E2S GNExCP6C-PB User manual

European Safety Systems Ltd. Impress House, Mansell Road, Acton, London W3 7QH www.e2s.com Tel: [phone]
Document D154-00-155-IS Issue 8 12-09-2022 Sheet 1 of 3
INSTRUCTION MANUAL
GNExCP6C-PB Button Manual Call Point
For use in Flammable Gas and Dust Atmospheres
GNExCP6C-PB
Manual Call Point – Push Button
With Resistor Modules
For use in Flammable Gas and
Combustible Dust Atmospheres.
1) Introduction
The GNExCP6C-PB is a push button manual call
point which is certified to the European and
International Gas and Dust standards. The unit
meets the requirements of the ATEX directive
2014/34/EU, IECEx and UKEX schemes.
The call point can be used in hazardous areas
where potentially flammable gas and dust
atmospheres may be present.
All units have up to two of the following:
 Monitoring resistors up to 1.5W per module
 Monitoring diode
 Monitoring Zener diode
Units may also incorporate an LED indicator in
addition to the two series and/ or EOL devices
allowed.
The units are Group II, EPL (equipment protection
level) Gb. The equipment is certified ‘Ex db eb mb
IIC T4 Gb’ and as such may be used in Zones 1
and 2 with flammable gases and vapours with gas
groups IIA, IIB & IIC and temperature classes T1,
T2, T3 and T4.
These units are also Group III, EPL Db. The
equipment is certified ‘Ex tb IIIC T75ºC Db’ and as
such may be used in Zones 21 and 22 for
combustible dusts groups IIIA, IIIB & IIIC.
2) Ratings & Markings
All units have a rating label, which carries the
following important information: -
Unit Type No.:
GNExCP6C-PB Manual Call Point
Input Voltages:
Important: See section 7.1 for current ratings
125VDC Max 0.5A Max. Resistive Load;
0.03A Max Inductive Load
75VDC Max 0.75A Max
48VDC Max 1.0A Max
24VDC Max 5.0A Max Resistive Load;
3.0A Max Inductive Load
12VDC Max 5.0A Max
6VDC Max 5.0A Max
Code:
GNExCP6C-PB
Ex db eb mb IIC T4 Gb
Ex tb IIIC T75ºC Db
IP66
–40ºC <= Ta <= +65ºC
Certificate No.:
SIRA 09ATEX3286X
IECEx SIR 09.0121X
CSAE 21UKEX3556X
Epsilon x: II 2GD
CE Marking
Notified 2813
Body No.
UKCA Marking
Notified Body No. 0518
Year/Serial No. i.e. 20/1CP6CPB000001
WARNING - DO NOT OPEN WHEN AN
EXPLOSIVE ATMOSPHERE MAY BE PRESENT,
ELECTROSTATIC HAZARD – CLEAN ONLY
WITH A DAMP CLOTH
3) Type Approval Standards
The call point has an EC Type examination
certificate issued by SIRA and have been approved
to the following standards: -
EN60079-0:2018 / IEC60079-0:2017
EN60079-1:2014 / IEC60079-1:2014
EN60079-7:2015 / IEC60079-7:2017
EN60079-18:2015 / IEC60079-18:2014
EN60079-31:2014 / IEC60079-31:2013
The equipment is certified for use in ambient
temperatures in the range:
GNExCP6C-PB -40oC to +65oC
and shall not be used outside this range.
4) Installation Requirements
Installation of this equipment shall only be carried
out by suitably trained personnel in accordance
with the applicable code of practice e.g.
IEC 60079-14/EN 60079-14
Repair of this equipment shall only be carried out
by the manufacturer or in accordance with the
applicable code of practice e.g. IEC 60079-19/EN
60079-19.
Refer to certificates SIRA 09ATEX3286X, IECEx
SIR 09.0121X and CSAE 21UKEX3556X for
special conditions of safe use.
The certification of this equipment relies on the
following materials used in its construction:
Enclosure: GRP - Glass Reinforced Polyester
Through enclosure mechanism: Plastic Nylon Zytel
Injection Moulded
Sealing of enclosure and mechanism: O-ring
Acrylonitrile-Butadiene Rubber
Potting Compound of resistors where used: Epoxy
Resin
If the equipment is likely to come into contact with
aggressive substances, then it is the responsibility
of the user to take suitable precautions that prevent
it from being adversely affected, thus ensuring that
the type of protection is not compromised.
“Aggressive substances” - e.g. acidic liquids, gases
or solvents that may affect polymeric materials.
“Suitable precautions” - e.g. regular checks as part
of routine inspections or establishing from the
material’s data sheet that it is resistant to specific
chemicals.
Under extreme conditions the unit may generate an
ignition-capable level of electrostatic charges. The
unit must not be installed in a location where it may
be subjected to external conditions (such as high-
pressure steam) which may cause a build-up of
electrostatic charges on non-conducting surfaces.
Cleaning of the unit must only be carried out with a
damp cloth.
5) Call Point Location and Mounting
The location of the call point should enable ease of
access for operation and testing. The unit should
be mounted using the 4 off fixing holes which will
accept up to M5 sized fixings.
View of base unit showing fixing centres (in mm).
To gain access to the mounting holes in the base
the front cover must be removed.
This is achieved by removing the 4 off M4 cap
head bolts holding on the cover.

European Safety Systems Ltd. Impress House, Mansell Road, Acton, London W3 7QH www.e2s.com Tel: [phone]
Document D154-00-155-IS Issue 8 12-09-2022 Sheet 2 of 3
Once the screws are removed the cover will hang
down out of the way to gain access to the Ex e
terminal block, the internal earth terminal and
mounting hole recesses.
6) Earthing
The unit has an internal earth terminal.
It is recommended that a cable crimp lug is used
on the earth wires.
The internal earth wire is placed under an earth
clamp which will stop the cable twisting. This is
secured by an M4 screw and spring washer.
