Denali LAH.00.11600 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
LAH.00.11600
Denali Universal Mounting
12-14mm Bar Clamp Phone Mount
Instruction Manual
(a) Clamp Part for 12-14mm Tube......(LAH.00.017)......................Qty 1
(b) 8mm Spacer Plate......(LAH.00.018).......................................Qty 1
(c) 8-32 x 1-1/8 in Socket Head Screw DIN 9112..........................Qty 2
(d) 8-32 x 3/4 in Socket Head Screw DIN 9112.............................Qty 2
Kit Contents
Tools Required: 5/32 Hex wrench
(a)
(b)
(c)
(d)

1. Installing The Horn Mount DENALIELECTRONICS.COM
1.1 - Clamp Installation
Note: This clamp can be installed on pipes that range from 12 to 14mm in Diameter.
Step One: Based on fitment and clearances, determine whether you will need to use the
optional 8mm spacer (b) and longer screws (c) to mount your clamp and RAM Charger .
Step Two: Place the Clamp Bracket (a) over your bar in the desired location, make sure
the flat face is aimed towards you and the sloped faces point towards the windshield.
Step Three: Align the mounting holes on the back side of the RAM Charger with your
bracket and secure it using the Socket Head Screws (c or d).
Note: The whole assembly may have to be rotated downwards to have proper access
to your brackets (a) mounting holes.