Deif GC-1F User manual

DEIF A/S · Frisenborgvej 33 · DK-7800 Skive · Tel.: [phone] · Fax: [phone] · [e-mail] · www.deif.com
DEIF A/S · Frisenborgvej 33 · DK-7800 Skive · Tel.: [phone] · Fax: [phone] · [e-mail] · www.deif.com
DEIF A/S · Frisenborgvej 33 · DK-7800 Skive · Tel.: [phone] · Fax: [phone] · [e-mail] · www.deif.com
OPERATOR'S MANUAL
Genset Controller, GC-1F
●Push-buttons
●LEDs
●Icon list
●Display readings
Document no.: 4189340748A
SW version:

1. Delimitation
1.1. Scope of Operator’s Manual...................................................................................................................3
1.1.1. GC-1F ...........................................................................................................................................3
2. General information
2.1. Warnings, legal information and safety..................................................................................................4
2.1.1. Warnings and notes ......................................................................................................................4
2.1.2. Legal information and disclaimer ..................................................................................................4
2.1.3. Safety issues ................................................................................................................................4
2.1.4. Electrostatic discharge awareness ...............................................................................................4
2.1.5. Factory settings ............................................................................................................................4
2.2. About the Operator’s Manual.................................................................................................................5
2.2.1. General purpose ...........................................................................................................................5
2.2.2. Intended users ..............................................................................................................................5
2.2.3. Contents and overall structure ......................................................................................................5
2.3. Application information...........................................................................................................................5
2.3.1. UL applications .............................................................................................................................5
3. Push-buttons, LEDs and display
3.1. Unit.........................................................................................................................................................6
3.1.1. Dimensions ...................................................................................................................................6
3.1.2. Push-button functions ...................................................................................................................6
3.1.3. LED functions ...............................................................................................................................7
3.1.4. Display functions ...........................................................................................................................8
GC-1F operators manual 4189340748 UK
DEIF A/S Page 2 of 9

1. Delimitation
1.1 Scope of Operator’s Manual
1.1.1 GC-1F
This document covers the following GC-1F versions:
GC-1F SW version 1.2x.x
GC-1F/2 SW version 2.0x.x or later
GC-1F operators manual 4189340748 UK Delimitation
DEIF A/S Page 3 of 9

2. General information
2.1 Warnings, legal information and safety
2.1.1 Warnings and notes
Throughout this document, a number of warnings and notes with helpful user information will be presented.
To ensure that these are noticed, they will be highlighted as follows in order to separate them from the gener-
al text.
Warnings
Warnings indicate a potentially dangerous situation, which could result in death, personal in-
jury or damaged equipment, if certain guidelines are not followed.
Notes
Notes provide general information, which will be helpful for the reader to bear in mind.
2.1.2 Legal information and disclaimer
DEIF takes no responsibility for installation or operation of the engine set. If there is any doubt about how to
install or operate the engine controlled by the unit, the company responsible for the installation or the opera-
tion of the set must be contacted.
The units are not to be opened by unauthorised personnel. If opened anyway, the warranty will
be lost.
Disclaimer
DEIF A/S reserves the right to change any of the contents of this document without prior notice.
2.1.3 Safety issues
Installing and operating the unit may imply work with dangerous currents and voltages. Therefore, the instal-
lation should only be carried out by authorised personnel who understand the risks involved in working with
live electrical equipment.
Be aware of the hazardous live currents and voltages. Do not touch any AC measurement in-
puts as this could lead to injury or death.
2.1.4 Electrostatic discharge awareness
Sufficient care must be taken to protect the terminal against static discharges during the installation. Once the
unit is installed and connected, these precautions are no longer necessary.
2.1.5 Factory settings
The unit is delivered from factory with certain factory settings. These are based on average values and are
not necessarily the correct settings for matching the individual engine. Precautions must be taken to check
the settings before running the engine.
GC-1F operators manual 4189340748 UK General information
DEIF A/S Page 4 of 9