Internal Earth Ex e terminal block
terminal
7) Cable connections
There are 3 off cable entries for M20x1.5 Ex e
approved cable glands or stopping plugs with a
minimum ingress protection of IP66
The unit can be wired in a number of different ways
depending on the device combination selected.
EOL (End of line) device:
resistor – ExxxR / diode – ED1 / zener – ExxxZ
Series (In line) device:
resistor – SxxxR / diode – SD1 / zener – SxxxZ /
LED
Microswitch 1 = M/S 1
Microswitch 2 = M/S 2
The unit can be wired with a maximum of 2 module
devices – refer to wiring schematic D154-06-051
When wiring to Increased Safety terminal
enclosures, you are only permitted to connect one
wire into each way on the terminal block unless a
pair of wires are crimped into a suitable ferrule. For
the six-way terminal block wire sizes allowable are
0.5mm² to 4.0mm². For the 8-way DIN rail wire
sizes allowable are 0.5mm² to 2.5mm²
Leads connected to the terminals shall be insulated
for the appropriate voltage and this insulation shall
extend to within 1mm of the metal of the terminal
throat. They shall only be installed and wired with
cable in an ambient temperature of -10°C to +80°C
All terminal screws, used or unused, shall be
tightened down to between 0.5 Nm and 0.7 Nm.
Voltage
option
Max
Voltage
Min resistor value
allowable in
module
Type
C
unit (
1.5
W)
6 V dc
6 V dc
27 ohms
12V dc
12 V dc
110 ohms
24V dc
24 V dc
430 ohms
48V dc
48 V dc
1K8 ohms
Table 1
7.1) Current Limitations
The maximum allowable current is determined as
the smallest value from the following scenarios:
1. When both module resistor values are the
same as or above the minimum range of
values shown in table 1, the current is not
further limited.
However, when either resistor value is lower
than those shown in table 1, the current must
be limited to the values given in table 2.
Voltage
option
Max
Voltage
Max current when
resistor values
lower than
m
inimum
6 V dc
6 V dc
250mA
12V dc 12 V dc 125mA
24V dc
24 V dc
62mA
48V dc
48 V dc
31mA
Table 2
For example, if a 24V DC unit is fitted with a
series resistor of 270 ohms, the maximum
current of the unit would be reduced to 62mA
since the resistance is less than the minimum
430 ohms allowable at this voltage.
E2S recommends a minimum resistor value
of 100 ohms for a Series device and 180
ohms for an EOL device fitted to a 24V unit.
2. If a diode module is pre-fitted as either an
EOL or Series Device, the following current
limitation applies:
Unit Voltage
M
ax. Diode Current
48V DC
0.75A
6, 12
& 24V DC
2.0A
3. If a Zener diode module is pre-fitted as either
EOL or Series device, the following current
limitation applies:
Zener
Voltage
Max. Input
Voltage
Max. Current
3.3V
56V DC
230mA
4.7V 162mA
5.1V
149mA
5.6V
136mA
6.2V
12
2mA
6.8V 112mA
10V
76mA
12V
63mA
4. Units with LED code ‘C’
GNExCP6C-PBXXXXXXXXXC-XX-ExxxR-SxxxR
Maximum current is reduced to 20mA. In
this case, the current-limiting resistor for the
LED is not present, so that to safely power
the LED the maximum current must be
limited.
For units with LED code ‘L’, the current is
limited by the LED current-limiting resistor.
See value of this resistor in table below.
GNExCP6C-PBXXXXXXXXXL-XX-ExxxR-SxxxR
LED
Re
sistor
Max
.
Input Voltage
3
K3
(3300
ohms
)
56
V DC
1K5
(1500
ohms
)
28
V DC
8) Testing unit operation
The push button unit can be tested without the
need to replace any element.
To test, lift the cover lift flap to reveal the push
button. The button should be pressed into the body
to activate the unit and place it into the operated
condition.
The call point switch will now change over its
contacts to operate the alarm.
Once testing is complete the unit needs to be reset
from the operated condition.

European Safety Systems Ltd. Impress House, Mansell Road, Acton, London W3 7QH www.e2s.com Tel: [phone]
Document D154-00-155-IS Issue 8 12-09-2022 Sheet 3 of 3
Rotate the push button anticlockwise by an angle
of 55°, see guide alignment marks on the button
and cover, shown below (1). The push button
should pop back up to its original position.
Ensure that the push button has also twisted back
clockwise by 55° to its original position see guide
marks on button and cover, shown below (2). The
unit is now reset
1. On operated unit 2. Button should pop
twist push button up and twist back to
anticlockwise 55° original position
to reset
Resetting an operated unit is the same as resetting
a tested unit.
