Denali DNL.WHS.24200 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our experts
a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front fork, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws and
bolts. It is also important to ensure that all hardware is tightened to the proper torque
specifications as listed in your owner’s manual. For included accessory hardware
please refer to the default torque specifications provided below. Inspect all hardware
after the first 30 miles to ensure that proper torque specifications are maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs -2.5Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 123
What’s In The Box?
DENALIELECTRONICS.COM
DENALIELECTRONICS.COM
Instruction Manual
(a) Switched Power Wiring Harness (Ducati DesertX).....................Qty 1
Switched Power Wiring Harness
Ducati DesertX
DNL.WHS.24200
OUTFITTING
GUIDE
Kit Contents
(a)

This Switched Power Wiring Harness enables plug-&-play connection that
provides Switched Power to DENALI LED Lights, like the Front T3 Switchback.
The pass through design allows for the Factory Ducati Accessory Pigtail to
still be used for additional electronics, while powering accessory DRLs.
Step One: Remove the (4) Screws that fasten the windscreen to the bike. The Accessory Connector is stowed within the dash cavity. It is a White,
2-Pin, JWPF style connector with a sealed pigtail.
Step Two: Locate the Accessory Connector and disconnect the Factory
Pigtail from the connector. Set the Factory Pigtail aside, so it can
reinstalled.
2.2 - Disconnect the Factory Pigtail
1. Harness Overview
1.1 - Overview of Harness
2.1 - Remove the Windscreen
DENALIELECTRONICS.COM
DENALIELECTRONICS.COM
2. Installing The Harness
Accessory
Pass-Through
Switched Power
Wiring location

DENALIELECTRONICS.COM
DENALIELECTRONICS.COM
When installing lighting such as Front T3 Switchbacks, there is the
opportunity to illuminate one of the DRL Circuits. This step shows how to
provide power to either the High or Low circuit. See the T3 Instruction
Manual for detailed steps.
Step One: Connect the Left and Right DRL wires to the Switched Power
Harness, with the included POSILOCK. Connector to either the 50% OR
100% intensity.
3.1 - Connect to Lighting
2. Installing the Harness (continued)
Switched Power
Harness
Step Three: Plug the Switched Power Adapter Harness to the bike’s
Accessory Connector.
Step Four: Plug the Factory Pigtail into the Adapter Harness. This serves
to seal the harness assembly, and can be used in the future for additional
accessories.
2.3 - Connect the Harness
3. Connect to Lighting
Right T3 Harness - Front
Left T3 Harness - Front
Reference: T3 Switchback Wiring
Not included in DesertX Switched Power Harness Kit.
Left Indicator - To Turn Signal
Right Indicator - To Turn Signal
DRL / 100%
DRL / 50%
Connect to Either 50% OR 100%
Switched Power
Output
Vehicle Accessory
Connector
Ground - To Turn Ground
Ground - To Turn Ground
Factory Pigtail