2.2 About the Operator’s Manual
2.2.1 General purpose
This document is the Operator’s Manual for DEIF’s generator controller GC-1F. The document includes infor-
mation about push-buttons, LEDs, display readings and icon list.
The general purpose is to give the operator important information to be used in the daily operation of the unit.
Please make sure to read this manual before working with the GC-1F controller and the genset
to be controlled. Failure to do this could result in damage to the equipment or human injury.
2.2.2 Intended users
This Operator’s Manual is mainly intended for the daily user. On the basis of this document, the operator will
be able to carry out simple day-to-day procedures.
2.2.3 Contents and overall structure
This document is divided into chapters, and in order to make the structure simple and easy to use, each
chapter will begin from the top of a new page.
2.3 Application information
2.3.1 UL applications
These flat surface panel-mounted controllers are intended to be used in Listed Generator Assemblies where
the suitability of the combination has been determined by Underwriters Laboratories.
These devices have been evaluated for fire and shock only. The accuracy and/or reliability of the voltage reg-
ulating function has not been evaluated. Metering, monitoring protection and signalling functions have not
been evaluated.
GC-1F operators manual 4189340748 UK General information
DEIF A/S Page 5 of 9

3. Push-buttons, LEDs and display
3.1 Unit
3.1.1 Dimensions
Front dimensions H x W 160 x 220 mm (6.30" x 8.66")
Unit depth 54 mm (2.13")
3.1.2 Push-button functions
The push-buttons on the unit have the following functions:
1500V 1500V 1500V
PROT VOLT GEN U1
HYSTERESIS 20%
LIMT DEL. HIST ACT
3
9
13
12
7
1011
4
5
21
6
8
1: Normal display: Scrolls the display down once. Programming: Decreases setpoint value.
2: Normal display: Scrolls the display up once. Programming: Increases setpoint value.
3: Resets horn relay. Extra function: Press and hold button 2 seconds to see alarm list.
4: Enters value/acknowledges alarm.
5: Jumps from parameter settings to display. Removes pop-up messages.
6: Initiates the test sequence selected for the push-button.
7: Lamp test. One push will illuminate all LEDs for 3 seconds.
8: Manual running mode selector.
9: AUTO running mode selector.
10: Breaker opens.
11: Breaker closes.
12: Stops the engine instantaneously. If the unit is in AUTO mode, the mode will change to MAN and the
engine will stop.
13: Start engine (local (not auto)) running mode.
GC-1F operators manual 4189340748 UK Push-buttons, LEDs and display
DEIF A/S Page 6 of 9

3.1.3 LED functions
1500V 1500V 1500V
PROT VOLT GEN U1
HYSTERESIS 20%
LIMT DEL. HIST ACT
3
5
67
2
4
1
8
1: Power OK indicator.
2: Flashing: active, non-acknowledged alarm(s) present.
Steady: active, acknowledged alarm(s) present.
3: Additional alarm indication LEDs:
Flashing: active, non-acknowledged alarm(s) where output A or B is configured to LED 1, 2, 3 or 4.
Steady: active, acknowledged alarm(s) where output A or B is configured to LED 1, 2, 3 or 4.
4: ON in manual mode.
5: ON in AUTO mode.
6: Generator breaker ON.
7: U/f OK, generator.
8: Running feedback present.
GC-1F operators manual 4189340748 UK Push-buttons, LEDs and display
DEIF A/S Page 7 of 9

3.1.4 Display functions
The display indicates both readings and alarms. The examples below are with icons and English language.
GC–1F
HW x.xx
SW x.xx
Type, hardware and software version.
Fuel level 80 %
Oil press 2.0 bar
Water 90°C
RPM 0
Fuel level, oil pressure, water temp. and RPM.
1 0 d 0 h
2 0 d 0 h
Run hours 24 h
Service timer 1 and 2.
Run hours.
Alarm list
2 alarm(s)
Press to enter the list of active alarms.
High Battery
Ack
2 alarm(s)
Active alarm list. The alarm list pops up automatically when an
alarm appears. When the arrow is present, more alarms are ac-
tive. Press ▼to scroll through the list. Exit the list by pressing
ESC.
Parameter
Press to enter the parameter setting.
D+ delay
0.0 s 10.0 s 100.0 s
Min. value Max. value
Actual value
Parameter example: D+ delay setting. Use ▲or ▼to scroll
through the settings list. If change of settings is necessary,
press and enter the password. Then use ▲or ▼to change
values. Use ESC to leave settings.
GC-1F operators manual 4189340748 UK Push-buttons, LEDs and display
DEIF A/S Page 8 of 9

The available parameters depend on the set options. Some parameters can only be changed
using the PC utility software (USW) for GC-1F. The parameter list will automatically be aban-
doned if no button is pressed during a 30 sec. period.
For detailed information about changing parameters and setup, please see the Installation In-
structions and Reference Handbook.
3 line views can show a max. value of 9999.
GC-1F operators manual 4189340748 UK Push-buttons, LEDs and display
DEIF A/S Page 9 of 9