9) SIL 2 Reliability Data
Reliability and Functional safety IEC/EN61508
which has been assessed and is considered
suitable for use in low demand safety function:
• Random Hardware Failures and Systematic
Failures (route 2H)
• As an unvoted item (i.e. hardware fault tolerance
of 0) at SIL 2
The product was assessed against failure modes:
• Failure to close a contact when the call point is
struck with specified force
• Failure to open a contact when the call point is
struck with specified force
• Spurious output despite no input
Integrity in respect of failure to close SIL 2
Total Failure rate 0.133 pmh
“hazardous” failure rate (revealed) 0 pmh
“hazardous” failure rate (unrevealed) 0.1 pmh
“safe” failure rate (revealed) 0.033 pmh
“safe” failure rate (unrevealed) 0
Diagnostic Coverage 99%
System type A
Hardware Fault Tolerance 0
Safe Failure Fraction >99%
PFD (hazardous failure) 1.25 x 10-3
Proof Test Interval Up to 1 year
Note: use alignment
marks circled to
indicate the push
buttons
status/position
Unit currently shown
as ‘standby
condition’

Y
M/S 1
SERIES
-
+
M/S 1
-
+
87654321
R B Y
M/S 1
SERIES
EOL
-
+
M/S 1
-
+
87654321
R B Y
SERIES
M/S 1
EOL
-
+
M/S 1
-
+
87654321
R B
3 4
+
-
3 4
+
-
DIODE
ZENER
DIODE
DEVICE POLARITY
+
21
+
21
DEVICE POLARITY
ZENER
DIODEDIODE
--
2 3 4
+
-
+
DIODE
ZENER
DIODE
DEVICE POLARITY
2 3 4
+
-
+
2 3 4
+
-
2 3 4
+
-
DEVICE POLARITY
ZENER
DIODE
DIODE
-
2
+
3
+
4
-
5
EOL
2
SERIES
5
-
4
-
3
++
EOL
2
+
3
+
4
-
5
-
SERIES
1
SERIES
EOL
5
-
4
-
2
++
Series
Module [s]
EOL Module [e]
Product
Option [o]
GNEXCP6B-BG[s][t][l][e][m][d][v][o][x][u]-[v][e][s]
Product
Version [v]
LED Indicator [u]
Switch Type [s]
Terminals [t]
Y
M/S 1
EOL
-
+
M/S 1
-
+
87654321
R B
GNExCP6B/C/D/E CALL POINTS
D.HOWGILL
2S
CODING UPDATE FOR CONFIG 3 AND 4
D.A.H - 21-02-2022
TYPE E ADDED. DUAL VERSION
SCHEMATICS UPDATED. SHEET 3 ADDED
3
WWW.E2S.COM
C
LONDON W3 7QH
ACTON
MANSELL ROAD
IMPRESS HOUSE
EUROPEAN SAFETY SYSTEMS LTD
ACN0077
2FOR LED DIAGRAMS. D.A.H - 28-08-2020
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
EUROPEAN SAFETY SYSTEMS LTD.
WRITTEN CONSENT.
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
ANGULAR DIMENSIONAL TOLS
STANDARDS
MOD No. REASON - INITIAL - DATEISSUE
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
LINEAR DIMENSIONAL TOLS
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78 6
5
D
C
134
2
A
B
D154-06-051
R.N.POTTS
D.A.H - 17-11-2022
R.N.POTTS
07-02-20
OF
IF IN DOUBT, ASK -
CALL POINT WIRING SCHEMATIC
NTS 1 6
07-02-20
07-02-20
GNExCP6B/C/D/E-BG/PB/PT MANUAL
GEOMETRIC TOLERANCES TO ISO1101:1983
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
DRAWING TO BS8888:2000
DEVICE POLARITY ADDED. CONFIG 8 AND 12 ADDED (LED ONLY)
CONFIG 13 REMOVED, CONFIGS RE-NUMBERED 1 TO 24
4
warning signals
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) open
Terminals +(2,3) & (6) closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) closed
Terminals +(2,3) & (6) open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) open
Terminals +(2,3) & (6) closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) closed
Terminals +(2,3) & (6) open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) open
Terminals +(2,3) & (6) closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) closed
Terminals +(2,3) & (6) open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(1,2) & -(4,5) M/S 1 open
Terminals +(1,2) & (6) M/S 1 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(1,2) & -(4,5) M/S 1 closed
Terminals +(1,2) & (6) M/S 1 open
Module Device Codes
EOL Series
Resistor ExxxR SxxxR
Diode ED1 SD1
Zener Diode ExxxZ SxxxZ
LED N/A L or C
SINGLE MICROSWITCH | DEVICES
SINGLE SWITCH WITH EOL DEVICE SINGLE SWITCH WITH SERIES DEVICE
SWITCH TYPE [s]
PRODUCT OPTION [o]
EOL MODULE [e]
SINGLE SWITCH WITH EOL DEVICE CONFIG. 1 CONFIG. 2 SINGLE SWITCH WITH EOL & SERIES DEVICE
SWITCH TYPE [s]
PRODUCT OPTION [o]
MODULES [e][s]
SINGLE SWITCH WITH EOL & SERIES DEVICE
SWITCH TYPE [s]
PRODUCT OPTION [o]
MODULE [e][s]
CONFIG. 3 CONFIG. 4
Diagram Sheet
Dual Switch Wiring Configurations 2,4,5,6
LED Indicator Wiring Configurations 3,4,6
Parallel Dual Switch Wiring Configurations 5, 6
[S]
[1]
[Exxxx]
SWITCH TYPE [s]
PRODUCT OPTION [o]
SERIES MODULE [s]
Single
Standard
EOL Device
[S]
[1]
[Sxxxx]
Single
Standard
Series Device
[S]
[1]
[Exxxx][Sxxxx]
Single
Standard
EOL + Series
[S]
[W]
[Exxxx][Sxxxx]
Single
Alternative Wiring
EOL + Series
SHEET 1
PRODUCTS:
GNExCP6B/C/D/E - BG
GNExCP6B/C/D/E - PB
GNExCP6B/C/D/E - PT

Y
SERIES 2
SERIES 1
M/S 2
RYB
M/S 1
M/S 2
+
-
+
M/S 1
-
87654321
RB
B Y
M/S 2
R B
M/S 1
M/S 1
EOL 1
+
M/S 2
-
+
-
87654321
R Y
EOL 1
Y R Y B
EOL 1
M/S 2M/S 1
SERIES 1
M/S 2
+
-
+
M/S 1
-
87654321
RB
2
SERIES
7
-
6
+
3
-
EOL
+
2
SERIES SERIES
7
-
6
+
3
-+
1 5
-
EOL
4
+
2
-
EOL
+
+
1/5 2/6
-
1/5 2/6
-
+
DEVICE POLARITY
ZENER
DIODEDIODE
2/6
1/5
2/6
1/5
DIODE
ZENER
DIODE
DEVICE POLARITY
+ +
DIODE
ZENER
DIODE
DEVICE POLARITY
+
-
32
-
-
32
-
+
-
2
+
EOL
3
-
6
+
7
SERIES
Y
B
YR
1 2 3 4 5 6 7 8
-
M/S 1
+
-
+
M/S 2
SERIES 1
M/S 1 M/S 2
EOL 1
B
R
++
+
-
2 3
-
-
2 3
-
+
DEVICE POLARITY
ZENER
DIODEDIODE
Series
Module [s]
EOL Module [e]
Product
Option [o]
GNEXCP6B-BG[s][t][l][e][m][d][v][o][x][u]-[v][e][s]
Product
Version [v]
LED Indicator [u]
Switch Type [s]
Terminals [t]
GNExCP6B/C/D/E CALL POINTS
2S
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
WWW.E2S.COM
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
MOD No. REASON - INITIAL - DATEISSUE
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78 6
5
D
C
134
2
A
B
D154-06-051
D.HOWGILL
R.N.POTTS
R.N.POTTS
07-02-20
OF
GNExCP6B/C/D/E-BG/PB/PT MANUAL
CALL POINT WIRING SCHEMATIC
NTS 2 6
07-02-20
07-02-20
SEE SHEET 1
D.A.H - 28-08-2020
2ACN0077
3SEE SHEET 1
D.A.H - 06-07-2021
4SEE SHEET 1
D.A.H - 17-11-2022
warning signals
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals+ (1) & -(2) M/S 1 and +(4) & -(5) M/S 2 open
Terminals +(1) & (3) M/S 1 and +(4) & (6) M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals+ (1) & -(2) M/S 1 open and +(4) & -(5) M/S 2 closed
Terminals +(1) & (3) M/S 1 and +(4) & (6) M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) open
Terminals +(2,3) & (6) closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 closed
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 open
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 closed
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 open
Notes:
