Denali B6 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics is it extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
Whats In The Box?
Kit Contents
(a) B6 LED Brake Light Pod........................................................Qty 1
(b) Wiring Pigtail......................................................................Qty 1
Tools Required
Voltmeter/Multimeter
DENALIELECTRONICS.COM
B6 LED Brake Light
DNL.B6.003
Instruction Manual
(a)
(b)

1. Wiring The B6 Brake Light DENALIELECTRONICS.COM
Posi-Tap
1.1 - Identifying Vehicle Brake Wires
Note: If you are using the B6 Brake Light in conjunction with the DENALI
CANsmart Controller, please refer to the instruction manual of the
CANsmart Controller for brake light wiring.
Step One: Route the cable from the B6 Brake Light (a) into the rear of
the motorcycle to the area the factory brake light is located.
Step Two: Identify the wires coming from the factory tail light. There
will typically be only three wires exiting the factory brake light housing.
You will need to identify the Running Light Wire, Brake Light Wire as
1.2 - Wiring The Pigtail
well as the Ground Wire. Use a voltmeter or multimeter to assist in
identifying the correct wires.
Step Three: Use Posi-Tap connectors to wire the Pigtail (b) to the wires
identified in Step Two.
-Tap the Red Wire to Vehicle Running Light Wire
-Tap the Orange Wire to Vehicle Brake Light Wire
-Tap the Black Wire to Vehicle Ground Wire
Step Four: Plug the Pigtail (b) into the connector on the B6 Brake Light.
B6 LED Light Pod
Wiring Pigtail
Tap Black Wire to Vehicle Ground Wire - 12v Negative (-)
Tap Red Wire to Vehicle Running Light Wire - 12v Positive (+)
Tap Orange Wire to Vehicle Brake Light Wire - 12v Positive (+)