included in MED1348/MED1348L
Item No Part number Qty Description
1 XOC-48160-B0 1 Upper bracket complete
2 XSM6X30 2 Screw M6 x 30
3 XSM6BR 4 Flat washer M6
4 XSM6ML 4 Lock nut M6
5 XSM6X16 2 Screw M6 x 16
6 MED1547 3 Bracket
7 MED1501 Rev6 1 Bracket for short armrest (Only in MED1348)
MED1482 Rev2 1 Bracket for long armrest (Only in MED1348L)
Tightening torque
6Nm.
1
2
3
3
4
5
6
6
7
4

2020-08-26
MED1356
Attendant control with Joystick controller
Item No. Part Number Qty Description
1 MED1317 1 Bracket
2 XSM6X35 1 Screw M6 x 35
3 XSM6X16 2 Screw M6 x 16
4 XSM6BR 3 Plain Washer M6
5 XSM6ML 2 Locknut M6
6 MED1316 1 Plate with pin
7 XA2-2612K-00 1 Clamp with thread
8 XA2-2612E-00 1 Clamp with hole
5. Assemble the Attendant control with the Joystick control on any side. If you change
side you must move (A) to the other side.
A

2020-08-26
Alternate attendant control (Only on Right side)
Item No. Part Number Qty Description
1 XSM6TG 1 Washer
2 Xklamma2 1 Clamp
3 XSM6X20 1 Screw M6 x 20
4 XSM6BR 1 Plain Washer 6,4
5 MED1200 1 Attendant control
6. For the attendant control unit, you need these parts.

2020-08-26
Om inget annat specifiseras, använd följande åtdragningsmoment.
Unless otherwise specified, use the following tightening torque.
Metriska grovgängor, stål.
Metric coarse threads, steel.
Gänga / Thread
Åtdragningsmoment / Tightening torque
M3
1,2 Nm
M4
3 Nm
M5
6 Nm
M6
10 Nm
M8
25 Nm
M10
50 Nm
M12
85 Nm
Navhylsor.
Hubsleever.
Gänga / Thread
Åtdragningsmoment / Tightening torque
M16x1
30 Nm
M18x1
40 Nm