1. Other configurations of dual switch units are possible. Contact E2S sales to discuss options.
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 open
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 closed
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 open
DUAL MICROSWITCH | DEVICES
CONFIG. 8CONFIG. 7
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
MODULES [e][s]
DUAL SWITCH WITH EOL & SERIES DEVICE
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
MODULES [e][s]
DUAL SWITCH WITH EOL & SERIES DEVICECONFIG. 6
SWITCH TYPE [s]
PRODUCT OPTION [o]
EOL MODULE [e]
DUAL SWITCH WITH SERIES DEVICES
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
SERIES MODULE [s]
CONFIG. 5DUAL SWITCH WITH EOL DEVICE
Module Device Codes
EOL Series
Resistor ExxxR SxxxR
Diode ED1 SD1
Zener Diode ExxxZ SxxxZ
LED N/A L or C
Dual
Standard
EOL Device
[D]
[1]
[Exxxx]
Dual
DIN Rail Only
Standard
Series Device
[D]
[D]
[1]
[Sxxxx]
Dual
DIN Rail Only
Standard
EOL + Series
[D]
[D]
[1]
[Exxxx][Sxxxx]
Dual
DIN Rail Only
Alternative Wiring
EOL + Series
[D]
[D]
[W]
[Exxxx][Sxxxx]
SHEET 2

LED
SERIES
M/S 1
RL1
-
+
M/S 1
-
+
87654321
R
Y B LED
M/S 1
RL1
EOL
-
+
M/S 1
-
+
87654321
R
Y B
SERIES
2
+
3
+
4
-
5
-
LED
2
LED
EOL
5
-
4
-
3
++
1 2
+
1 2
+
DIODE
ZENER
DIODE
DEVICE POLARITY
3 4
+
-
3 4
+
-
DIODE
ZENER
DIODE
DEVICE POLARITY
2
LED
5
-
4
-
3
++
BY
R
1 2 3 4 5 6 7 8
+
-
M/S 1
+
-
RL1
M/S 1
LED
Series
Module [s]
EOL Module [e]
Product
Option [o]
GNEXCP6B-BG[s][t][l][e][m][d][v][o][x][u]-[v][e][s]
Product
Version [v]
LED Indicator [u]
Switch Type [s]
Terminals [t]
LED
SERIES
M/S 1
RL1
EOL
-
+
M/S 1
-
+
87654321
R
Y B
LED
SERIES
EOL
5
-
4
-
3
+
2
+
DIODE
ZENER
DIODE
DEVICE POLARITY
-
2 3 4
+
-
+
RL1
-
2 3 4
+
-
+
RL1
GNExCP6B/C/D/E CALL POINTS
2S
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
WWW.E2S.COM
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
MOD No. REASON - INITIAL - DATEISSUE
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78 6
5
D
C
134
2
A
B
D154-06-051
D.HOWGILL
R.N.POTTS
R.N.POTTS
07-02-20
OF
GNExCP6B/C/D/E-BG/PB/PT MANUAL
CALL POINT WIRING SCHEMATIC
NTS 3 6
07-02-20
07-02-20
SEE SHEET 1
D.A.H - 17-11-2022
4
SEE SHEET 1
D.A.H - 06-07-2021
3
ACN00772SEE SHEET 1
D.A.H - 28-08-2020
warning signals
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) open
Terminals +(2,3) & (6) closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) closed
Terminals +(2,3) & (6) open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) open
Terminals +(2,3) & (6) closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) closed
Terminals +(2,3) & (6) open
Notes:
1. LED available only on GNExCP6B and GNExCP6C Units
2. GNExCP6C Units have the option to remove the LED current-limiting resistor RL1
using LED option 'C'. In all other cases, RL1 is included.
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) open
Terminals +(2,3) & (6) closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) closed
Terminals +(2,3) & (6) open
SINGLE MICROSWITCH | LED |DEVICES
CONFIG. 11
SWITCH TYPE [s]
PRODUCT OPTION [o]
LED INDICATOR [u]
EOL MODULE [e]
SINGLE SWITCH WITH LED & EOL DEVICECONFIG. 10
SWITCH TYPE [s]
PRODUCT OPTION [o]
LED INDICATOR [u]
SINGLE SWITCH WITH LED & SERIES DEVICE
SWITCH TYPE [s]
PRODUCT OPTION [o]
LED INDICATOR [u]
SERIES MODULE [s]
CONFIG. 9SINGLE SWITCH WITH LED ONLY
Module Device Codes
EOL Series
Resistor ExxxR SxxxR
Diode ED1 SD1
Zener Diode ExxxZ SxxxZ
LED N/A L or C
[S]
[1]
[L]
Single
Standard
LED
Single
Standard
LED
Series Device
[S]
[1]
[L]
[Sxxxx]
Single
Standard
LED
EOL Device
[S]
[1]
[L]
[Exxxx]
SHEET 3
[S]
[1]
[L]
[Exxxx][Sxxxx]
Single
Standard
LED
EOL + Series Device
SWITCH TYPE [s]
PRODUCT OPTION [o]
LED INDICATOR [u]
MODULES [e][s]
CONFIG. 12 SINGLE SWITCH WITH LED, EOL & SERIES DEVICE
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) open
Terminals +(2,3) & (6) closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) closed
Terminals +(2,3) & (6) open

LED
7
-
6
+
3
-
2
+
SERIES
EOL
R
LED
RL1
B
Y
1 2 3 4 5 6 7 8
-
M/S 1
+
-
+
M/S 2
SERIES 1
M/S 1 M/S 2
EOL 1
B
Y
R
EOL 2
R Y B
EOL 1
M/S 2M/S 1
M/S 2
+
-
+
M/S 1
-
87654321
YB
RL1
LED
R
SERIES 1
RYB
M/S 2M/S 1
SERIES 1
M/S 2
+
-
+
M/S 1
-
87654321
YB
RL1
LED
R
2/6 3/7
-
+
2/6 3/7
-
+
DEVICE POLARITY
ZENER
DIODEDIODE
1/5 2/6
+
1/5 2/6
+
1/5 2/6
+
DIODE
ZENER
DIODE
DEVICE POLARITY
+
-
321
RL1
+
-
321
RL1
DEVICE POLARITY
ZENER
DIODE
DIODE
+
EOL
7
-
6
+
3
-
EOL
2
LED
7
SERIES
LED
SERIES
2
+
3
-
6
+ -
+
7
-
6
+
3
-
2
LED
R
LED
RL1
B
Y
1 2 3 4 5 6 7 8
-
M/S 1
+
-
+
M/S 2
M/S 1 M/S 2
B
YR
Series
Module [s]
EOL Module [e]
Product
Option [o]
GNEXCP6B-BG[s][t][l][e][m][d][v][o][x][u]-[v][e][s]
Product
Version [v]
LED Indicator [u]
Switch Type [s]
Terminals [t]
GNExCP6B/C/D/E CALL POINTS
2S
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
WWW.E2S.COM
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
MOD No. REASON - INITIAL - DATEISSUE
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78 6
5
D
C
134
2
A
B
D154-06-051
D.HOWGILL
R.N.POTTS
R.N.POTTS
07-02-20
OF
GNExCP6B/C/D/E-BG/PB/PT MANUAL
CALL POINT WIRING SCHEMATIC
NTS 4 6
07-02-20
07-02-20
SEE SHEET 1
D.A.H - 17-11-2022
4
SEE SHEET 1
D.A.H - 06-07-2021
3
ACN00772SEE SHEET 1
D.A.H - 28-08-2020
warning signals
Notes:
1. LED available only on GNExCP6B and GNExCP6C Units
2. GNExCP6C Units have the option to remove the LED current-limiting resistor RL1
using LED option 'C'. In all other cases, RL1 is included.
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 open
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 closed
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 open
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 closed
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 open
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 closed
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 open
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2) & -(3) M/S 1 and +(6) & -(7) M/S 2 closed
Terminals +(2) & (4) M/S 1 and +(6) & (8) M/S 2 open
DUAL MICROSWITCH | LED | DEVICES
Module Device Codes
EOL Series
Resistor ExxxR SxxxR
Diode ED1 SD1
Zener Diode ExxxZ SxxxZ
LED N/A L or C
DUAL SWITCH WITH LED CONFIG. 13
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
LED INDICATOR [u]
DUAL SWITCH WITH LED & EOL DEVICE
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
LED INDICATOR [u]
EOL MODULE [e]
CONFIG. 14 DUAL SWITCH WITH LED & SERIES DEVICE CONFIG. 15
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
LED INDICATOR [u]
SERIES MODULE [s]
DUAL SWITCH WITH LED, EOL & SERIES DEVICE CONFIG. 16
[D]
[D]
[1]
[L]
Dual
DIN Rail Only
Standard
LED
[D]
[D]
[1]
[L]
[ExxxR]
Dual
DIN Rail Only
Standard
LED
EOL Device
[D]
[D]
[1]
[L]
[Sxxxx]
Dual
DIN Rail Only
Standard
LED
Series Device
Dual
DIN Rail Only
Standard
LED
EOL + Series
[D]
[D]
[1]
[L]
[Exxxx][Sxxxx]
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
LED INDICATOR [u]
MODULES [e][s]
SHEET 4

Series
Module [s]
EOL Module [e]
Product
Option [o]
GNEXCP6B-BG[s][t][l][e][m][d][v][o][x][u]-[v][e][s]
Product
Version [v]
LED Indicator [u]
Switch Type [s]
Terminals [t]
GNExCP6B/C/D/E CALL POINTS
2S
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
WWW.E2S.COM
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
MOD No. REASON - INITIAL - DATEISSUE
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78 6
5
D
C
134
2
A
B
D154-06-051
D.HOWGILL
R.N.POTTS
R.N.POTTS
07-02-20
OF
GNExCP6B/C/D/E-BG/PB/PT MANUAL
CALL POINT WIRING SCHEMATIC
NTS 5 6
07-02-20
07-02-20
SEE SHEET 1
D.A.H - 17-11-2022
4
SEE SHEET 1
D.A.H - 06-07-2021
3
ACN00772SEE SHEET 1
D.A.H - 28-08-2020
warning signals
Module Device Codes
EOL Series
Resistor ExxxR SxxxR
Diode ED1 SD1
Zener Diode ExxxZ SxxxZ
LED N/A L or C
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals+ (2,3) & -(4,5) M/S 1 & M/S 2 open
Terminals +(2,3) & (6) M/S 1 & M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals+ (2,3) & -(4,5) M/S 1 & M/S 2 closed
Terminals +(2,3) & (6) M/S 1 & M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) M/S 1 & M/S 2 open
Terminals +(2,3) & (6) M/S 1 & M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) M/S 1 & M/S 2 closed
Terminals +(2,3) & (6) M/S 1 & M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(2,3) & -(4,5) M/S 1 & M/S 2 open
Terminals +(2,3) & (6) M/S 1 & M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(2,3) & -(4,5) M/S 1 & M/S 2 closed
Terminals +(2,3) & (6) M/S 1 & M/S 2 open
Notes:
1. Other configurations of dual switch units are possible. Contact E2S sales to discuss options.
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(3,4) & -(5,6) M/S 1 & M/S 2 open
Terminals +(3,4) & (7) M/S 1 & M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(3,4) & -(5,6) M/S 1 & M/S 2 closed
Terminals +(3,4) & (7) M/S 1 & M/S 2 open
DUAL MICROSWITCHES IN PARALLEL
CONFIG. 20CONFIG. 19 DUAL SWITCH WITH EOL & SERIES DEVICEDUAL SWITCH WITH EOL & SERIES DEVICECONFIG. 18DUAL SWITCH WITH SERIES DEVICESCONFIG. 17DUAL SWITCH WITH EOL DEVICE
4
-
EOL
2
+
R
M/S 2
B
M/S 1
M/S 1 & M/S 2
EOL 1
-
87654321
R Y B
SERIES 1
M/S 2
RY B
M/S 1
87654321
RYB
-
+ +
--
+ +
SERIES
3
-
2
+
RY B
M/S 2M/S 1
SERIES 1
87654321
RY B
SERIES
3
-
EOL
2
+
--
+ +
EOL 1
YR
1 2 3 4 5 6 7 8
SERIES 1
M/S 1 M/S 2
EOL 1
BYR
3
+
EOL
5
-
SERIES
--
+ +
B
+
2/3 4/5
-
2/3 4/5
-
+
DEVICE POLARITY
ZENER
DIODE
DIODE
2/3
1
2/3
1
DIODE
ZENER
DIODE
DEVICE POLARITY
+ +
DIODE
ZENER
DIODE
DEVICE POLARITY
+
-
4/52/3
-
-
4/52/3
-
+
++
+
-
-
-
3/4 5/6
-
+
DEVICE POLARITY
ZENER
DIODE
DIODE
3
+
5
-
3
+
5
-3
+
5
-
4
+
6
-
--
3/4 5/6
M/S 1 & M/S 2 M/S 1 & M/S 2 M/S 1 & M/S 2
SWITCH TYPE [s]
PRODUCT OPTION [o]
EOL MODULE [e]
[D]
[P]
[Exxxx]
Dual
Parallel Wiring
EOL Device
SWITCH TYPE [s]
PRODUCT OPTION [o]
SERIES MODULE [s]
[D]
[P]
[Sxxxx]
Dual
Parallel Wiring
Series Device
SWITCH TYPE [s]
PRODUCT OPTION [o]
MODULE [e][s]
[D]
[P]
[Exxxx][Sxxxx]
Dual
Parallel Wiring
EOL + Series
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
MODULE [e][s]
[D]
[D]
[V]
[Exxxx][Sxxxx]
Dual
DIN Rail Only
Alternative Parallel
Switch Wiring
EOL + Series
SHEET 5
Y

Series
Module [s]
EOL Module [e]
Product
Option [o]
GNEXCP6B-BG[s][t][l][e][m][d][v][o][x][u]-[v][e][s]
Product
Version [v]
LED Indicator [u]
Switch Type [s]
Terminals [t]
GNExCP6B/C/D/E CALL POINTS
2S
EUROPEAN SAFETY SYSTEMS LTD
IMPRESS HOUSE
MANSELL ROAD
ACTON
LONDON W3 7QH
WWW.E2S.COM
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
MOD No. REASON - INITIAL - DATEISSUE
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78 6
5
D
C
134
2
A
B
D154-06-051
D.HOWGILL
R.N.POTTS
R.N.POTTS
07-02-20
OF
GNExCP6B/C/D/E-BG/PB/PT MANUAL
CALL POINT WIRING SCHEMATIC
NTS 6 6
07-02-20
07-02-20
SEE SHEET 1
D.A.H - 17-11-2022
4
SEE SHEET 1
D.A.H - 06-07-2021
3
ACN00772SEE SHEET 1
D.A.H - 28-08-2020
warning signals
Module Device Codes
EOL Series
Resistor ExxxR SxxxR
Diode ED1 SD1
Zener Diode ExxxZ SxxxZ
LED N/A L or C
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals+ (2,3) & -(4,5) M/S 1 & M/S 2 open
Terminals +(2,3) & (6) M/S 1 & M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals+ (2,3) & -(4,5) M/S 1 & M/S 2 closed
Terminals +(2,3) & (6) M/S 1 & M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(3,4) & -(5,6) M/S 1 & M/S 2 open
Terminals +(3,4) & (7) M/S 1 & M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(3,4) & -(5,6) M/S 1 & M/S 2 closed
Terminals +(3,4) & (7) M/S 1 & M/S 2 open
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals +(3,4) & -(5,6) M/S 1 & M/S 2 open
Terminals +(3,4) & (7) M/S 1 & M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals +(3,4) & -(5,6) M/S 1 & M/S 2 closed
Terminals +(3,4) & (7) M/S 1 & M/S 2 open
DUAL MICROSWITCHES IN PARALLEL | LED
CONFIG. 24CONFIG. 23 DUAL SWITCH WITH EOL & SERIES DEVICEDUAL SWITCH WITH SERIES DEVICECONFIG. 22DUAL SWITCH WITH EOL DEVICECONFIG. 21DUAL SWITCH WITH LED
4
-
EOL
2
+
Y
M/S 2
R B
M/S 1
M/S 1 & M/S 2
EOL 1
-
87654321
R Y B
SERIES 1
YY B
87654321
RB
-
+ +
--
+ +
SERIES
3
-
2
+
87654321
SERIES
3
-
EOL
2
+
--
+ +
+
2/3 4/5
-
2/3 4/5
-
+
DEVICE POLARITY
ZENER
DIODE
DIODE
3/4
2
3/4
2
DIODE
ZENER
DIODE
DEVICE POLARITY
+ +
DIODE
ZENER
DIODE
DEVICE POLARITY
+
-
5/63/4
-
-
5/63/4
-
+
3
+
5
-
3
+
5
-3
+
5
-
--
M/S 1 & M/S 2 M/S 1 & M/S 2
SWITCH TYPE [s]
PRODUCT OPTION [o]
LED INDICATOR [u]
[D]
[P]
[L]
Dual
Parallel Wiring
LED
SWITCH TYPE [s]
PRODUCT OPTION [o]
LED INDICATOR [u]
EOL MODULE [e]
[D]
[P]
[L]
[Exxxx]
Dual
Parallel Wiring
LED
EOL Device
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
LED INDICATOR [u]
SERIES MODULE [s]
[D]
[D]
[P]
[L]
[Sxxxx]
Dual
DIN Rail Only
Parallel Wiring
LED
Series Device
SWITCH TYPE [s]
TERMINALS [t]
PRODUCT OPTION [o]
LED INDICATOR [u]
MODULE [e][s]
[D]
[D]
[P]
[L]
[Exxxx][Sxxxx]
Dual
DIN Rail Only
Parallel Wiring
LED
EOL + Series
LED
RL1
Circuit shown in Unoperated condition
Unoperated condition
(Glass Intact / Standby Condition)
Terminals+ (2,3) & -(4,5) M/S 1 & M/S 2 open
Terminals +(2,3) & (6) M/S 1 & M/S 2 closed
Operated condition
(Glass Broken / Button pushed in)
Terminals+ (2,3) & -(4,5) M/S 1 & M/S 2 closed
Terminals +(2,3) & (6) M/S 1 & M/S 2 open
4
-
2
+
Y
M/S 2
B
M/S 1
M/S 1 & M/S 2
-
87654321
R Y B
-
+ +
3
+
5
-
LED
RL1
LED
LED
LED
M/S 2M/S 1
RL1
R
SERIES 1
Y Y B
RB
M/S 2M/S 1
RL1
R
EOL 1
LED
SHEET 6
R
Notes:
1. LED available only on GNExCP6B and GNExCP6C Units
2. GNExCP6C Units have the option to remove the LED current-limiting resistor RL1
using LED option 'C'. In all other cases, RL1 is included.

E2S Telephone: [phone] Fax: [phone] Email: [email protected]om www.e2s.com DC-043_Issue_J (GNExPC6) - Page 1 of 2 - QAF_252_Issue_5
EU Declaration of Conformity
Manufacturer: European Safety Systems Ltd.
Impress House, Mansell Road, Acton
London, W3 7QH
United Kingdom
Authorised Representative: E2S Warnsignaltechnik UG
Charlottenstrasse 45-51
72764 Reutlingen
Germany
Equipment Type: GNExCP6A-BG, GNExCP6A-PB, GNExCP6A-PT
GNExCP6B-BG, GNExCP6B-PB, GNExCP6B-PT,
GNExCP6C-BG, GNExCP6C-PB, GNExCP6C-PT
GNExCP6D-BG, GNExCP6D-PB, GNExCP6D-PT
GNExCP6E-BG, GNExCP6E-PB, GNExCP6E-PT
Directive 2014/34/EU: Equipment and Protective Systems for use in Potentially Explosive Atmospheres (ATEX)
Notified Body for EU type Examination (Module B):
Sira Certification Service
Notified Body No.: 2813
CSA Group Netherlands B.V, Utrechtseweg 310, 6812 AR, Arnhem, Netherlands
EU-type Examination Certificate (Module B):
Sira 09ATEX3286X
Notified Body for Quality Assurance Notification / Conformity to EU-type
based on
quality assurance of the production process (Module D):
Sira Certification Service
Notified Body No.: 2813
CSA Group Netherlands B.V, Utrechtseweg 310, 6812 AR, Arnhem, Netherlands
Quality Assurance Notification (Module D):
SIRA 05 ATEX M342
Provisions fulfilled by the equipment: GNExCP6A:
GNExCP6B:
GNExCP6C:
GNExCP6D:
GNExCP6E:
II 2G Ex db eb IIC T6 Gb (-40°C ≤ Ta ≤ +70°C)
II 2D Ex tb IIIC T75°C Db (-40°C ≤ Ta ≤ +70°C)
or
II 2G Ex db eb mb IIC T4 Gb (-40°C ≤ Ta ≤ +50°C)
II 2D Ex tb IIIC T80°C Db (-40°C ≤ Ta ≤ +50°C)
or
II 2G Ex db eb mb IIC T4 Gb (-40°C ≤ Ta ≤ +65°C)
II 2D Ex tb IIIC T75°C Db (-40°C ≤ Ta ≤ +65°C)
or
II 2G Ex db eb mb IIC T4 Gb (-40°C ≤ Ta ≤ +70°C)
II 2D Ex tb IIIC T80°C Db (-40°C ≤ Ta ≤ +70°C)
or
II 2G Ex db eb mb IIC T4 Gb (-40°C ≤ Ta ≤ +65°C)
II 2D Ex tb IIIC T75°C Db (-40°C ≤ Ta ≤ +65°C)
Standards applied:
EN IEC 60079-0:2018
EN 60079-1:2014
EN 60079-7:2015/A1:2108
IEC 60079-18:2015/AC:2018
EN 60079-31: 2014
IP6X Dust Protection to EN60079-0 / EN 60079-31
Directive 2014/30/EU: Electromagnetic Compatibility Directive (EMC)
Standards applied:
EN 61000-6-1:2007
EN 61000-6-2:2005
EN 61000-6-3:2007 / A1:2011 / AC: 2012
EN 61000-6-4:2007 / A1: 2011

E2S Telephone: [phone] Fax: [phone] Email: [email protected]om www.e2s.com DC-043_Issue_J (GNExPC6) - Page 2 of 2 - QAF_252_Issue_5
Martin Streetz
Document No.:
DC-043_Issue_J
Quality Assurance Manager
Date and Place of Issue:
London, 23/12/2020
EU Declaration of Conformity
Directive 2011/65/EU: Restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS)
The product and all the components contained within it are in accordance with the restriction of the use of hazardous substances in electrical and electronic
equipment, including amendment by Directive 2015/863/EU.
Regulation (EC) 1907/2006: Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH)
The product and all the components contained within it are free from substances of very high concern.
Other Standards and Regulations
EN 60529:1992+A2:2013 - Degrees of protection provided by enclosures (IP code) –enclosure rated IP66
On behalf of European Safety Systems Ltd., I declare that, on the date the equipment accompanied by this declaration is placed on the market, the equipment
conforms with all technical and regulatory requirements of the above listed directives, regulations and standards.
This Declaration is issued under the sole responsibility of the manufacturer.

E2S Telephone: [phone] Fax: [phone] Email: [email protected] www.e2s.com DC-094_Issue_A (GNExCP6) - Page 1 of 2 - QAF_252_Issue_5
UKCA Declaration of Conformity
Manufacturer: European Safety Systems Ltd.
Impress House, Mansell Road, Acton
London, W3 7QH
United Kingdom
Equipment Type: GNExCP6A-BG, GNExCP6A-PB, GNExCP6A-PT
GNExCP6B-BG, GNExCP6B-PB, GNExCP6B-PT,
GNExCP6C-BG, GNExCP6C-PB, GNExCP6C-PT
GNExCP6D-BG, GNExCP6D-PB, GNExCP6D-PT
GNExCP6E-BG, GNExCP6E-PB, GNExCP6E-PT
Directive UKSI 2016:1107 (as amended by UKSI 2019:696) – Schedule 3A, Part 1 : Product or Protective System Intended for use in Potentially Explosive Atmospheres
(UKCA)
Notified Body for
UK
type Examination
(Module B)
:
Sira Certification Service
Notified Body No.: 0518
Rake Lane, Eccleston, Chester CH4 9JN, UK
UK
-
type Examination Certificate
(Module B)
:
CSAE 21
UKEX3556X
Notified Body for Quality Assurance Notification
/
Conformity to EU
-
type
based on
quality assurance of the production process (Module D):
Sira Certification Service
Notified Body No.: 0518
Rake Lane, Eccleston, Chester CH4 9JN, UK
Quality Assurance Notification
(Module D)
:
CSAE 22UKQAN0046
Provisions fulfilled by the equipment:
GN
ExCP
6
A
:
GNExCP6B:
GNExCP6C:
GNExCP6D:
GNExCP6E:
II 2G Ex
db
eb IIC T6 Gb (
-
40°C
≤ Ta ≤ +70°C)
II 2D Ex tb IIIC T75°C Db (-40°C ≤ Ta ≤ +70°C)
or
II 2G Ex db eb mb IIC T4 Gb (-40°C ≤ Ta ≤ +50°C)
II 2D Ex tb IIIC T80°C Db (-40°C ≤ Ta ≤ +50°C)
or
II 2G Ex db eb mb IIC T4 Gb (-40°C ≤ Ta ≤ +65°C)
II 2D Ex tb IIIC T75°C Db (-40°C ≤ Ta ≤ +65°C)
or
II 2G Ex db eb mb IIC T4 Gb (-40°C ≤ Ta ≤ +70°C)
II 2D Ex tb IIIC T80°C Db (-40°C ≤ Ta ≤ +70°C)
or
II 2G Ex db eb mb IIC T4 Gb (-40°C ≤ Ta ≤ +65°C)
II 2D Ex tb IIIC T75°C Db (-40°C ≤ Ta ≤ +65°C)
Standards applied:
EN IEC 60079
-
0:2018
EN 60079-1:2014
EN 60079-7:2015/A1:2108
IEC 60079-18:2015/AC:2018
EN 60079-31: 2014
IP6X Dust Protection to EN60079-0 / EN 60079-31
Directive 2014/30/EU: Electromagnetic Compatibility Directive (EMC)
Standards applied:
EN 61000
-
6
-
1:2007
EN 61000-6-2:2005
EN 61000-6-3:2007 / A1:2011 / AC: 2012
EN 61000-6-4:2007 / A1: 2011
Directive 2011/65/EU: Restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS)
The product and all the components contained within it are in accordance with the restriction of the use of hazardous substances in electrical and electronic
equipment, including amendment by Directive 2015/863/EU.
Regulation (EC) 1907/2006: Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH)
The product and all the components contained within it are free from substances of very high concern.

E2S Telephone: [phone] Fax: [phone] Email: [email protected] www.e2s.com DC-094_Issue_A (GNExCP6) - Page 2 of 2 - QAF_252_Issue_5
Martin Streetz Document No.: DC-094_Issue_A
Quality Assurance Manager Date and Place of Issue: London, 04/02/2022
UKCA Declaration of Conformity
Other Standards and Regulations
EN 60529:1992+A2:2013 - Degrees of protection provided by enclosures (IP code) – enclosure rated IP66
On behalf of European Safety Systems Ltd., I declare that, on the date the equipment accompanied by this declaration is placed on the market, the equipment
conforms with all technical and regulatory requirements of the above listed directives, regulations and standards.
This Declaration is issued under the sole responsibility of the manufacturer.